TWN4 MULTITECH 2 LEGIC M LF HF INTEGRATION MANUAL
TABLE OF CONTENTS 1 INTRODUCTION .................................................................................................................................................................. 3 1.1 ABOUT THIS MANUAL ..................................................................................................................................................3 1.2 ABOUT TWN4 MULTITECH 2 LEGIC M LF HF ...................................................................................................
1 INTRODUCTION 1.1 ABOUT THIS MANUAL This integration manual explains how to integrate ELATEC RFID reader/writer module TWN4 MultiTech 2 LEGIC M LF HF into a host device and is mainly intended for integrators and host manufacturers. Before installing the product, the integrators should read and understand the content of this integration manual and other relevant installation documents. The content of this integration manual is subject to changes without prior notice and printed versions might be obsolete.
2 SAFETY INFORMATION • ELATEC TWN4 MultiTech 2 LEGIC M LF HF is an electronic component and should be installed exclusively by a trained and • • • • qualified personnel. ELATEC recommends the integrators to follow general ESD protective measures during the installation of TWN4 MultiTech 2 LEGIC M LF HF into a host device, e.g. the use of an antistatic wristband or special gloves.
3 INTEGRATION INSTRUCTIONS 3.1 GENERAL TWN4 MultiTech 2 LEGIC M LF HF may be installed in any host devices, as long as it is operated under the operational conditions stated in the user manual and other technical documents (e.g. data sheet). TWN4 MultiTech 2 LEGIC M LF HF is equipped with two integrated antennas. Thus, no antenna installation is required. 3.
3.7 ANTENNAS The reader module is equipped with the following antennas: HF antenna (13.56 MHz) Dimensions: 42 x 47 mm / 1.65 x 1.85 inch Number of turns: 3 LF antenna (125 kHz) Diameter: 16 mm / 0.63 inch Number of turns: 120 For more information, refer to the related product data sheet or other relevant technical documents. TWN4 MultiTech 2 LEGIC M LF HF (exemplary picture) 3.
3.12 ELECTRICAL CONNECTION The module can be connected to the host with a DF11 connector*. PIN 1 2 3 4 5 6 7 8 PIN NAME UGND USB_D+ UVCC USB_DV24_RXD GND V24_TXD Hostsense FUNCTION USB Ground. Fed to main Ground through noise-reduction circuit. USB Data + USB VCC (5V). When using RS-232, connect this to external 5V supply. USB Data RS-232 RXD (Input) Ground RS-232 TXD (Output) Active-low, enables RS-232 transceiver. Short to Pin 6 (GND) when using RS-232.
4 COMPLIANCE STATEMENTS 4.1 EU TWN4 MultiTech 2 LEGIC M LF HF is in compliance with the EU directives and regulations as listed in the respective declaration of conformity. 4.2 FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
4.4 UNITED KINGDOM TWN4 MultiTech 2 LEGIC M LF HF complies with the requirements of the UK legislations and other regulations as listed in the respective UK declaration of conformity. The importer is responsible for applying the following information to the packaging of the product: • the importer company’s details, including the company’s name and a contact address in the United Kingdom. • UKCA marking 4.
5 INTEGRATOR AND HOST REQUIREMENTS Authorization requirements TWN4 MultiTech 2 LEGIC M LF HF has been certified as a module and does not need further approval, provided that the module is used in accordance with the FCC grant conditions and no limitations or usage conditions have been defined by ELATEC. However, the host manufacturer must ensure that the host device still complies with all applicable regulations after TWN4 MultiTech 2 LEGIC M LF HF has been integrated.
APPENDIX A – TERMS AND ABBREVIATIONS TERM host device Integrator KDB modular type n/a RFID (reader/writer) module EXPLANATION Also “host” or “host product”. Device in which an RFID module is intended to be installed for operation. Responsible party for the integration of an RFID module into a host device. The integrator might be the module manufacturer, the host manufacturer, the end user or any other third party.
ELATEC GMBH Zeppelinstr. 1 • 82178 Puchheim • Germany P +49 89 552 9961 0 • F +49 89 552 9961 129 • E-mail: info-rfid@elatec.com elatec.com Elatec reserves the right to change any information or data in this document without prior notice. Elatec declines all responsibility for the use of this product with any other specification but the one mentioned above. Any additional requirement for a specific customer application has to be validated by the customer himself at his own responsibility.