TWN4 MULTITECH NANO LEGIC 42 M INTEGRATION MANUAL
TABLE OF CONTENTS 1 INTRODUCTION.................................................................................................................................................................. 3 1.1 ABOUT THIS MANUAL ..................................................................................................................................................3 1.2 ABOUT TWN4 MULTITECH NANO LEGIC 42 M.....................................................................................................
1 INTRODUCTION 1.1 ABOUT THIS MANUAL This integration manual explains how to integrate ELATEC RFID reader/writer module TWN4 MultiTech Nano LEGIC 42 M into a host device and is mainly intended for integrators and host manufacturers. Before installing the product, the integrators should read and understand the content of this integration manual and other relevant installation documents. The content of this integration manual is subject to changes without prior notice and printed versions might be obsolete.
2 SAFETY INFORMATION • ELATEC TWN4 MultiTech Nano LEGIC 42 M is an electronic component and should be installed exclusively by a trained and • • • • qualified personnel. ELATEC recommends the integrators to follow general ESD protective measures during the installation of TWN4 MultiTech Nano LEGIC 42 M into a host device, e.g. the use of an antistatic wristband or special gloves.
3 INTEGRATION INSTRUCTIONS 3.1 GENERAL TWN4 MultiTech Nano LEGIC 42 M may be installed in any host devices, as long as it is operated under the operational conditions stated in the user manual and other technical documents (e.g. data sheet). 3.2 LIST OF APPLICABLE RULES Refer to the approval certificates, grants and declarations of conformity issued for TWN4 MultiTech Nano LEGIC 42 M, and to Chapter “Compliance Statements” for a detailed list of the rules applicable to TWN4 MultiTech Nano LEGIC 42 M.
3.6 RF EXPOSURE CONSIDERATIONS The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 0 cm and any additional testing and authorization process as required. Refer to Chapter “Compliance Statements” for detailed information about the radio frequency exposure conditions applicable to TWN4 MultiTech Nano LEGIC 42 M. These RF exposure conditions must be stated in the end-product manual(s) of the host product manufacturer. 3.
It is recommended that the host product manufacturer installing the modular transmitter perform some investigative measurements to confirm that the resulting composite system does not exceed the spurious emissions limits or band edge limits (e.g., where a different antenna may be causing additional emissions). Detailed information regarding test procedure are described in the relevant rule parts (refer to Chapter “List of applicable rules”). 3.
4 COMPLIANCE STATEMENTS 4.1 EU TWN4 MultiTech Nano LEGIC 42 M is in compliance with the EU directives and regulations as listed in the respective declaration of conformity. 4.2 FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
5 INTEGRATOR AND HOST REQUIREMENTS Authorization requirements TWN4 MultiTech Nano LEGIC 42 M has been certified as a module and does not need further approval, provided that the module: • is used with antennas as specified in this manual; and • is used in accordance with the FCC grant conditions and no limitations or usage conditions have been defined by ELATEC.
APPENDIX A – TERMS AND ABBREVIATIONS TERM host device Integrator KDB modular type n/a RFID (reader/writer) module SMT THT EXPLANATION Also “host” or “host product”. Device in which an RFID module is intended to be installed for operation. Responsible party for the integration of an RFID module into a host device. The integrator might be the module manufacturer, the host manufacturer, the end user or any other third party.
ELATEC GMBH Zeppelinstr. 1 • 82178 Puchheim • Germany P +49 89 552 9961 0 • F +49 89 552 9961 129 • E-mail: info-rfid@elatec.com elatec.com Elatec reserves the right to change any information or data in this document without prior notice. Elatec declines all responsibility for the use of this product with any other specification but the one mentioned above. Any additional requirement for a specific customer application has to be validated by the customer himself at his own responsibility.
