Transponder Reader TWN4 Palon Compact LEGIC Integration Manual Rev.
Elatec GmbH 1. Introduction The transponder reader TWN4 Palon Compact LEGIC is a device for reading and writing RFID transponders. There are different versions of TWN4 devices available, which cover a large range of transponder types both in the frequency range of 125 kHz and 13.56 MHz. 2. Getting Started 2.1 Cable Connection In order to start operating a TWN4 Palon Compact LEGIC transponder reader, it simply has to be connected to a host. 2.
Elatec GmbH 2.3 Enumeration (USB Only) This is only applicable for the USB version: Once the device has been powered up, it is waiting for completion of the enumeration by the USB host. As long as the device is not enumerated, it is entering a minimum power consumption mode, where both LEDs are turned off. 2.4 Initialization After powering up and enumeration (in USB mode), the device is turning on the built-in transponder reader logic. The green LED is turned on permanently.
Elatec GmbH 2.6 Detection of a Transponder If a transponder is detected by the reader, following actions are performed Send the ID to the host. By default, the USB device sends by emulating keystrokes of a keyboard. A RS232 device sends the ASCII code of an ID.
Elatec GmbH 3.
Elatec GmbH 4. Power Supply In case of USB connection, the input voltage is 4.3V to 5.5V. If the device is supplied via the terminal block, the input voltage is 9V to 30V. 5.
Elatec GmbH 6. External Antenna Please note: Connecting an antenna to the UMCC connector is not included in the approvals of the device. In this case, the device requires separate approval with that specific antenna.
Elatec GmbH 7. Compliance statements 7.1 RF module USA (FCC) (RF module) Compliance statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Elatec GmbH CANADA (ISED) This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
Elatec GmbH 7.2 Host device USA (FCC) FCC notes for a host subject to SDoC: For a host device assembled with the certified module and subject to 47 CFR Part 15, the following statements have to be included in the user manual and the host device has to be labelled as noted below. If the host device is subject to other authorization procedures or parts, the appropriate requirements of these authorization procedures or parts apply.
Elatec GmbH For class B devices: FCC §15.105 (b): Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Elatec GmbH Special accessories: Where special accessories such as shielded cables and/or special connectors are required to comply with the emission limits, the instruction manual shall include appropriate instructions on the first page of the text describing the installation of the device.
Elatec GmbH CANADA (ISED) This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
Elatec GmbH NCC Warning Statement 低功率電波輻射性電機管理辦法 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得 擅自變更頻率、加大功率或變更原設計之特性及功能。 (即低功率電波輻射性電機管理辦法第十二條) 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現 象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受 合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 (即低功率電波輻射性電機管理辦法第十四條) 本模組於取得認證後將依規定於模組本體標示審驗合格標籤， 並要求最終產品平台廠商(OEM Integrator)於最終產品平台(End Product)上標 示 ”本產品內含射頻模組，其NCC型式認證號碼為：CCXXxxYYyyyZzW ”。 應避免影響附近雷達系統之操作。 Page 14 of 15
Elatec GmbH Service Address In case of any technical questions, please contact: Elatec GmbH Zeppelinstr. 1 82178 Puchheim Germany Phone: +49 (0) 89 5529961 0 Fax: +49 (0) 89 5529961 129 Email: info-rfid@elatec.
