EINTLEG INTEGRATION MANUAL
TABLE OF CONTENTS INTRODUCTION .............................................................................................................................................................................. 3 ABOUT THIS MANUAL ...............................................................................................................................................................3 SAFETY NOTES ................................................................................................................
INTRODUCTION ABOUT THIS MANUAL This integration manual explains how to integrate ELATEC RFID module EINTLEG into a host device. This module is not for sale, it will only be used for ELATEC´s own host products. The content of this integration manual is subject to changes and printed versions might be obsolete. As the module manufacturer, ELATEC is responsible for the update, release and publication on the FCC database of this integration manual.
996369 D03 OEM Manual 996369 D04 Module Integration Guide Guidance for Modular Transmitter Instruction Manuals and TCB Certification Application Reviews Modular Transmitter Integration Guide— Guidance for Host Product Manufacturers Laboratory Division Federal Communications Commission Office of Engineering and Technology Laboratory Division Federal Communications Commission Office of Engineering and Technology Laboratory Division For more information about this integration manual or the EINTLEG, go to ww
MECHANICAL INSTALLATION The module can be soldered on a PCB. Abbildung 1: EINTLEG Dimensions ELECTRICAL CONNECTION The EINTLEG module has the following connections: Host interface MOSI/RX MISO/TX nCS/nWAKEUP SCK IRQ/OIF nRESET Config IFMODE0 IFMODE1 HWDET0 HWDET1 GPIO GPIO00 ..
LIST OF ANTENNAS The modular transmitter exclusively uses the chip antenna 450AT18A100 manufactured by Johanson Technology, Inc. This chip antenna is integrated on the modular transmitter board as part of the assembly. For details of the specifications see appropriate data sheet. Using another antenna voids the FCC authorization to operate the modular transmitter.
COMPLIANCE STATEMENTS FCC (RF module) Compliance statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Host devices FCC notes for a host subject to verification or SDoC: For a host device assembled with the certified module and subject to 47 CFR Part 15 verification of class A digital devices, the following statements have to be included in the user manual and the host device has to be labelled as noted below. If the host device is subject to other authorization procedures or parts the appropriate requirements of these authorization procedures or parts apply.
Example for SDoC: The compliance information statement shall be included in the user's manual or as a separate sheet. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form. The information may be provided electronically as permitted in §2.935.
NOTE: The Commission does not have a required SDoC format. This is an example only and is provided to illustrate the type of information that may be supplied with the product at the time of marketing or importation for meeting the FCC SDoC requirement. For class B devices: FCC §15.105 (b): Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
CANADA: This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
SERVICE ADDRESS For information on test modes and additional testing requirements please contact ELATEC GmbH Zeppelinstr. 1 82178 Puchheim GERMANY Phone: +49 (0) 89 5529961 0 Fax: +49 (0) 89 5529961 29 E-mail: info-rfid@elatec.com ELATEC GMBH Elatec reserves the right to change any information or data in this document without prior notice. Elatec declines all responsibility for the use of this product with any other specification but the one mentioned above.