ELAM 12" Touch Panel User Interface Quick Install Guide: EL-ITP-12-BK / EL-ITP-12-WH 16 pages Format: 4.125” wide x 5.75" high English Only Questions? Bergen Schrosder@noriekoonirol.
QUICK INSTALL GUIDE Thank you for including the TIP-12 as part of the user interface strategy for your customer. The TIP-12 has been designed to provide years of trouble frats operation wham wired and Installed properly. The [PT-12 has been designed for Installation In low humidity Indoor environments and should never be Installed outdoors or In high humidity areas.
QUICK INSTALL GUIDE PLANNING THE INSTALLATION The TIP-12 Is design to wall mount In either Portrait or Landscape argumentation. Ensure thees Is adequate wall spas for the [PT-12 and that the surface Is relatively smooth. The TIP-12 requires a minimum mounting depth of 14” (4.5 om} from the front surface plus room for wire. Ensure that adequate depth Is available. Power may be supplied by Power Over Theme (PoE) or by a 12v DC power supply (not Included). PoE must meet the IEEE 802.3af standard.
P12 b. Mounting Bracket @ The TIP-12 has been designed to mount standard 2 gang box or low voltage bracket. . The TIP-12 bracket mounts to the standard 2 gang B box and the [PT-12 snaps Into the [PT-12 bracket. Retrofit Bax Now Construction Trotter Low Low Voltage Bracket Vantage Bracket [ lawnmower ©. Landscape Mounting wr w Install the 2 gang box or bracket In Its normal orientation with mounting craw holes at the op and bottom. u 2 Gang Box d.
QUICK INSTALL GUIDE ®. Installing the TIP-12 Bracket The TIP-12 Includes a mounting bracket that must be used. Using the Included screws, mount the bracket to a standard 2 gang electrical bax ar low voltage bracket and verify that the bracket Is level before tightening the screws. gang Box er 1. Connecting the TIP-12 to Power The PT-12 Is designed to be powered over the Theme connection (PE) or by connecting a 12V DG power supply (not included), but not both.
P12 12V DC Power Supply By using a 12V DC power supply (nat Included) to power the [PT-12 you can provides prows locally or remotely. If powering locally, be sure to run the wire through the wall in accordance with local biking and electrical codes. 1f powering remotely, bi sure to uss wire of adequate gauge for the length of the run, Verify the polarity of your power supply prior to termination and ensure the power supply Is not connected to a power source. Strip approx.
QUICK INSTALL GUIDE 4. Connecting Theme ‘When not using PoE, and you have a physical network connection available tls recommended that you connect the TIP-12 directly to the network switch. Using 2 TSWANA or TS68B watermark cabal, connect to the LAN/POE jack. i you have terminated your own GAT 56/8/7 cable use a tester to ensure that both ends have been property terminated.
h. Mounting the [PT-12 P12 The TIP-12 Is held Into the mounting bracket by with tabs on the rear of the panel. Orient the panel with the camera, microphones, and sensors button at the top for landscape mounting, or the right side for portrait mounting. To complete the installation simply grasp the TIP-12 on the edges and press firmly on to the bracket until It Is settled. CAUTION: DO NOT PRESS DIRECTLY ON THE SCREEN When installing on to the mounting bracket.
QUICK INSTALL GUIDE 2 Powering up the TIP-12 Apply power (12V DG or PoE) and wait for the unit to boot up. H connected to a wired Theme switch tha TIP-12 will acquire a network ‘address via CPD and automatically connect to the system. Ii the TIP-12 does not detect a wired Ethernet connection and the WiFi radio has not bean configured, you will need fo sat up the wireless connection.
P12 3 Startup Settings After applying power to the PT-12, UN-check the Auto Start checkbox then tap the Configure button. From here, you will ses the Startup options: a. Configure WIFI To use WIFE, check the Enable WIFI box, select the SAID and enter the password. b. Orientation Setup Configure whether the panel will be Installed In portrait or landscape mode. Note: Tha TIP-12 Is optimized for use In landscape mods. c. Camera Enable / Disable The TIP-12 camera can be enable or disabled.
QUICK INSTALL GUIDE 4 Reset The recessed RESET button has two functions. Press and hold the button for 3 seconds to reset the panel settings. ‘With the unit powered off, press and hold the button then power the unit ono taser to the factory default configuration. CAUTION: Neither of these actions can be reversed.
P12 5 Removing the TIP-12 Slide the removal key behind the panel taking care to insert in the key ‘channels on the rear of the panel and avoid making contact with the wall, Erase up on the removal key to release tha locking tabs. Once unlocked, pull the bottom of the panel away from the wall, then pull aut.
LIMITED WARRANTY Norther Security & Control ( ‘NSC’ } warrants the TIP-12 ta be free farm defects In materials and workmanship for the peeled of two years (2 years) from the date of purchase. If within the ‘applicable warranty period shove purchaser discovers that such tem was not as warranted above and promptly notifies ‘NSC’ In writing, "NSC" shall repair or replace the fem at the company's option.