Intelligent Management Thermal Imaging & Face Recognition Terminal User Manual Model： EKIAD070
Catalog PRODUCT OVERVIEW .......................................................................................................................................... 1 1. 1.1. 1.2. PRODUCT INTRODUCTION ..................................................................................................................................... 1 PRODUCT CHARACTERISTICS ................................................................................................................................ 1 2.
FUNCTIONS OF MANAGEMENT SYSTEM................................................................................................... 28 6.8. 6.8.1. IN AND OUT ANALYSIS .............................................................................................................................. 28 6.8.2. STRANGER CAPTURE ................................................................................................................................. 29 6.8.3. DOORBELL CAPTURE ..............................
1. Product Overview 1.1. Product Introduction Based on infrared thermal imaging technology, imported sensor is used to support face recognition, body temperature measurement, and upload captured pictures to the management platform. After face recognition passed, the access control function would be activated. The high temperature warning value can be preset, a warning window will pop up when high temperature is detected, and the captured picture will be uploaded to the platform.
⚫ ROM: 8GB eMMC. ⚫ OS: Embeded linux os,or Android (Confirm when ordering). ⚫ I/O port: 485 output, relay output; WG output is customizable. ⚫ Communication: wired or wireless network(Confirm when ordering). ⚫ Power input: DC 12V. ⚫ Work temperature: 0℃ - 50℃ (For temperature measurement), -10 ℃ - 50℃(Only for Face recognition). ⚫ Work humidity: <90% RH. ⚫ work environment: indoor, no wind, no direct sunlight.
sunscreen shed. Ensure that there is no object with high heat source and strong sunlight within the detection range of the probe, including but not limited to direct sunlight, metal roof, etc. ⚫ It is recommended to use Google browser to access the platform management system. 3. Equipment wiring diagram 3.1.
Wiring harness 3.2.
3.3. How to control gate lock 3.4. If used to check body temperature only If used to check body temperature only (Factory default operating mode), just connect DC Power. If you want to view records in real time or export all records, you should connect to the LAN of your company. The default IP address of device is 192.168.1.249/255.255.255.0.
4. Local setting on the device 1. Click 3 times in the lower left corner of the device screen to display the bottom menu. Click the bottom menu, choose “Password”. 2. Click "Password", and input 666888#888888# to enter the device parameter setting interface. 3. After entering the setting interface, select the corresponding function options of the left menu bar to set the relevant parameters, click the left menu to select, and swipe the right option to switch. 4.
5. if you want to set the temperature calibration mode, select “system” in the left menu bar, and then select “UI”, find “temperature calibratio”. After your choice, click the “Save” button. 6. Other parameters can be set according to the menu bar instructions.
5. Independent use without platform 5.1. Open local service 1. This function is faster and more convenient for local deployment of customers, solves the problems of difficult wiring and network environment protection, and is completely independent of the platform function and does not affect each other. (only version 4.53 and above is supported) 2. Enter local setting interface, select system->External, and find "local service", set to open and Save.) 3.
4. View record in real time: after login into the device , you will view all records, including the in and out records of body temperature detection in real time. 5. Record export: in the upper right corner of the interface, click the button to pop up the time interval selection box, click the Export button, select the time interval, and export the corresponding records. (the default retention policy of the device is: keep the records of the last month, and keep 500m pictures (about 8500).
5.2. Modify Machine’s IP After the device is powered on and networked, open the "vCard device configuration tool" and click the "search" button to search. (the default network segment of the device is 192.168.1. X, if you can't find the IP address, please change the computer to the corresponding network segment first.) The default IP of the device is 192.168.1. 249.(mask 255.255.255.
5.3. Configure WiFi In "vCard device configuration tool", select "specific device functions" in the lower right corner, select "WiFi configuration", enter the SSID and password of WiFi in the pop-up window, and click "confirm" to configure WiFi. The device will automatically get the IP address.
5.4. Check whether the device is online After the IP modification of the device is completed, check whether the device is connected to the network normally. Dobule click the lower left corner of the face recognition machine interface to check the operation status parameters of the device, check whether the "status" is online, and "online" means the device is connected to the network normally. 6. Use under support of management platform 6.1.
(if there is no platform account, please click "register account" to register. Enter the company name, mobile number (management account), password and confirm password to register. Click "register" to confirm. 6.2.
6.3. Add Device Select the left menu bar, click "Device manager" - " Device list" - "add device ", enter "Device Num" ( very important), fill in other relevant information freely, and then click "Submit" to add. How to obtain the device number: open the "vCard device configuration tool", click "search", after the device list appears, pull the scroll bar to the right at the bottom, find the "hardware ID" list, and copy it.
6.4. Observe device status After the equipment is added, observe the "device status". When the device status is "online", the equipment can be configured. If the device status is offline, please refresh the browser several times or log in to the platform again. If the device displays "offline" all the time, please check whether the status of the machine’s interface is "online". Offline reason: the device is not connected normally or the platform needs to be refreshed.
6.5. View records in real time. After logging into the cloud platform, open the web page and input "http://admin.erpaier.com: 22345 / # / vCard / bigdata" to view the in and out records of body temperature detection in real time. 6.5.1. Record query 1. Pass (body temperature) record, including personnel information, body temperature information and snapshot pictures reported by each device. 2. Click the corresponding record list to display the record details.
6.5.2. Record export After clicking “expand”, the access time will appear. Select the time period to export records. After clicking export, the corresponding data table will be downloaded. (some browsers may block the redirection window. In this case, if you cannot download the report, you need to close the browser's blocking settings.
6.6. Main parameter setting 6.6.1. Enter parameter setting Find the corresponding equipment list, click the corresponding "hardware ID" to enter the device parameter setting interface. 6.6.2. Set pass mode "Full open" mode is on: only body temperature is detected, and face recognition is not performed. "Full open" mode off: face recognition + body temperature detection is required for passing. After entering the parameter setting interface, click "System settings" and pull down the scroll bar.
6.6.3. Thermal imaging emissivity 1. Thermal imaging emissivity: adjust the accuracy of body temperature detection (tune number less if temperature is lower, and tune number more if temperature is higher. 850-1000 recommended). The thermal imaging emissivity shall be fine-tuning tested according to the actual application environment until the value is normal.
2. After entering the parameter setting interface, pull down the scroll bar to find the " External settings", click to enter, first click "get", after obtaining the device parameters, find "radiation rate of thermal imaging module", then modify the parameters, and finally click "Set" to save. 6.6.4.
Model 2: suitable for the scene with large interference Model 3: coarse precision model, can not be used for parameter optimization. This model should be selected after the parameters has been adjusted. Customers need to choose the best according to the actual scenario and test results. By default, the machine uses the coarse accuracy mode, which is compatible with the human body temperature detection of each scene.
6.6.5. Face comparison score threshold 1. Face contrast score threshold: affects face recognition value, such as wearing mask recognition, can be adjusted down appropriately. (recommended 75-90) 2. After entering the parameter setting interface, pull down the scroll bar to find the "face recognition parameters", click to enter, first click "get", after obtaining the device parameters, find the "face comparison score threshold", then modify the parameters, and finally click "set" to save.
6.7. Secondary parameter setting 6.7.1. Temperature check mode There are four modes: Shutdown: doesn’t detect and check body temperature. Body temperature alarm: detect body temperature, and when the body temperature exceeds the high temperature threshold, alarm the abnormal body temperature. Exception does not unlock: detect body temperature, and when the body temperature exceeds the high temperature threshold, the machine won’t send signal to open door.
6.7.2. Temperature alarm threshold Temperature alarm threshold: alarm when the temperature threshold range is exceeded. (35.5 ℃ ~ 37.3 ℃ is recommended by default) After entering the parameter setting interface, pull down the scroll bar, find and select "External settings", first click lower left "get" to get the device parameters, then find "low temperature threshold" and "high temperature threshold" after obtaining the device parameters, then modify the parameters, and finally click "set" to save.
6.7.3. Low temperature traffic mode 1. No access at low temperatures: when detect low temperature, the device won’t send signal to open door. 2. Low temperature allows pass to broadcast actual temperature: when detect low temperature, the device send signal to open door and broadcast actual temperature. 3.
6.7.4. Broadcast temperature value switch 1. Close: only indicates that the temperature is normal, and does not broadcast the specific temperature value. 2. Open: prompt that the temperature is normal, and broadcast the specific temperature value.
6.7.5. Upload stranger record 1. Stranger face recording switch: ①Open: stranger passes, upload access record to platform ② Close: stranger passes, do not upload access record to platform. 2. Stranger face record upload interval: 10s by default. (setting interval 1-10) 3. Stranger face record upload mode: ① fixed interval: set to this parameter, and the parameter " Stranger face record upload interval" will take effect. ② Continuous masking: do not upload stranger records. 4.
6.7.6. Mask alarm Mask reminder: ① Open: alarm if the passers-by doesn’t wear mask; ② Close: do not identify the mask After entering the parameter setting interface, pull down the scroll bar to find the "face recognition parameters", click to enter, first click "get", after obtaining the device parameters, find "mask reminder", then modify the parameters, and finally click "set" to save. 6.8. Functions of management system 6.8.1.
6.8.2. Stranger capture After the device starts the stranger capture upload, all stranger capture information of each device will be shown. It supports querying any snapshot according to the device and time period.
6.8.3. Doorbell capture When doorbell capture is set on, the device will take a picture of the visitor and upload it when the doorbell is pressed. 6.8.4. Area manager By setting the mobile phone of the person in charge of the area and corresponding to the mobile phone number bound with wechat, wechat message notifications of the device can be received.
6.8.5. Organization management Personnel management is available. New personnel can be added through personnel management. Personnel information can be imported in batches and faces can be uploaded in batches. 6.8.5.1. Add personnel information Select Organization->People List, and click “+Add People” to add one by one, click “+Batch Import” to add peoples in batch.
6.8.5.2. Face uploading 1. Upload one face: click the corresponding "face" head image, and select the corresponding face photo after pop-up. (Photo format: less than 1m, JPG format) ("face" refers to the face image uploaded through the management platform, "sub face" refers to the face image uploaded by the end user through the applet.) 2. Upload faces in batch: ① After the face photos are named according to the rules, they are uniformly compressed into a zip file, with each package no more than 50m.
② Put the compressed file in a folder, and select the folder when uploading. ③ Click the "upload face in batch" button, and select the folder where the face photos need to be uploaded. Naming rules for face photos: Naming rules for face photos viewed through system settings - subject settings) is 1, and the person number is 2020, so the corresponding face picture name can be: 1_2020.jpg Naming rules for sub face photos 6.8.5.3. Subject-ID_Person-Number.
6.8.5.4. Department management Department management is used for the management of personnel information in different departments. Through the mobile phone of the department head and the corresponding mobile phone number bound with wechat, you can receive the wechat message notification of the access (temperature) data of personnel under the corresponding department.
6.8.6. Log list "Log list": you can view the records of various operation steps, check the success of parameter distribution, face authorization, etc.
6.8.7. User management "User management": multiple sub users can be added to help management.
7. System upgrade of the device 7.1.1. Local upgrade Open "vCard device configuration tool" - click "display advanced settings" - click "upgrade" - click "load upgrade package" - select upgrade file - display "loading succeeded" later - check the corresponding device - click "upgrade" to upgrade. 7.1.2.
8. Third party access 8.1. Third party platform address 1. Third party address: the address of the third party can be set as the address of the user platform. After the setting is successful, the traffic (body temperature) is recorded, and the device log will be actively sent to the user platform through the address. (it is used for the customer docking equipment protocol with development ability, and the address here can be modified as the customer platform connection address.) 2.
8.2. Change logo 1. Start screen: the static picture displayed at startup, format: BMP, resolution: 480 * 854, file size: unlimited. 2. Power on animation: accept the start screen. Format: BMP, GIF, avi, resolution: 480 * 854, file size: unlimited. 3. Screen saver animation: during the operation of the machine, in the idle state, the displayed screen is in the format of BMP, GIF, avi, resolution: 480 * 854, file size: unlimited.
9. Deployment scenario 9.1. Distance It is recommended to draw a yellow line on the ground, 0.3-1m away from the device.
FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
