MPL-3222 English Media Player / Digital-signage Installation Instructions Before connecting, operating or adjusting this product, please read through these instructions completely. Please keep this manual for future reference.
1. Safety Precautions WARNING • • • • To avoid fire, electric shock or failure never attempt to disassemble or modify this product. If you sense smoke, odd odors, or unusual noises while in operation, immediately unplug the display from the power source. Switch off and unplug the plasma display from the supply outlet. To avoid fire or shock, do not leave the power of the display turned on. To avoid shock or other problems, do not leave the display plugged into the supply outlet.
• Select the appropriate jumper setting to match the resolution of your display. Note: 1024x768 or 1366x768 is set on SD/HD; 1920x1080 is set on FHD.
Insert Board in this direction After Board fully inserted Remove the slot cover by removing the screws Insert the Media Player until it is firmly plugged into the connector. Tighten screws in order 1 - 4 Remove the securing screws. Grip the handle of the terminal board; and slowly pull out in the direction of the arrow • • • Affix the Slot function label if necessary Make sure that the Media Player does not ride on the tower claws. Be sure to fasten all screws tightly.
. Operation Guide Overview Full HD Digital Media Player plug-in board provides playback for a wide range of SD & HD video up to 1080p, audio and high-resolution image media types onto the professional displays with native FHD resolution and astounding video quality. Premium contents that comes with raw digital audio surround sound can utilize the coaxial digital audio output to deliver true 5.1 or multi-channel surround sound profile to an external AV receiver.
LVDS provides the uncompressed video signal directly to the video panel driver with unparalleled qualities to digital video. MPL3222 HD can be networked with a PC using its built-in LAN port. You are able to stream files from a PC and play the file on the display. With two USB host ports, you can now attach additional external USB Thumb drive, USB Multi-Reader, powered USB hard drives. You can also playback files from the USB connection of a digital camera, PDA, Hand Phone or MP3 player.
Remote Control Tour A. POWER (Standby) Power on/off the device B. ALPHA NUMERIC INPUT Enter numbers for Setup options C. CLEAR Delete the characters immediately before the cursor D. E. MUTE ON/ OFF Mute volume of device on/ off REPEAT Enable Repeat Function Loop: Repeat Off, Repeat One, and Repeat ALL (Repeat STBY when Playlist Mode) F. RETURN G. VOLUME (+,-) Return to last step Increase/ Decrease the volume H. OK Activate selected items I. DIRECTIONAL KEYS J. REVERSE K.
Playing Video, Music & Photo After turning on the power to the display, a home page will appear with the following options: IP STREAMING, AUDIO, VIDEO, PHOTE, PLAYLIST and SETUP. ‘VIDEO’ is automatically selected as the default. Playing Media Files 1. Use the directional buttons to move selector to “Media Type” button on screen and press from the remote control. The below page will be displayed on the screen, Sources are: USB-1 disk, USB-2 disk or SD card.
2. Use to select the source/file, press as shown in below image: to enter “SD Card”, “USB 1” and so on listed 3. The file names of the media will be displayed on the screen, if the file type matches the type indicated on the left side. Note: When navigated from video, only the video files can be seen. If navigated from other file types (for example, audio or photo), only the matched file type will appear. 4. To play: Move the selector to the file, Press .
5. Repeat function in Playing Media Mode: Pressing the repeat button once Pressing the repeat button twice list. Pressing the repeat button third REPEAT ONE will repeat the playback of current video file once. will result in repeated playback of all videos in the → → → will result to cancel repeat status. REPEAT ALL REPEAT OFF 6.
Playing Video Files From the menu, browse to the Video folder and click from remote control. Press Play button from the remote control to play. Playing Music Files English From the menu, browse to the Audio folder and click from remote from the control. Press Play button remote control to play music files.
IP Streaming MPL3222 also supports multicast streaming over the network. It acts as a receiver and currently supports up to a maximum of 10 streams: All the settings for the streams that appear on the screen are hard coded. IP Stream 01 fixed Multicast IP is 224.1.1.1:1234 IP Stream 02 fixed Multicast IP is 224.1.1.2:1234 IP Stream 03 fixed Multicast IP is 224.1.1.3:1234, etc.
Playlist 1.
1. To create a new playlist, move the selector to “CREATE NEW” and press . New playlist created will be called “PlaylistX.pst”, repeat to create more Playlists. 2. To delete an existing playlist, select the playlists by pressing . Once selected, a will be marked beside the selected playlist. You can select multiple playlists. Move the selector to “DELETE”, press to delete all selected playlists. Once the delete option is selected, the files will be permanently deleted.
3. To Edit playlists, move the cursor by right navigation key Icon to one of the PLAYLIST file name with .plst extension. 4. To insert media to the newly created Playlist, navigate Media’ button and press from the remote control.
5. On the next screen, select the source from where the media is located. The below image shows the attached USB disk. Navigate to the video files that have to be added and press the select button from the remote control, a will be displayed next to the video file. Once the selection of video files is complete, navigate the cursor by to the OK button on the screen and press from the remote control to confirm the operation, or to cancel button on screen to discard the operation. 6.
7. To add more media to existing (or any other) playlist, repeat the above steps. Note: Only video files can be added to a playlist. 8. Once it has been done, move to “save” button then Press changes made to the playlist.
Popup Popup is a list which allows you to popup other narrow banners on screen to overlap the video on screen from top / bottom or left / right side. Described below are the instructions on how to create/delete and edit a popup. 1. Go to Playlist from the home page, move to the Popup List button and press 2. There is no popup list available and you will have to create new popup list . Navigate to the “Create New” button and press from the remote control.
3. Contents can be added to the popup once it has been created. Navigate the selector to the desired popup and press from the remote control. On the left of the popup editor, available buttons are: “Insert Banner”, “Move Up/Down”, “ Select All”, “Clear Selection”, “Remove” , “Save” and “Cancel” shown in the below image: 4. To insert banner files to the newly created Popup, navigate to the Insert Banner button and press from the remote control.
5. Navigate to the banner files to be added and press Select button from will be marked next to the banner file. Once the selection the remote control, a of banner files are completed then with the help of the navigation keys navigate to the OK button on screen and press from the remote control to confirm the operation. 6. To cancel, press the cancel button to discontinue operation.
7. In the Popup browser there are Duration and Position need to be set: Duration available range: 10 ~ 120 seconds; Position available range: Top & Bottom (for vertical images) or Left or Right (for a horizontal image); Once the popup is populated with the desired banners, navigate to the Save button follow by to save the changes as shown in the image below: Note: Banners can only be set in Vertical (Left or Right) position or in Horizontal (Top or Bottom) position.
11. An inserted popup will appear in all the video files that are scheduled to play after the inserted popup. 12. If you want to stop a popup from appearing on a video, insert a new popup at the location where you want the popup to stop. In this way the inserted popup will not run any more on the clips that follow. 13. Once it has been done, do not forget to save the changes made to the playlist. Marquee Marquee is an editable text banner displayed on top or bottom of the screen.
3. To insert text to the newly created marquee navigate to the edit option and press “Edit” button from the remote control. With the help of the alpha numeric keys of the Remote Control, type in the text for the marquee. Use “Clear” to backspace for texts correction. Press to finish editing. 4. There are Duration and Position of the marquee need to set: Duration can be set at: 10 ~ 120 seconds Position can be set at: Top & Bottom. All Rights Reserved Eins Technology 23 English 2.
Once the marquee is populated with the desired text, navigate to the “Save” button on the left to save the changes. 5. Once the marquee is populated, it can be added to a video files in a playlist. To add a marquee to a video file in the playlist, go to Playlist, navigate to the desired playlist and press from the remote control. On the left of the playlist editor, button is available to “Insert Marquee”, click and it will show the list.
Setup Navigate to “SETUP” on home page and press on remote control. Or press the Setup button on the remote control to invoke the setup option A: Setup: Output Mode: Automatically detects the display i.e. the display is SD/HD or FHD, and selects the appropriate option Slideshow Duration: Slideshow duration could be set to 5, 10, 15, 20, 30, or 60 seconds. Background Music: Enable or disable the background music while a slideshow is running.
Background Photo: Enable or disable the background image while listening to the music. Expand background photo option to browse and associate default photos while listening to music. B: Network: Second step is to configure the network IP address settings so that you could be connected to the local area network (LAN) to access the contents from the PC(s) over the local area network. LAN IP address connection settings could be configured with fixed IP Manually or Auto IP from DHCP.
Upgrading new firmware to the ROM is a breeze & it’s just a click away. When in the Setup screen navigate to Update ROM page. On the bottom right corner, current version of the installed firmware will be displayed. New firmware should be stored at the root directory a USB storage device (USB thumb drive or USB HDD). With the USB storage device attached to the USB port and browsed, press the Update ROM button at the bottom of the screen and ROM update will start automatically.
Specifications SYSTEM HD Video Playback HD Video Resolution Media Processor CPU / System Board AV OUTPUT Video output Audio output MEDIA FORMAT Video Format Audio format Image Format TV System RESOLUTION Multiple Digital Output Resolution Video Resolution Multiple Component Resolution Picture Resolution CONNECTIVITY Network USB Interface USB Classification English USB device VC-1(WMV9 MP@HL), MPEG-2 MP@HL(720p/1080i), DivX HD, MPEG4 H.