Owner's Manual

EFXAKCMBB
EFXAKCM10B
MOTORCYCLE AMP WIRING KITS
PARTS LIST
EFXAKCMSB
• In-line 8/10 AWG Waterproof fuse holder
(Pre-attached to power cable)
• (6ft) 8AWG Red + (6ft) 8AWG Black with protective
braided sleeve, heat shrink and Ring terminals
pre-attached
• (2) 4ft, 16AWG EFX Speaker wire with protective
Braided aleeve and heatshrink
• (3ft) 18AWG Blue Remote turn-on wire pre-attached
with male disconnect
• (2) 8GA Spade terminals (Red, Black PVC boots)
• (1) 18-22GA Red spade terminal
• (1) 18-22GA Red butt connector
• (4) 14-16GA Blue speaker spade terminals
• (4) 14-16GA Blue speaker speaker disonnect
terminals
• (1) 4" x
6" velcro, adhesive mount pad for amplifier
•
(1 0) 8" cable ties
• (1) 60A mini-ANL Fuse
• (2) 4 7 -Ohm 1 /2W Resistors for bikes with Harman
Kardon Audio ONLY
• 2mm
I 3mm Hex wrenches (for fuse holder)
• Instructions
EFXAKCM10B
• In-line 8/10 AWG Waterproof fuse holder
(Pre-attached to power cable)
• (6ft) 1
OAWG Red + (6ft) 1 OAWG Black with protective
braided sleeve, heat shrink and Ring terminals
pre-attached
• (2) 4ft, 16AWG EFX Speaker wire with protective
Braided aleeve and heatshrink
• (3ft) 18AWG Blue Remote turn-on wire pre-attached
with male disconnect
• (2) 1
OGA Spade terminals (Red, Black PVC boots)
• (1) 18-22GA Red spade terminal
• (1) 18-22GA Red butt connector
• (4) 14-16GA Blue speaker spade terminals
• (4) 14-16GA Blue speaker speaker disonnect
terminals
• (1) 4" x
6" velcro, adhesive mount pad for amplifier
•
(1 0) 8" cable ties
• (1) 30A mini-ANL Fuse
• (2) 4 7 -Ohm 1 /2W Resistors for bikes with Harman
Kardon Audio ONLY
• 2mm
I 3mm Hex wrenches (for fuse holder)
• Instructions
NOTES: READ FIRST!
This kit is designed for upgrading or expanding the factory audio system on many 1996 and later bagger HD models
including FLHT, FLHX, FL TR and some TRIKEs. Use this kit to install a single (small form factor), weather resistant
amplifier that is suitable for motorcycle applications (Amp not included)
This kit may also be adapted to other makes
with a 12V battery and stereo source unit. Depending on the particular type of stereo, additional Audio interconnect(s)
may be needed for signal connection between the source unit and the amp.(lnternconnects sold separately).
TOOLS & PREPARATION
This manual is intended as a guide to installing the included items. When possible, refer to the factory service manual
for your specific year make and model for additional techinal information. If you are unsure, or do not have the ability to
access the battery, remove the fairing, and route cabling under the gas tank, the we recommend professional
installation. The following is a list
of common tools and supplies required when performing this installation:
• SockeURatched set, Standard • Allen Hex sockets or wrenches, Standard • Screwdrivers
• Wire stripper • Wire crimper • Electrical Volt-Ohm meter
• Soft protective cloth covers for painted surfaces • Eye and skin protection
BEFORE BEGINNING:
1. Review this guide thoroughly to become familiar with this kit.
2. Seat and Front fairing (at minimum) must be removed to properly install this kit. Gas tank must be lifted or removed to
access the existing wiring loom or wire trough underneath. (Refer to the factory service manual whenever possible for
removal procedures specific to your year/model).
3. Lay out all neccassary items and plan your installation before beginning.
4. Route the included power/ground cable with existing Factory wires. Use the protective wiring channel if equipped.
5. Keep new wiring away from all moving parts, suspension travel movement or sources of extreme heaUmoisture.
6. (1 0) cable zip ties are included ties to securely fasten wires and cable out of harms way.
7. Work in a clean, dry and level environment.
8. Fuse is not installed in fuse holder from factory. Do not install fuse until the final stage if installation.
9. Turn OFF iginition switch*. (*If equipped with a factory HD security system, hands-free FOB should be present.)
©2015 SCOSCHE INDUSTRIES, INC.
Sl 300022EFXAKCM88/M10B 04/15