Office +1 Инструкция по быстрой установке 11-2020 / v1.
I Сводка и напоминание 1. Вы можете найти все документы, видео и прошивки: www.edimax.com/edimax_pro/download/Office1-2-3 2. Полная презентация системы Office 1-2-3 вы можете найти: http://office123.edimax.com 3. В системе может быт только ОДИН мастер Office 1-2-3 ТД. Все другие точки доступа должны быт Office +1. 4. Во время начальной настройки, Мастер ТД автоматически настроит все точки доступа Office +1. Это займет около ~10 minutes. 5. По умолчанию логин и пароль admin и 1234.
II Информация о продукте II-1 1 Комплект поставки 3 2 6 5 4 7 1. 2. 3. 4. 8 Office +1 Точка доступа Модуль потолочного монтажа Модуль Т-образного монтажа и набор болтов. CD 5. 6. 7. 8.
II-2 Системные требования - Существующий кабельный маршрутизатор (модем).
II-4 LED Status Цвет индикатора Голубой Желтый Нет II-5 LED Статус Горит Медленно мигает Быстро мигает Горит Мигает Не горит Описание Точка доступа включена. Обновление встроенной программы. Сброс в заводские настройки. Идет запуск. Ошибка Точка доступа отключена. Кнопка Reset Если у вас возникли проблемы с точкой доступа, вы можете сбросить настройки в заводские. При этом будут установлены все настройки по умолчанию. 1. Нажмите и удерживайте кнопку reset не менее 10 секунд.
III Добавить ТД Office +1 в систему Office 1-2-3 Эта инструкция как быстро добавить ТД Office +1 в систему Office 1-2-3. 1. Подключите ТД к PoE коммутатору через сетевой кабель. Если надо, пожалуйста снимите крышку с нижней стороны точки доступа. Это создает дополнительное пространство для прохождения кабелей. 2. Мастер ТД автоматически начнёт передачу настроек к ТД Office +1. Приблизительно за 10мин (~10 minutes), все настройки будет готовы у ТД Office +1. 3.
IV Замена Мастер ТД NOTE: В системе может быт только одна Мастер ТД. Пожалуйста примените эти настройки только тогда если мастер ТД не работает. Этом разделе поэтапная процедура, которая поможет вам заменить оригинальную главную точку доступа, где вы будете обновлять прошивку Мастер ТД, а затем восстановить ранее сохраненные системные настройки. Пожалуйста, убедитесь, что у вас есть: - Прошивка Мастер ТД (можете скачать из сайта Edimax website) - Настройки Мастер ТД (нужна регулярно сохранять копии) 1.
2. Выберите вашу Office +1 AP нажмя “Discover” finder. 3. Нажмите на IP адрес точки доступа для ввода веб интерфейс настроек.
Вас попросить ввести логин и пароль, логин: admin, пароль: 1234: Вот так выглядит веб интерфейс пользователя: 8
4. Нажмите “System Settings” и пройдите в другой раздел для установки. Обновление прошивки 5. Пройдите в низу доя меню Обновление прошивки “Firmware Upgrade”. Если вы еще этого не сделали, перейдите по ссылке URL ниже, чтобы загрузить новейшую прошивку Master: www.edimax.com/edimax_pro/download/Office1-2-3 Найдите прошивку Master и нажмите на значок загрузки, чтобы загрузить. 6. Нажмите “Выберите файл” . 7. Нажмите Обновить “Update” для обновление прошивки на прошивку мастер ТД.
Нажмите “OK” чтобы продолжит. Система обновить прошивку, подождите… 8. После обновления прошивки система предложит вам ввести имя пользователя и пароль, введите их (имя по умолчанию: admin, пароль: 1234), чтобы продолжить: 9.
Нажмите “OK” чтобы продолжит Теперь система перезагружается, подождите … 10.
11. Нажмите на икону “Настройки системы”. Востановить преведущие настройки 12. Выберите восстановление настроек“Restore Settings”. 13. Выберите “Выбери файл” кнопку и найдите файл с преведущеми настройками. 14. Нажмите «Восстановить», чтобы заменить текущие настройки. Если ваш файл настроек зашифрован с паролем, установите флажок «Открыть файл с паролем» и введите пароль в следующем поле.
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment. EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, 2014/35/EU. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2014/53/EU, 2014/35/EU. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2014/53/EU, 2014/35/EU.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European Radio Equipment Directive. Equipment: AC1300 DBDC Ceiling-mount AP Model No.: Office +1 The following European standards for essential requirements have been followed: Directives 2014/53/EU Spectrum EMF : EN 300 328 V2.1.1 (2016-11) EN 301 893 V2.1.1 (2017-05) : Draft EN 301 489-1 V2.2.1 (2019-03) Draft EN 301 489-17 V3.2.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.