Office +1 Schnellinstallationsanleitung 11-2020 / v1.
I Kurze Zusammenfassung und Erinnerung 1. Sie können alle unterstützenden Dokumente, Videos und Programme finden unter: www.edimax.com/edimax_pro/download/Office1-2-3 2. Die vollständige Systemeinführung in Office 1-2-3 finden Sie unter folgendem Link: http://office123.edimax.com 3. Im Netzwerk darf es nur eine Office 1-2-3 Master-Einheit geben. Rest ist dann Office +1. 4.
II Produktinformationen II-1 1 Verpackungsinhalt 3 2 6 5 4 7 1. 2. 3. 4. 8 5. 6. 7. 8.
II-2 Systemanforderungen - Vorhandenes Kabel/DSL-Modem & Router. - Bestehender PoE Switch, der mit dem Router verbunden ist - Computer mit Web-Browser zur Access Point-Konfiguration II-3 Hardwareübersicht C B A D A B C D 12V DC IN LAN 1 (PoE) LAN 2 Reset 12V DC-Anschluss für das Netzteil LAN-Port mit Power over Ethernet (PoE) EIN LAN-Anschluss Setzt das Gerät auf Standardwerkseinstellungen zurück.
II-4 LED-Status LED-Farbe Blau Gelb Aus II-5 LED-Status An Langsam blinkend Schnell blinkend An Blinkend Aus Beschreibung Der Access Point ist an. Firmware wird aktualisiert. Werksstandardwerte wiederherstellen. Gerät wird gestartet. Fehler. Der Access Point ist aus. Reset Wenn Sie mit Ihrem Access Point auf Probleme stoßen, können Sie das Gerät auf die Werksstandardeinstellungen zurücksetzen. Damit werden alle Einstellungen auf die Standardwerte zurückgesetzt. 1.
III Office +1 AP zu Office 1-2-3 hinzufügen Diese Schnellkonfiguration leitet Sie an, wenn Sie Office +1 AP zu Ihrem vorhandenen Office 1-2-3-Hochgeschwindigkeits-WLAN-Netzwerk hinzufügen wollen. 1. Finden Sie den PoE-Switch, der mit Ihrem vorhandenen Office 1-2-3-Netzwerk verbunden ist. 2. Verbinden Sie den Office +1 AP mit Hilfe eines Ethernet-Kabels mit dem PoE-Switch.
IV Austauschen des Master-APs HINWEIS: Es darf in Ihrem Netzwerk nur EINEN Master-AP geben. Verwenden Sie dieses Verfahren nur, wenn Ihr Master-AP ausgefallen ist und ersetzt werden muss. Dieser Abschnitt erklärt schrittweise, wie Sie den ursprünglichen Master-AP ersetzen, auf dem Sie auf die Firmware des Master-APs aktualisieren, und wie sie anschließend die zuvor gespeicherten Systemeinstellungen wiederherstellen.
Wenn Sie das IP Finder Tool nicht öffnen können, finden Sie weitere Informationen im mitgelieferten IP Finder-Dokument in der Office 1-2-3 Kit Box oder im Office 1-2-3 Benutzerhandbuch. 2. Lokalisieren Sie Ihren Office +1 AP, indem Sie auf „Discover” auf dem IP Finder klicken. 3. Klicken Sie auf die IP-Adresse des Access Point, der zum Master-AP werden soll, um in die Web-Benutzeroberfläche zu gelangen.
Bei Aufrufen der Webseite sollten Sie aufgefordert werden, den Benutzernamen und das Kennwort einzugeben, geben Sie sie ein (standardmäßiger Benutzername: admin / Kennwort: 1234) um fortzufahren: Die Webinterface wird unten dargestellt: 8
4. Klicken Sie auf das Symbol für „Systemeinstellungen“. Aktualisierung der Firmware 5. Scrollen Sie nach unten bis zum Seitenende zu „Firmware Upgrade“. Falls noch nicht geschehen, gehen Sie zu folgendem URL-Link, um die neueste Master-Firmware herunterzuladen: www.edimax.com/edimax_pro/download/Office1-2-3 Suchen Sie die Master-Firmware und klicken Sie zum Herunterladen auf das Download-Symbol. 6. Klicken Sie auf „Choose File“ (Datei auswählen), um die Datei mit der Master-Firmware auszuwählen. 7.
Wenn eine Erinnerungsmeldung erscheint, klicken Sie zum Fortfahren auf „OK”. Das System wird aktualisiert, bitte warten Sie... 8. Nach dem Firmware-Upgrade werden Sie aufgefordert, den Benutzernamen und das Kennwort einzugeben, geben Sie sie ein (standardmäßiger Benutzername: admin / Kennwort: 1234) um fortzufahren: 9.
Wenn eine Systemmeldung erscheint, klicken Sie zum Fortfahren auf „OK”. Das System wird jetzt neu gestartet, bitte warten Sie... 10.
11. Klicken Sie auf das Symbol für „Systemeinstellungen“. Frühere Einstellungen wiederherstellen 12. Scrollen Sie nach unten bis zu „Firmware Upgrade”. 13. Klicken Sie auf die Schaltfläche „Choose File“ (Datei auswählen), um eine zuvor gespeicherte Einstellungsdatei auf Ihrem Computer zu finden. 14. Klicken Sie auf „Restore” (Wiederherstellen), um Ihre aktuellen Einstellungen zu ersetzen.
COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd. Edimax Technology Co., Ltd.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment. EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom.
EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, 2014/35/EU. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 2014/53/EU, 2014/35/EU. Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 2014/53/EU, 2014/35/EU.
Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European Radio Equipment Directive. Equipment: AC1300 DBDC Ceiling-mount AP Model No.: Office +1 The following European standards for essential requirements have been followed: Directives 2014/53/EU Spectrum EMF : EN 300 328 V2.1.1 (2016-11) EN 301 893 V2.1.1 (2017-05) : Draft EN 301 489-1 V2.2.1 (2019-03) Draft EN 301 489-17 V3.2.
Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions.