Print Sir Plus PS-3100+ Series 3-Port 10/100Mbps Desktop Print Server User’s Manual BW Hardware Installation MW Features and Specifications
FCC COMPLIANCE STATEMENT This equipment generates and uses radio frequency energy and if not installed and used properly. that is. in strict accordance with the instructions provided with the equipment. may cause interference 10 radio and TV reception. The equipment has been tested and found © comply with the limits for a Class B computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules.
B Hardware Installation Thanks for purchasing this Fast Ethernet Print Server PS-3100+. This guide explains its external features. explains how to unpack your Print Server hardware. and tells how you can connect if to your printer and to your network, Requirements To use your PS-3100+. you will need : + Printers with para lie interface. + Ethernet network cabling, as well as a free abase-T hub: or Fast Ethernet network cabling. as well as a free [abase-TX hub.
LED Indicators The PS-3 100+ is equipped with five LED indicators that show its current status. and can be used for diagnosing problems on the network and the PS-3100+ itself © 10/100MbpS 3-port Print Server ® SCOMDESRNKIACT ® -ovpuinwact @ + Status LED (green) The Status LED is lit © 1. When the Print Server is powered on. When power is applied to the Print Server, it performs a Power-On Self Test (POST). When the self-test is complete, the Status LED will blink to indicate the result of the test.
« 10M Link/A CT LED (yellow) The 10M Link/ACT LED shows the status of the Print Server's 10Mbps network connection © 1. If you are using a basset connection to the Print Serve. the 10M Link/ACT LED wiki normally be an to indicate a good link. 2. The 10M Link/ACT LED will flash when there is network traffic flows on the network. Connecting to the Printer The rear end of the PS-3100+ has three standard 25-pom parallel printer connectors. To connect the Print Server to your printer(s) © 1.
® Features & Specifications Features + One 10BaseT/100Base TX. auto-sensing port. = Three parallel ports, + Windows 95/98 only network printer share support + Quick and easy insulation, support CPD server and client. + Web-based management enables administrator using web browser ro view and configure the print server © Wall mountable. Specifications + One STP connector « Three 25-pin parallel printer connectors + Support SPF mode + Network data transfer rate : 10/100Mbps auto-sensing + Standards : IEEE 802.
Print Sir Plus PS-1100+ Series 1-Port 10/100Mbps Desktop Print Server User’s Manual BW Hardware Installation BR Features and Specifications
= FCC COMPLIANCE STATEMENT This equipment generates and uses radio frequency energy and if not installed and used properly, mat is. in strict accordance with the instructions provided with the equipment. may cause interference to radio and reception, The equipment has been tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Subpart B of Part 13 of FCC rules.
® Hardware Installation Thanks for purchasing this Fast Ethernet Print Server PS-1100= This guide explains its external features, explains how to unpack your Print Server hardware. and tells how you can connect it © our printer and @ your network, Requirements To use your PS+1100+. you will need « A Printer with parallel interface. « Ethernet network cabling, as well as a free abase-T hub: or Fast Ethernet network cabling, as well as a free base's-TX hub.
is LED Indicators The PS-1100+ is equipped with three LED indicators that show its current status, and can be used for diagnosing problems on the network and the Print Server self © 10/100Mbps 1-port Print Server 100MopSLNKIACT ® OMbpailNKACT . Varmint Por « Status LED (green) The Stars LED is iit: |. When the Print Server is powered on. When power is applied to the Print Server. it performs a Power-On Self Test (POST).
+ tOM Link/ACT LED (yellow) The 10M Link/ACT LED shows the status of the Print Server's 10Mbps network connection 1. 1f you are using a basset connection to the Print Server. the 10M Link/ACT LED will normally be on 10 indicate a good link. 2. The 10M Link/ACT LED will flash when there is network traffic flaws on the network. Connecting to the Printer The rear end of the PS-1100= has one standard 25-pin parallel printer connector. To connect the Print Server to your printer 1.
LH. M Features & Specifications Features + One 0BaseT/100BaseTX. aw-sensing port. + One parallel ports. « Windows 93/98 only network printer share support. » Quick and easy installation. support CPD server and client. + Web-based management enables administrator use web browser 10 view and configure the print server. + Wall mountable. Specifications * One STP connector « One 25-pin parallel printer connectors * Support SPP mode + Network data transfer rate © 10/100Mbps auto-easing * Standards : IEEE 802.