Walker W830BT Bluetooth stereo headphones Operating instructions
■ Product introduction Before using this device, please read this manual carefully and keep it safe for future reference. Features ● 40mm Nd-Fe-B unit with high quality sound in strong low frequency; ● Long battery life design to save worry. It works for about 15 hours and standby xx hours; ● Folding portable over-ear, comfortable for wearing and easy for tidying; ● Soft opaline leather ear cover, sound-proof and reducing noise and enjoying tranquility; ● Standard accessory of high-end storage bag, 3.
■ Package list Headphones*1 pcs Storage bag*1 PCS Manual*Warranty card 1 PCS each USB charging cable*1 pcs 3.5mm audio wire*1 PCS ■ Operation instructions 1. Illustration 1.1 Press volume up/Press and hold last song 1.2. Multi-function key 1.3 Press volume down/Press and hold next song 1.4 Micro USB charging port 1.5 3.
2. Charging The headphones use the built-in rechargeable batteries. The batteries must be fully charged before use the headphones. In use, one beep sound every minute and the red light quickly flashing three times indicate that the battery life is low and you need to charge the headphones. 2.1 Plug USB charging wire into USB jacket of standard power. 2.2 Connect the charging wire to Micro USB charging port of the headphones. 2.3 In charging, the headphones’ Bluetooth works normally. 2.
2. Connection 2.1. Bluetooth connection Please complete the connection with your mobile before use. The steps are as below: 2.1.1. The distance between your mobile and the headphones should be kept within 1 m. The closer the better. 2.1.2. The headphones are powered on. Pressing multi-pad 3 seconds makes the headphones into pairing status. 2.1.3. Enable your mobile’s Bluetooth and search Bluetooth devices. Select ‘EDIFIER W830BT’ to pair up and connect.
steps are as below: 2.3.1. Firstly the headphones connecte the device one. 2.3.2. Switch off the headphones and then press and hold multi-pad 3 seconds to restart the headphones and enter the pairing status to connect the device two. 2.3.3. Now operate on the device one. Click the headphones among the Bluetooth connection settings to complete the headphones in connection with two devices; Note: When two connected mobiles have different operating system (E.g. One has Android and one iOS).
call 2 seconds Cancel call Talking Press the multi-function key Increase volume Talking Press the volume + key Decrease volume Talking Press the volume - key Talking transferred Talking Press and hold multi-pad about to mobile 2 seconds Talking transferred Talking Press and hold multi-pad about to headphones 2 seconds Microphone muted Talking Press and hold the volume key about 2 seconds Cancel mute Talking(Microphone muted) Press and hold the volume + key about 2 seconds Redial last
mobile’s incoming call incoming call Switch calls Talking, a call is remained Hang out the current call, Get back to the remained Talking, a call is remained mobile Double click multi-function key Press the multi-function key one time 4. Play music 4.1.
connection automatically disconnected. AUX in audio input is validated. ● If using Bluetooth, please unplug 3.5 audio wire and restart and power on to pair up the connection. 5. Restore factory settings Ensure the headphone is power off and meanwhile press and hold Volume + key and multi-pad about 3 seconds. Then the blue light shall flash quickly 6 times. Now the factory settings are restored. Note: ● After the factory settings are restored, the pair-up list of the headphones shall be cleared.
circuit. ● Do not place the product at the places exposed to sun or in high temperature. High temperature would shorten the service life of electronic components, damage battery and make some plastic components deformed. ● Do not place the product at very cold places to prevent damaging the internal circuit board. ● Do not try to dismantle the product. If non-professional personnel operates, they may damage the product.
b. When the headphones are not used for a long time, the battery will enter the hibernate status. Now it needs to charge about 30 minutes and then the red light shall be on. 3. The headphones hear nothing. Answer: a. Ensure if the headphones are in work status. b. Ensure the headphones volume is suitable. c. Ensure if the headphones are connected with mobile properly. d. Ensure the headphones are in normal work environment. 4. Headphone is not good for talking. Answer: a.
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. A warning that batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. Correct Disposal of this product.
sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. To prevent possible hearing damage, do not listen at high volume levels for long periods. Fully understand user manual before use. Ensure your player at low volume levels or power off before you leaving.
Scan by WeChat for more information Product of Beijing Edifier Technology Co., Ltd Address: No. 68, the West Road of the 4th Northern Ring, Haidian District, Beijing Manufacturer: Dongguan Edifier Technology Co., Ltd Address: No. 2, Gongye Dong Lu, Dongguan Songshan Lake Hi-tech Industrial Development Zone Trademark: EDIFIER○R , Walker○R both are the registered trademark of Beijing Edifier Technology Co., Ltd. Counterfeiting is not allowed. Version No. Ver1.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1)this device may not cause interference, and (2) this device must accept any interference, includinginterference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts de licence.