Managed Gigabit Switch with SFP+ Model: ES-48-Lite
Introduction Thank you for purchasing the Ubiquiti Networks® EdgeSwitch® Lite. This Quick Start Guide is designed to guide you through installation and also includes warranty terms. Package Contents EdgeSwitch Lite Power Cord Rack-Mount Brackets (Qty. 2) Mounting Screws (Qty. 4) Bracket Screws (Qty. 8) Cage Nuts (Qty. 4) TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above).
Installation Requirements • Phillips screwdriver (for rack- or wall-mounting) • Standard-sized, 19" wide rack with a minimum of 1U height available (for rack-mounting) • For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use. • For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply.
Hardware Overview Front Panel LEDs System System LED Note: The System LED functionality has been updated with firmware v1.8.0. We recommend that you update the EdgeSwitch to the latest firmware. State Status Flashing White Bootup in progress. White Ready for use, not connected to Ubiquiti® Network Management System (UNMS™). Blue Ready for use, connected to UNMS. Steady Blue with Occasional Flashing Ready for use, unable to connect to UNMS, check connection to UNMS server.
RJ45: Speed/Link/Act SFP+: Speed/Link/Act SFP: Speed/Link/Act RJ45 LEDs LED Speed/ Link/ Activity State Status Off No Link Amber Link Established at 10/100 Mbps Amber Flashing Link Activity at 10/100 Mbps Green Link Established at 1000 Mbps (1 Gbps) Green Flashing Link Activity at 1000 Mbps (1 Gbps) State Status Off No Link Green Link Established at 1 Gbps Green Flashing Link Activity at 1 Gbps White Link Established at 10 Gbps White Flashing Link Activity at 10 Gbps State Stat
Front Panel Button Reset Button Description There are two methods to reset the EdgeSwitch Lite to factory defaults: Runtime Reset (Recommended) Reset The EdgeSwitch Lite should be running after bootup is complete, and the System LED is white. Press and hold the Reset button. The EdgeSwitch Lite will reboot, and the System LED becomes blue after three seconds. Continue to hold the Reset button for about 15 seconds until the System LED flashes blue for two seconds.
Front Panel Ports RJ45 1-48 SFP+ 1-2 SFP 1-2 Port Description RJ45 1-48 RJ45 ports support 10/100/1000 Ethernet connections. SFP+ 1-2 Hot-swappable SFP+ ports support 1/10 Gbps connections. SFP 1-2 Hot-swappable SFP ports support 1 Gbps connections. Back Panel Console Port Console Port Console Description RJ45 serial console port for Command Line Interface (CLI) management.
Back Panel Power DC Input Power DC Input The 25VDC input can connect a redundant or stand‑alone DC power source (not included) with minimum power: 56W, 25 to 16V, and 2.5 mm DC power inline connector. Note: You can use the redundant DC power source as a hot spare; if the internal AC/DC power supply no longer provides power, then the EdgeSwitch Lite will switch to the DC power source without interrupting its operation. Power Connect the included Power Cord to the Power port.
Mounting in a Rack (Optional) 1. Attach the Rack-Mount Brackets to the EdgeSwitch Lite using the eight Bracket Screws. 2. Attach the EdgeSwitch Lite to the rack using the four Mounting Screws. (If the rack has square slots, then use the Cage Nuts with the Mounting Screws.
Connecting Power 1. Connect the Power Cord to the Power port of the EdgeSwitch Lite. 2. Connect the other end of the Power Cord to a power outlet.
Connecting Ethernet 1. Connect an Ethernet cable from your computer or host system to any port of the EdgeSwitch Lite. 2. Connect Ethernet cables from the Ethernet ports of your devices to the numbered ports of the EdgeSwitch Lite.
Using SFP Ports The specified module types are supported at these speeds: Ports SFP+ Module Type SFP Module Type SFP+ 1-2 10 Gbps 1 Gbps SFP 1-2 (Not supported) 1 Gbps To use an SFP+ or SFP port: 1. Remove the protective plug covering the SFP+ or SFP port. 2. Plug a compatible fiber module into the SFP+ or SFP port. D D M K 0 m 2 n CS 0 1 /M 3 1 S xR s /m pb n M 0 0 5 0 5 0 1 1 xT M 3. Connect the appropriate SFP+ or SFP fiber optic cable to the fiber module.
Accessing the Configuration Interface The EdgeSwitch Lite is set to DHCP by default, so it will try to automatically obtain an IP address. If that fails, then it will use the default fallback IP address, 192.168.1.2. Proceed to the appropriate section, DHCP or Fallback IP Address: DHCP Use one of the following methods: • Set up the DHCP server to provide a specific IP address to the EdgeSwitch Lite based on its MAC address (on the label).
3. The EdgeSwitch Lite Configuration Interface will appear. Customize additional settings as needed. For more information, refer to the EdgeSwitch Lite documentation, which is available at www.ubnt.com/download/edgemax You can also manage your device using UNMS, which lets you configure, monitor, upgrade, and back up your devices using a single application. Get started at www.unms.com Fallback IP Address 1. Ensure that your computer (or other host system) is connected to the EdgeSwitch Lite. 2.
4. The login screen will appear. Enter ubnt in the Username and Password fields. Click Sign In. 5. The EdgeSwitch Lite Configuration Interface will appear. Click the Settings icon.
6. Change the IP Address to a unique IP address. Click Apply. Note: If you change the IP settings, then the session will be cut off, and you will need to reconnect to the EdgeSwitch Lite using the new IP address. Customize additional settings as needed. For more information, refer to the EdgeSwitch Lite documentation, which is available at www.ubnt.
Specifications ES-48-Lite Dimensions Weight Rack-Mount Brackets Included Rack-Mount Brackets Excluded Total Non-Blocking Line Rate Max. AC Power Consumption Power Method AC DC Power Supply Rack-Mount 443 x 43 x 286 mm (17.44 x 1.69 x 11.26") 3.65 kg (8.05 lb) 3.56 kg (7.85 lb) 70 Gbps 56W 100-240VAC/50-60 Hz, Universal Input DC 56W, 25 to 16V, with 2.5 mm DC Power Inline Connector AC/DC, Internal, 56W DC Yes, 1U High ESD/EMP Protection Air: ± 24 kV, Contact: ± 24 kV Shock and Vibration ETSI300-019-1.
Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Failure to provide proper ventilation may cause fire hazard. Keep at least 20 mm of clearance next to the ventilation holes for adequate airflow. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. WARNING: Do not use this product in location that can be submerged by water.
Limited Warranty www.ubnt.com/support/warranty/ The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
Declaration of Conformity български [Bulgarian] С настоящото UBIQUITI NETWORKS декларира, че това устройство ES-48-Lite е в съответствие със съществените изисквания и други приложими разпоредби на Директиви 2014/30/ЕС, 2014/35/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: www.ubnt.
Italiano [Italian] Con la presente, UBIQUITI NETWORKS, dichiara che questo dispositivo ES-48-Lite, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti delle direttive 2014/30/UE, 2014/35/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: www.ubnt.
www.ubnt.com Ubiquiti Networks, Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA ©2015-2018 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, EdgeMAX, EdgeOS, EdgeSwitch, TOUGHCable, and UNMS are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are the property of their respective owners.
