Handbook ECWO5213-L Access Point
Handbook ECWO5213-L Access Point ENGLISH Copyright Notice This document is protected by USA copyright laws and other laws. Besides, the document is the property of Edgecore Networks Corporation. You may not copy, reproduce, distribute, publish, display, perform, or modify any part of this publication in any form or by any means without prior written permission from Edgecore Networks Corporation. You may not alter or remove any copyright or other notice from copies of the content.
Handbook ECWO5213-L Access Point ENGLISH FCC CAUTION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Handbook ECWO5213-L Access Point ENGLISH 5. Warning Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty. The antenna gain, antenna type and output power that can be used for the device and the info listed below are correct and represent the product. Antenna No. 1 2 Frequency (MHz) 2400~2500 2400~2500 2.4GHz antenna spec. Peak Gain (dBi) 10.9 11.
Handbook ECWO5213-L Access Point ENGLISH Model ā ECWO5213-L The device has been tested and passed the requirements of the following standards, and hence fulfills the EMC and safety requirements of RED within the CE marking requirement. ļ Radio: EN 300 328 V2.1.1, EN 301 893 V2.1.1 ļ EMC: EN 301 489-1 V2.1.1, EN 301 489-17 V3.1.
Handbook ECWO5213-L Access Point ENGLISH Preface Package Contents Edgecore ECWO5213-L Outdoor Access Point is an enterprise-grade dual radio 802.11 a/b/g/n + ac Wave 2 Access Point with the best performance for 1. Edgecore ECWO5213-L x 1 2. Handbook x 1 3. Metal Strip x 2 business and industrial applications. Featuring two 2x2 MIMO radios, the ECWO5213-L can simultaneously support up to 300 and 867 Mbps data rates in the 2.4 and 5 GHz bands respectively.
Handbook ECWO5213-L Access Point ENGLISH System Overview ECWO5213-L Side 1 Power LED ECWO5213-L Back ECWO5213-L status. The Power LED will start blinking when the ECWO5213-L is booting. After finishing booting, the Power LED will always on. 2 LAN1 LED Uplink status. The LAN1 LED will light up when there is traffic passing through the LAN1 port. 3 LAN2 LED LAN status. The LAN LED will light up when there is traffic passing through the LAN port. 4 2.4G LED 2.4G Wi-Fi status. The 2.
Handbook ECWO5213-L Access Point ENGLISH 6 LAN1 (PoE) Port Offers uplink connection. This port can be used to connect to a controller, gateway, or directly to the Internet. 802.3at PoE is also supported. 7 Ventilation Valve Due to extreme weather conditions, water vapor in the ECWO5213-L may condense. The valve allows ventilation to prevent moisture buildup within the ECWO5213-L. 8 LAN2 Port The ports for connections with LAN side devices. 9 Wall Mounting Holes For hanging ECWO5213-L.
Handbook ECWO5213-L Access Point ENGLISH Hardware Installation Please follow the steps mentioned below to install the hardware of ECWO5213-L: 1. Place the ECWO5213-L at the best location. The best location for ECWO5213-L is usually at the center of your intended wireless network. Wall mount 1. Secure screws on the wall. 2. Hang ECWO5213-L on the wall by pole mounting holes.
Handbook ECWO5213-L Access Point ENGLISH Pole mount 1. Insert the metal strips through the pole mounting gap. 2. Join the two ends of the metal strips and adjust the length for tight fitting around the pole. 2. Connect the ECWO5213-L to your network device. Connect one end of the Ethernet cable to the LAN1 (PoE) port of ECWO5213-L and the other end of the cable to a switch, a router, or a hub. ECWO5213-L is then connected to your existing wired LAN network. 3. Power on the ECWO5213-L.
Handbook ECWO5213-L Access Point ENGLISH Getting Started Edgecore ECWO5213-L supports web-based configuration. Upon the completion of hardware installation, Access Point can be configured through a PC by using its web browser such as Mozilla Firefox 2.0 or Internet Explorer version 6.0 and above. The default values of LAN IP address and subnet mask of ECWO5213-L are: IP Address 192.168.1.10 Subnet Mask 255.255.255.0 Steps: 1.
Handbook ECWO5213-L Access Point ENGLISH 4. After a successful login into ECWO5213-Lās Web user interface (Web UI), a System Overview page of web management interface will appear, as depicted below. The Web Management Interface - System Overview Page Congratulations! Now, Edgecore ECWO5213-L is installed and configured successfully.