OAP100 Access Point
Quick Installation Guide OAP100 Access Point ENGLISH Copyright Notice This document is protected by USA copyright laws and other laws. Besides, the document is the property of Edgecore Networks Corporation. You may not copy, reproduce, distribute, publish, display, perform, or modify any part of this publication in any form or by any means without prior written permission from Edgecore Networks Corporation. You may not alter or remove any copyright or other notice from copies of the content.
Quick Installation Guide OAP100 Access Point ENGLISH FCC CAUTION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Quick Installation Guide OAP100 Access Point ENGLISH Professional installation instruction 1. Installation personal This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. Professional installation is required. 2.
Quick Installation Guide OAP100 Access Point ENGLISH Radio - EN 300 328 V2.1.1 (2.4G/BT-LE) - EN 301 893 V2.1.1 (5G) - EN 301 908-1 V11.1.1 (LTE) - EN 303 413 V1.1.1 (GPS) - EN 50385 / EN 62311: 2017 (MPE) EMC - EN 301 489-1 V2.1.1 - EN 301 489-17 V3.1.1 - EN 301 489-52 V1.1.
Quick Installation Guide OAP100 Access Point ENGLISH Preface Package Contents Edgecore OAP100 Outdoor Access Point is an enterprise-grade dual radio 802.11 a/b/g/n + ac Wave 2 Access Point with the best performance for business and industrial applications. Featuring two 2x2 MIMO radios, the OAP100 can simultaneously support up to 300 and 867 Mbps data rates in the 2.4 GHz and 5 GHz bands respectively. 1. Edgecore OAP100 x 1 2. Quick Installation Guide (QIG) x 1 3. Terminal Plug 4.
Quick Installation Guide OAP100 Access Point ENGLISH System Overview OAP100 Front OAP100 Back 1 LTE Module Case For inserting LTE Module. 2 Reset Press once to restart the system; to reset the system to factory default settings, hold for more than 5 seconds (the System LED will blink fast).
Quick Installation Guide OAP100 Access Point ENGLISH OAP100 Side 3 Power LED The Power LED will always on when OAP100 power up. 4 System LED The System LED will always on when OAP100 power up. When OAP100 is booting or rebooting, the System LED will blink. 5 Uplink LED There is uplink traffic, the Uplink LED will blink. The orange LED will light up when the link speed is 1Gbps. The green LED will light up when the link speed is 10/100Mbps. 6 LAN LED There is LAN traffic, the LAN LED will blink.
Quick Installation Guide OAP100 Access Point ENGLISH 4
Quick Installation Guide OAP100 Access Point ENGLISH 11 LTE Antenna Connector For attaching LTE Antenna. 12 Ground Connector For connecting the ground wire. 13 Console Port Offering console connection for advance setting. 14 LAN (PoE Out) Port The ports for connections with LAN side devices. 15 Uplink (PoE In) Port Offering uplink connection. This port can be used to connect to a controller, gateway, or directly to the Internet. 802.3at PoE is also supported.
Quick Installation Guide OAP100 Access Point ENGLISH Hardware Installation Please follow the steps mentioned below to install the hardware of OAP100: 1. Place the OAP100 at the best location. The best location for OAP100 is usually at the center of your intended wireless network.
Quick Installation Guide OAP100 Access Point ENGLISH Pole mount with bracket-1 and bracket-2 (optional) Pole mount with bracket-1 and bracket-3 (optional) 7
Quick Installation Guide OAP100 Access Point ENGLISH 2. Connect the OAP100 to your network device. Connect one end of the Ethernet cable to the LAN1 (PoE) port of OAP100 and the other end of the cable to a switch, a router, or a hub. OAP100 is then connected to your existing wired LAN network. 3. Power on the OAP100. OAP100 Uplink (PoE In) port is capable of receiving DC currents. Connect an IEEE 802.3at-compliant PSE device (e.g.
Quick Installation Guide OAP100 Access Point ENGLISH Getting Started Edgecore OAP100 supports web-based configuration. Upon the completion of hardware installation, Access Point can be configured through a PC by using its web browser such as Mozilla Firefox 2.0 or Internet Explorer version 6.0 and above. The default values of LAN IP address and subnet mask of OAP100 are: IP Address 192.168.1.10 Subnet Mask 255.255.255.0 Steps: 1.
Quick Installation Guide OAP100 Access Point ENGLISH Administrator Login Page 4. After a successful login into OAP100’s Web user interface (Web UI), a System Overview page of web management interface will appear, as depicted below. The Web Management Interface - System Overview Page Congratulations! Now, Edgecore OAP100 is installed and configured successfully.
