User's Manual

ManualsBrandsEdgecore Networks ManualsElectronics802.11ac Cloud-based Indoor Dual Band Enterprise Acess Point

– 1 –

Quick Start Guide

802.11ac Cloud-based Indoor Dual Band Enterprise Acess Point

ECW7211-L

The ECW7211-L AP includes its own built-in features for mounting the unit to a wall

or suspended ceiling T-rail.

Note:

For Safety and Regulatory information, refer to the Safety and Regulatory

Information document included with the AP.

Caution:

The planning and installation of the AP requires professional personnel

that are trained in the installation of radio transmitting equipment. The user is

responsible for compliance with local regulations concerning items such as

antenna power, use of lightning arrestors, grounding, and radio mast or tower

construction. Therefore, it is recommended to consult a professional contractor

knowledgeable in local radio regulations prior to equipment installation.

Follow these steps to install the AP:

1. Unpack the AP Unpack the AP and check the package contents.

◆ 802.11a/ac/b/g/n Wireless Access Point

◆ AC power adapter

◆ Console cable

◆ Ceiling-mount accessory

◆ Four adhesive foot pads

◆ Documentation — Quick Start Guide (this guide) and Regulatory and Safety

Information

E012015-AP-R01

150200001031A

www.edge-core.com

Summary of content (5 pages)

PAGE 1
Quick Star t Guide 802.11ac Cloud-based Indoor Dual Band Enterprise Acess Point ECW7211-L The ECW7211-L AP includes its own built-in features for mounting the unit to a wall or suspended ceiling T-rail. Note: For Safety and Regulatory information, refer to the Safety and Regulatory Information document included with the AP. Caution: The planning and installation of the AP requires professional personnel that are trained in the installation of radio transmitting equipment.
PAGE 2
Quick Start Guide 2. Mount the AP After planning your installation, mount the unit on a wall or suspended ceiling T-rail. 2 1 Mounting on a Wall 1 Set two screws in the wall 116 mm (4.57 in.) apart. 2 Slide the AP’s wall mounting slots down onto the screws so that the unit is secure. 1 2 3 Mounting on a Ceiling T-rail 1 Position the ceiling-mount accessory clip holders on either side of the T-rail. 2 Turn the ceiling-mount accessory until the two clips lock it to the T-rail.
PAGE 3
Quick Start Guide 3. Connect Cables Connect network cable to the Eth0/PoE 1000BASE-T RJ-45 port for your network connection. The Etho/PoE port connection can also provide PoE power to the unit. (Optional) Connect a local LAN switch or computers to the LAN1 and LAN2 100BASE-TX RJ-45 ports. 1 1 Connect Category 5e or better cable to the Eth0/PoE RJ-45 port. 4. Connect Power If you do not power the unit using PoE, connect the AC power adapter to the AP and to an AC power source.
PAGE 4
Quick Start Guide 5. Verify AP Operation Verify basic AP operation by checking the system LEDs. The WAN LED and any connected LAN port LEDs should light up green. The circular LED on the top panel should light up green and blue to indicate 2.4 GHz and 5 GHz radio operation respectively. 1 2 3 4 1 Power 3 Eth1 2 Eth0/PoE 4 Radio — LED2.4 G / 5 GHz 6. Connect to the Web The AP offers a user-friendly web-based management interface for the User Interface configuration of all the unit’s features.
PAGE 5
Quick Start Guide Hardware Specifications Item Specification Chassis Size (W x D x H) 200 x 200 x 36.5 mm (7.87 x 7.87 x 1.44 inch) Weight 750 g (1.65 lb) Temperature Operating: 0 °C to 45 °C (32 °F to 113 °F) Storage: -40 °C to 70 °C (-40 °F to 158 °F) Humidity Operating: 5% to 95% (non-condensing) Network Interfaces Ports Eth0/PoE RJ-45 Port: 1000BASE-T, PoE+ PD Eth1 RJ-45 Ports: 1000BASE-TX 2.4 GHz Radio IEEE 802.11b/g/n 5 GHz Radio IEEE 802.