深圳市创荣发电子有限公司 SHENZHEN C&D ELECTRONICS CO., LTD. 红外+蓝牙遥控器产品规格书 IR + BT Remote Control Product Specification 文件编号：Document No.
、目录 Index NO.
、 检验内容及要求 (Verification content & Requirement) 3.1 一般项目 General items A.适用范围: RC25F 遥控器 B.工作环境 0℃~40℃、45﹪~90﹪RH、86~106Kpa C.存储温度-25℃~60℃ D.试验环境 5℃~35℃、45﹪~75﹪RH、86~106Kpa E.额定电压 DC3.0V F.适用电池 AAA/UM-4/LR03*2 节 G.尺寸：159.55*40.1*13.99mm A. Scope of application: RF422a remote control B. Working environment: 0 ℃ ~ 40 ℃, 45% ~ 90% RH, 86 ~ 106kpa C. Storage temperature - 25 ℃ ~ 60 ℃ D. Test environment: 5 ℃ ~ 35 ℃, 45% ~ 75% RH, 86 ~ 106kpa E. Rated voltage DC3.0V F.
3.3 电气性能 Electrical performance No 测试项目 Test items 测试要求 Test requirements 1 工作频率 working frequency 2.402~2.480GHz±50KHz 2 工作电压 working voltage DC2.2V~3.6V 3 休眠电流 Sleep current ≤ 5 uA 4 工作电流 Working current ≤ 30 mA 5 6 BT 通信距离 可达 10 米 BT Communication distance Up to 10 meters IR 发射角度和距离 有效操作距离必须在 8M 以上，有效操作角度要求为接收器中心线上、下、 （工作电压 3.0V) 左、右≥15 度±5 度，直线有效操作距离必须在 12M 以上 3.
水平和垂直方向，每个方向两种频率各 5 个循环：a、频率 10~30~10Hz 位移距离 0.75mm b、频率 30~55~30Hz 位移距离 0.15mm，测试后检测 结构无损伤, 电气性能正常 7 振动测试 Vibration test In horizontal and vertical directions, there are 5 cycles for each frequency in each direction: A. displacement distance of frequency 10-30-10hz is 0.75mm B. displacement distance of frequency 30-55-30hz is 0.15mm. After the test, the structure is free of damage and the electrical performance is normal 1. 3M 胶纸（600）5 次无脱落现象 喷油丝印附着力测试 8 2. RCA 测试:以 225gf 力测试纸带长度 100CM 无脱落现象.
4、主要功能 Main functions 4.1 配对: Pairing method: A、 长按“Power”+“OK”键 3s 后遥控器进入广播模式。 B、 遥控器进入广播模式 1 分钟后还未进入配对模式，超时退出广播。 C、 配对成功，绿灯常亮 3s，失败绿灯直接熄灭，回连时绿灯闪烁，直至回连成功，最长 5s。 D、 清除配对：长按“Power”+“Mute”按键 3s，清除配对信息。 A. Press“Power”and “OK” key for 3 seconds and the remote will enter broadcast mode. B. If the remote control is in the pairing mode after entering the broadcast mode within 1 minute, it will exit broadcast mode. C.
C. Low voltage prompt: low power alarm in connection state, if voltage is lower than 2.2V, press any key led, LED flash 6 times, No more prompts within 10s. D、截止状态提示：电压低于 2.0V, 暂停红外、蓝牙功能，按任意键红、绿 LED 交替快闪 6 次 10s 内不再 提示; D. Cut-off status prompt: when the voltage is lower than 2.0V, pause the infrared and Bluetooth functions, and press any key to alternately flash red and green LED for 6 times, No more prompts within 10s. 4.
POWER 键将同时传输 BT 和 IR。 POWER key will transmit BT and IR simultaneously. 4.8 IR Function： HOW TO SET UP THE RCU By entering Device Code You may setup the URC by following the code entering instructions. Referring to the DEVICE CODE LIST, look up the 3-digit Device Code which corresponds to the brand of your TV. If there is more than one Device Code listed under your brand, start from the first code. Hold down “ POWER ” and “ VOL+ ” on the URC simultaneously for 2 seconds until the indicator lights up.
Hold down “ POWER ” and “ VOL+ ” on the URC simultaneously for 2 seconds until the indicator lights up Enter ‘9’, ‘9’, ‘9’, 3-digital to Reset to Factory Settings, the Red + Green LED indicator will turn on 1.5s then off after completed the process. TV default code: 011 (Sony); BLE will be unpaired.
5、产品效果图 (Product Cosmetics drawing) 10
7、爆炸图 (Explosion drawing) 13
8、产品尺寸图 (Dimension drawing) 14
9．包装尺寸图 (Packagingdrawing)(参照 RC25F) 15
