EcoTrek Waterproof Outdoor Speaker 1 User Guide 2
IMPORTANT SAFETY INFORMATION WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) AS THERE ARE NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of non-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
EcoTrek Layout Models: GDI-EXTRK200...
Connect + Power In/Out Connections Do NOT use these connections if they are wet. USB Jack Microphone Jack AUX Jack Microphone Input: You can input a microphone, guitar, or other musical instrument. Port is ¼" (6.35 mm). Auxiliary Input: This input can be used to connect a CD player, MP3 player, etc. USB Charging Port: Connect your device’s charge cable here to charge it. USB charging only functions when the EcoTrek’s power is turned on. USB port rating is 5V, 2.1A.
Important: Maintaining Waterproofness If the caps on the left side panel are not properly closed, the unit is NOT watertight. Waterproof Caps To close properly, turn the cap clockwise so the cap’s arrow point lines up with the locked symbol . To access the connections, turn the cap counterclockwise so the cap’s arrow point lines up with the unlocked symbol , then pull the tab on the cap to open.
Display + Controls Cup Holders 8. Master Volume Control: Press to adjust the speaker’s main mix volume. Press and hold to adjust the volume continually (volume levels are 0 to 30). 9. Backlight Button: Press to turn button backlights on / off. 10. Tune Buttons: Press these buttons to tune in a radio station. To “seek” (jump to the next available station), press and hold either button down for a few seconds until it starts to seek a station. 11.
Operations Adjust the Master Volume LD AN D S P 1. Press RES HO briefly to adjust the speaker volume. 2. Press and hold to adjust the speaker volume continuously (volume levels are 0 to 30). a. Press briefly to increase one volume level. Press and hold to keep increasing the volume until maximum volume level is reached. b. Press briefly to decrease one volume level. Press and hold to keep decreasing the volume until minimum volume level is reached.
Play Music (Bluetooth Mode) EcoTalk After the EcoTrek is connected to your Bluetooth device, press briefly on the EcoTrek to play, press again to pause. Press the EcoTalk button to activate the voice assistant on your device (Siri, OK Google, etc.). Once activated, the speakerphone mic on your EcoTrek will hear your voice commands and transfer them to the voice assistant on your device. Press briefly to play previous song. Press next song. Press briefly to get the to adjust the volume.
Equalization Press the EQ button once to activate the Preset EQ modes. Use the Tune buttons to cycle through the five modes: Normal, Jazz, Rock, Classical, and Pop. EcoConnect - Wireless Stereo Connection of Two Speakers After six seconds of inactivity, the EcoTrek will automatically exit the EQ Input screen; the EQ button must be pressed again to change modes. Notes: · The EcoTrek will automatically save your EQ settings even after powering the speaker off.
speaker," respectively. When in mono mode, both speakers will announce, "Mono mode." The EcoConnect connection between the two EcoTrek speakers will NOT automatically re-connect after the speakers are turned off. To re-establish EcoConnect between the speakers, after power off, please follow the above steps. Notes: · You can also pair the EcoTrek with any other ECOXGEAR speaker bearing the EcoConnect symbol .
Specifications FCC STATEMENT: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.) This device may not cause harmful interference, and 2.) This device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
You should always 1.) Use the ECOXGEAR speaker in accordance with any music or noise rules and regulations. 2.) Properly seal the ECOXGEAR prior and after each use when in humid or water environments to avoid water damage to the internal components. Salt water / air is particularly corrosive. Always make sure that the gaskets are sealed when in a salt water environment and that the unit is properly rinsed off after use. 3.