www.ecoxgear.
Quick Start 1 Open Cap on the side of your EcoEdge 2 Turn on the Main Power Switch 3 Press the Standby Button to power on your EcoEdge 4 Search your Bluetooth Connection on your Smart Device 5 Pair & Play POWER + CONNECT only for the original owner who purchases the unit from an authorized dealer. Transfers do not qualify for warranty protection. Grace Digital reserves the right to replace any out-of-stock or discontinued product with a comparable product.
6) AVOID prolonged exposure to ultraviolet radiation (UV sunlight) and strong magnetic fields. 7) Periodically check the rubber seal for premature wear. 8) Periodically clean the rubber with a soft moist cloth and ensure no objects such as dirt, hair, or sand are on the rubber seal ring. Do NOT use any oily solvent or chemicals for cleaning. 9) Rinse off the unit with tap water after use in salt water or swimming pool.
Control Buttons & Operations On/Off Press the Standby Power Button once to power On/Off. IMPORTANT: Standby Power function will NOT operate when the Master Power is set OFF. Master Power Switch under the cap on the side panel must be set ON for Standby & your EcoEdge to operate. Bluetooth Once turned on, the EcoEdge will search for your Bluetooth. Refer to Set Up Recommendations 1-2-3 part 3 for details. EcoConnect Functionality is only available between two units.
You should always 1) Use the ECOXGEAR speaker in accordance with any music or noise rules and regulations. 2) Use the proper ECOXGEAR mounts if you intend to mount the unit. 3) Properly seal the ECOXGEAR prior and after each use when in humid or water environments to avoid water damage to the internal components. Salt water / air is particularly corrosive. Always make sure that the gaskets are sealed when in salt water environment and the unit properly rinsed off after use.
EcoTalk Press the EcoTalk button to activate the voice assistant on your device (Siri, OK Google, etc.). Once activated, the speakerphone mic on your EcoEdge will hear your voice commands and transfer them to the voice assistant on your device. NOTE: Before using the EcoTalk function, your device must be connected to the EcoEdge via Bluetooth. Not all devices have voice assistant functionality; refer to your device for details. ATTENTION: Do NOT dispose of in a landfill. Contact Grace Digital at www.
water, clean it thoroughly after use with fresh water. The USB cables and unit with an improperly fitted cap are NOT waterproof. To prevent fire or shock, do NOT attempt to charge this unit if it is wet or you suspect water has entered the unit. In this situation, please return the unit to Grace Digital for a free assessment. If we have found that the unit has carried water, we will repair or replace the unit free of charge. SAFETY ADVISORY & WARNING: Read and follow all instructions. Use only as intended.
Set Up Recommendations 1-2-3 1 Charge Your EcoEdge Before you power on your EcoEdge, connect the USB Micro port to the USB cable and a 5V power source to fully charge your EcoEdge for best performance. NOTE: Before using your EcoEdge for the first time, charge the unit until all battery level indicators are green, indicating a full charge. Approximately 3 hours of charging is required from a low to a full charge.
FCC STATEMENT: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
3 Bluetooth Pairing & Your Audio Connecting With Bluetooth: Connect To Your Smart Device & Play Audio When your EcoEdge is turned on, the blue LED light on the top panel will flash, indicating the unit is ready to pair. Turn on Bluetooth on your Bluetooth device (Smart Device) and set the device in pairing mode. Available Bluetooth connections shall appear. Select the ECOXGEAR speaker from the list of discovered devices on your Bluetooth device. Wait for a few seconds until the connection is completed.
What’s in the Box EcoEdge Models: GDI-EXEDGE300...320 User Guide EcoEdge Unit User Guide Carabiner USB Cable When the ECOXGEAR selection is made and the Bluetooth connection is completed, your EcoEdge will announce: “Connection successful” Once connected, select and play your desired audio. Pairing Mode: If the LED is not flashing or if you wish to place your EcoEdge in pairing mode, press and release the Bluetooth button on the top panel.
will look to re-establish that connection. If Bluetooth is turned off on your Smart Device, the EcoEdge may not automatically look for the device. RECOMMENDATION: If you are not familiar with Bluetooth pairing for your Smartphone or other Smart Device, refer to the User Guide for your Smartphone to learn how to add and pair a new device (EcoEdge for instance) to your Smartphone using Bluetooth.
Unit Weight 17 ounces Output Power 20W Max Amp, x1 woofer (Ø3”) S/N Ratio 88dB +/- 3dB Power Source 3.6V, 3350mAh Lithium Ion Battery USB Input 5V, 1A Frequency Range 125Hz-18,000Hz Bluetooth Bluetooth® CSR 4.
both of your EcoEdge speakers. Both speakers will announce, “EcoConnect, pairing speakers.” Wait approximately 4 seconds for the speakers to wirelessly connect. Both speakers will announce “Connection successful. Speakers paired.” and the EcoConnect light will turn solid BLUE on both units once the connection is completed. Once the two EcoEdge speakers are connected via EcoConnect, start playing music from your device. Both connected EcoEdge units will play the music from you device.
POWER + CONNECT Important: Maintaining Waterproofness Your EcoEdge is only waterproof when the cap is properly closed. In order to properly close the cap, push firmly to be sure the cap fits flat and flush along the edges with the panel. If not properly closed the unit is NOT watertight and may not float. The EcoConnect connection between the two EcoEdge speakers will NOT automatically re-connect after the speakers are turned off.
Master Power Switch & Connections Master Power Switch EcoEdge has a separate Master Power Switch and a Standby Button. The switch MUST be set to the ON position to power your EcoEdge. Once the switch is set to ON, use the Standby Button located on the top panel to turn the unit On/Off. NOTE: When not in use for extended periods, turn the Master Power off to preserve battery life. IMPORTANT: Standby Power function will NOT operate when the Master Power is set to OFF.
