R
Product Overview Thank you for purchasing the bēm wireless Party Block. Our speaker will bring you a new found freedom from wires while delivering an incredible sound. The Party Block is compatible with all devices enabled with Bluetooth© technology... which is currently a lot of devices! Make sure to read through the following directions, fully charge your device and perform the initial Bluetooth© syncing process and you should be up and running in no time. If you have any problems stop on by bemwireless.
Meet the Party Block Before learning your Party Block, take a moment to look it over and familiarize yourself with its features. Product Interface: The Sender usb charge 5 4 1 2 3 1. 2. 3. 4. 5. 6. 7. 8.
Product Interface: Satellite Speaker 9 1 2 3 4 5 6 7 8 10 11 1. 2. 3. 4. 5. 6. 7. 4 Connection Indicator Power/Pair Light On/Off Light Mode Music Sensor On/Off Volume Volume + 12 8. 9. 10. 11. 12.
Getting Started We know you are excited to experience your new Party Block. These two easy steps will get you up and running quickly. Step 1: Power It •• Connect your Party Block to an outlet using the included 5V,2A power adapter. It will start charging the Sender. The power indicator will slowly flash during charging and goes out when it has reached a complete charge (Approx. 3.5 hours). •• Connect the Satellite Speaker to an outlet using the included 12V,2A power adapter.
Step 2: Connect it (continued) Next time the Party Block and connected device will pair automatically. After completing this step you are ready to start playing audio from your connected device. Holding the Play/Pause button for 5 seconds will disconnect the connected device and enter pairing mode for pairing a new device. Direct Connection The Party Block can also be connected to any device that has a headphone jack or line out using the included aux cable.
Operation Details (cont.) Play modes • Bluetooth mode: plays an audio signal from the connected Bluetooth© device. • AUX mode: plays an audio signal from the connected “wired” device. Please note, the Bluetooth has the priority to play, if an Aux cable is connected to the speaker, please turn off the Bluetooth© music or disconnect Bluetooth device first for playing an audio signal from AUX. Audio Use Follow the above connection steps to pair a Bluetooth© device with the Party Block.
Connection Laptop / notebook / PC As the Bluetooth© versions for these types of devices varies greatly, the connection methods will differ as well. If you can not connect with the Party Block using the previous method instructed you may need to install a new version of the Bluetooth© driver. Please reference the instructions of device for details. Speaker Placement The Sender has built-in battery and is portable. This allows the perfect placement of the sender for maximum distance.
Charging Your Device The sender features a standard USB charging port with 5V,1A output at the back which can charge most cell phone and tablet, Please reference the instructions of device for details. The charging cable is not included. Using the Device Stand Slide the sender open to use the device stand. The back rest was designed to tilt your device at a 25 degree angle for optimal viewing. Adding Additional Speakers You can run up to 99 Party Blocks off of 1 sender.
Troubleshooting Issue: Pairing is unsuccessfully after multiple attempts Solution: •• Check if the Bluetooth© indicator light is on. If the indicator light is off, please press the power button to turn the unit on. If the Bluetooth© indicator light still doesn’t come on after pressing the power button, please charge the unit. •• Check for other Bluetooth© devices around the surroundings that may interfere with searching and turn devices off.
•• Do not set the unit in a damp environment, high temperatures or in direct sunlight. Maintenance Please follow the instructions below for cleaning your Party Block •• Power off the unit and unplug the power adapter from wall outlet •• Use a soft, dry, lint-free cloth and wipe gently •• Do not use alcohol, benzene, thinners or other chemical detergents as these can cause the casing to be warped or discolored For questions, comments or to purchase more bem wireless products go to bemwireless.
FCC Statement (cont.) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Product Name : Party Block Model Number : HL2536 Power Supply: 5V,2A for Sender and 12V,2A for Speaker Output power: 10W X 2 USB charging output: 5V,1A x 1 Battery capacity: 3.7V 2000mAh for the case ,7.4V 4000mAh for the speaker Bluetooth V4.
Safety Instructions This product is specially designed based on the full attention to safety; in order to make sure the accident-free operation, please abide the guidelines listed below: •• Always position the unit on a stable and level surface.
Safety Instructions (cont.) WARNING: •• The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine, fire or the like. •• No naked flame sources, such as lighted candles, should be placed on the apparatus. •• CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. More Info For questions, comments or to purchase more bēm wireless products go to: bemwireless.com You can also follow us at: facebook.
bēm wireless | 1725 Kilkenny Court | Woodstock IL 60098 TEL: 855-839-8616 © 2014 bēm wireless