User's Manual

ManualsBrandsEcolink Intelligent Technology ManualsElectronicsHome Motion Sensor

Motion Sensor with Pet Immunity Installation Instructions

Product Overview

 Z-Wave+

enabled device which transmits upon detection of movement

 Configurable to be less sensitive to the movement of small and medium size household pets

 Reports tamper condition if cover is removed

Product Specifications

 For indoor use only

 Operating frequency: 908.42 MHz

 Operating range: Up to 100 feet (30.5 meters) line-of-sight

 Operating temperature: 0˚C to 49˚C, 32˚F to 120˚F (ambient temperature)

 Detection radius: 39 feet (see detection region diagram)

 Detection angle: 45 degrees in either direction from the sensor’s center (see detection region diagram)

 Battery type: 3V Lithium CR123A

 Battery life: approximately 3 years

 Passive Infrared (PIR) based technology

Network Inclusion

The sensor must be added to a Z-Wave network prior to use. To include the sensor in a network both the sensor and the network

controller must be in inclusion mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller

for details on initiating the controller’s inclusion mode.

STEP ONE Start by placing the controller into inclusion mode.

STEP TWO Activate inclusion mode for the sensor by removing the battery isolation pull tab, or by inserting the battery (see

next section for battery installation tips). When the inclusion process is complete the red LED will turn on for

approximately 10 seconds and then it will go out. If the LED continues to flash repeat the inclusion process.

STEP THREE Test the motion sensor before mounting it. Place the sensor in an unoccupied room. Leave the room for

at least 4 minutes. Return to the room and pass in front of the sensor lens. The LED will flash once to indicate

that motion was detected.

Summary of content (10 pages)

PAGE 1
Motion Sensor with Pet Immunity Installation Instructions Product Overview    Z-Wave+TM enabled device which transmits upon detection of movement Configurable to be less sensitive to the movement of small and medium size household pets Reports tamper condition if cover is removed Product Specifications          For indoor use only Operating frequency: 908.42 MHz Operating range: Up to 100 feet (30.
PAGE 2
Notes:  Sensor inclusion mode can also be initiated by inserting a pin or paper clip into the small round hole on the back side of the sensor.  The sensor also features a test mode so that motion detection can be tested without waiting 4 minutes. For more information refer to the “Test Mode” section of these instructions. Network Inclusion: Key Points to Remember       Controller inclusion mode must be activated BEFORE starting sensor inclusion mode.
PAGE 3
1x 1x 4x 2x 1x 3x Sensor Sensor mounting bracket screws jumper battery pieces of adhesive tape STEP ONE Mount bracket to wall First attach the sensor mounting bracket to the wall using either adhesive tape OR screws (optional). For best performance mount the bracket 6.5 to 7.5 feet above the floor (2 to 2.3 meters). Adhesive Bracket Screws (Optional) Corner Mount Flush Mount Note: For best results, attach adhesive tape to bracket FIRST, then position on wall.
PAGE 4
ADDITIONAL NOTES AND SUMMARY:    BEFORE attaching the bracket to a surface note how the bracket will need to be oriented in order for the tab to engage the sensor. The required orientation of the sensor determines the bracket orientation. The large clip that holds the case together is located on the TOP. Please be advised that adhesive tape may damage the surfaces to which it is attached and then removed from. The sensor slides onto the bracket until the tab engages and CLICKS.
PAGE 5
Test Mode The amount of time it takes for the sensor to reset after motion has been detected can be shortened for quicker motion sensor testing. To enter test mode remove the cover from the sensor. Find the pair of metal pins on the lower right hand side of the circuit board labeled “TEST”. Connect these two pins together using the provided jumper. Replace the sensor cover. After approximately ten seconds the red LED will go out. The sensor is now in test mode.
PAGE 6
Z-Wave Device Class and Command Class Information This Z-Wave sensor is a Z-Wave generic Device Class of GENERIC_TYPE_SENSOR_NOTIFICATION, and a specific device class of SPECIFIC_TYPE_NOTIFICATION_SENSOR, and the supported command classes are COMMAND_CLASS_ZWAVEPLUS_INFO, COMMAND_CLASS_VERSION, COMMAND_CLASS_MANUFACTURER_SPECIFIC, COMMAND_CLASS_POWERLEVEL, COMMAND_CLASS_BATTERY, COMMAND_CLASS_NOTIFICATION_V4, COMMAND_CLASS_ASSOCIATION, COMMAND_CLASS_ASSOCIATION_GRP_INFO, COMMAND_CLASS_WAKE_UP, COMMAND_CLASS
PAGE 7
SENSOR CONDITION COMMAND CLASS and VALUE Notification Report of Home Security (0x07), Motion Detection Unknown Location(0x08) ASSOCIATION GROUP 1 Motion Detected Sensor Binary Report of 0xFF Sensor Type: 0xFF 1 Basic set of 0xFF (On) Notification Report of Home Security (0x07), Event inactive(0x00) 2 1 No More Motion Detected Sensor Binary Report of 0x00 Sensor Type: 0xFF 1 Basic Set of 0x00 (Off) By factory default this feature is disabled and must be enabled via Configuration Command Class.
PAGE 8
Sensor Case Removed Notification Report of Home Security (0x07), Tampering product cover removed (0x03) 1 Sensor Case Fastened Wake-Up Notification 1 Battery Level Dipped Below 2.
PAGE 9
Parameter Number: 2 Size: 1 Configuration Value: 0x00 Parameter Number: 2 Size: 1 Configuration Value: 0xFF (Default) Sensor sends Sensor Binary Reports when sensor is faulted and restored for backwards compatibility in addition to Notification Reports. Sensor will send only Notification Reports and NOT Sensor Binary Reports when the sensor is faulted and restored. FCC Compliance Statement This device complies with part 15 of the FCC Rules.
PAGE 10
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of Ecolink Intelligent Technology Inc. neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product.