Product Specs

ManualsBrandsEcolink Intelligent Technology ManualsSmart HomeZ-Wave Siren

Table Of Contents

Page 1 of 10

Chime+Siren Manual

Product Overview

• Z-Wave+™ enabled device which provides open/closed position status

• Transmits open/closed status of eight wired inputs

• Reports tamper condition when cover is open

Product Specifications

• For indoor use only

• Operating frequency:

908.42, 916 MHz

• Operation range: Up to 100 feet (30.5 meters) line-of-sight

• Operating temperature: 0° – 49°C, 32° – 120°F (ambient temperature)

• Line Powered 120v AC 60Hz US

• 24-hour battery backup.

Adding via SmartStart

To add via SmartStart, you will need the device’s DSK QR-Code which is located on the back

side of the device, on the packaging, and on a leaflet within the packaging. Apply power to the

device by inserting the device into a wall receptacle, and the device will go into SmartStart

inclusion mode. While in this mode, the sensor can be added to a Z-Wave controller that supports SmartStart. Please refer to the inclusion controller’s manual

for activating SmartStart.

Summary of content (10 pages)

PAGE 1
Chime+Siren Manual Product Overview • • • Z-Wave+™ enabled device which provides open/closed position status Transmits open/closed status of eight wired inputs Reports tamper condition when cover is open Product Specifications • • • • • • For indoor use only Operating frequency: 908.42, 916 MHz Operation range: Up to 100 feet (30.5 meters) line-of-sight Operating temperature: 0° – 49°C, 32° – 120°F (ambient temperature) Line Powered 120v AC 60Hz US 24-hour battery backup.
PAGE 2
Adding to a Z-Wave Network (Classic Inclusion Method) Make sure the device has power. Press the Add/Test Button which is the smaller of the two buttons, and the device will enter classic inclusion mode which implements both classic inclusion with a Node Information Frame, and Network Wide Inclusion. During Classic Inclusion mode, the Green LED will blink three times every three seconds. When Classic inclusion times-out, the device will blink red and green.
PAGE 3
Led behavior for Inclusion Blink Pattern Smart Start Started Green LED Three Times Classic Inclusion Started Green LED Three Times every three seconds. Classic Inclusion Timed-Out Green and Red several times. Inclusion Successful (Authenticated S2) Green LED on solid Inclusion Not Successful (Self-Destruct) Red LED on solid Removing a Sensor from a Z-Wave Network To remove the device, place the controller into Remove or “Z-Wave Exclusion” mode.
PAGE 4
Z-Wave Device Class and Command Class Information This Z-Wave sensor is a Z-Wave generic Device Class of GENERIC_TYPE_AV_CONTROL_POINT (0x03), and a specific device class of SPECIFIC_TYPE_SOUND_SWITCH (0x01). Manufacturer Specific Manufacturer ID: MFG_ID_ECOLINK Product Type: 0x0007 Product ID: 0x3975 Factory Default To restore the device back to factory settings and remove it from any Z-Wave network. Remove the device from power-outlet.
PAGE 5
Mapping of the Basic Command Class The Chime+Siren has the Basic Command Class mapped such that a Basic Set of 0x00 is always off. A Basic set of 1 is sound 1; 2 is sound 2, 5 is sound 5, etc. Finally a Basic Set of 0xFF is mapped to the primary sound which is either a siren or chime sound.
PAGE 6
Powerlevel 1 No Yes Security 2 1 Yes Yes 1 2 2 2 2 No Yes Yes Yes No Yes Yes Yes Yes Yes Notification 8 Configuration 4 Sound Switch 1 No No No Yes Yes Yes Supervision Transport Service Version Z-Wave Plus Info Basic No Support Authenticated & Unauthenticated Basic Set of 0 to 255 maps to 0: off, and 1-255 enumerated sounds where 255 is a Siren sound. Any Report sent from the Siren is mapped 0: off and 255: Sound playing.
PAGE 7
Configuration Command Class Parameter Name 1 Swap Siren and Chime Sound mapping. 2 Periodic heartbeats 3 Encapsulate Unsolicited Notifications/Reports in Supervision 4 Sound Volume 5 Total Number of Sounds Available Description 0: A Basic Set of 0xFF starts playing Siren. 1: A Basic Set of 0xFF starts playing Chime. The number of seconds between automatic Heartbeat Notifications. Encapsulate Unsolicited Notifications in Supervision Get requests.
PAGE 8
System (0x09) Backup battery level status 0x10 Back-up battery is low System Software Failure (Manufacturer Proprietary Failure Code Provided) 0x04 Heartbeat 0x05 Failure codes-> 0x33 Watchdog Reset on the Z-Wave Module 0x55 Watchdog Reset on the STM32 This is sent out periodically as configured by the Configuration command class. Sounds There are 14 included sounds within the Chime+Siren, and the device can play sounds from the SD card either overriding the build-in sounds or adding to them.
PAGE 9
6 doorbell 7 error 8 Exit_delay DoorBell Sound Action Canceled Sound A loud chirp every second for 30 seconds then every half second forever or another 30 seconds. 9 entry_delay 10 away 11 stay_home A constant tone. Security panel in away mode. Security panel in Stay/home mode where the PIRs are not active. 12 smoke_alarm 13 co_alarm 14 disarmed UL Specified UL Specified Happy sound. Manually Adjusting the Volume The volume buttons on the side of the device can override the volume.
PAGE 10
FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules.