User's Manual

ManualsBrandsEcolink Intelligent Technology ManualsElectronicsDoor & Window Sensor

Door/Window Sensor Installation Instructions

Product Overview

 Z-Wave+™ enabled device which provides open/closed position status

 Transmits open/closed status

 Reports tamper condition when cover is open

Product Specifications

 For indoor use only

 Operating frequency: 908.42 MHz

 Operation range: Up to 100 feet (30.5 meters) line-of-sight

 Operating temperature: 0° – 49°C, 32° – 120°F (ambient temperature)

 Battery type required: 3V Lithium CR123A

 Battery life approximately 3 years

Network Inclusion

The sensor must be added to a Z-Wave network prior to use. To include the

sensor in a network both the sensor and the network controller must be in

inclusion mode at the same time. Refer to the instructions provided by the

manufacturer of your specific controller for details on initiating the controller’s

inclusion mode.

STEP ONE Start by placing the controller into inclusion mode.

STEP TWO Activate inclusion mode for the sensor by removing the plastic pull-tab from the back of the sensor. When the

inclusion process in complete, the LED on the sensor will be solid blue, then go out.

STEP THREE Test the sensor. Place the magnet next to the sensor to represent a closed position (see Installation

section to see where to position the magnet). If the LED flashes ONE TIME, it is successfully communicating on

your Zwave network. If the LED on the sensor flashes slow and steady for 5 seconds, you need to repeat the

inclusion process.

Notes: If you need to repeat the inclusion process, repeat STEP ONE above, then for STEP TWO you will need to simply remove the cover of the sensor, remove the

battery for 10 seconds, reinsert the battery, and replace the sensor cover. This will re-enter the sensor in inclusion mode.

Summary of content (9 pages)

PAGE 1
Door/Window Sensor Installation Instructions Product Overview    Z-Wave+™ enabled device which provides open/closed position status Transmits open/closed status Reports tamper condition when cover is open Product Specifications       For indoor use only Operating frequency: 908.42 MHz Operation range: Up to 100 feet (30.
PAGE 2
Network Inclusion: Key Points to Remember       Controller inclusion mode must be activated BEFORE starting sensor inclusion mode. The sensor can only be included into one controller network at a time, and must be excluded from one network before inclusion in another. Removing the pull tab connects the battery and initiates sensor inclusion mode. Inclusion mode can also be initiated by removing the battery for at least 5 seconds, reinstalling the battery, then replacing the sensor cover.
PAGE 3
Fixed jamb Fixed jamb Door Door Left hand door mounting (arrow pointing UP, magnet on left side) STEP TWO Right hand door mounting (arrow pointing down, magnet on right side) Mount the sensor and magnet to a clean dry surface with the adheasive tape and/or the screws provided Adhesive Tape © 2015 Ecolink Intelligent Technology Inc. Mounting Bracket Screws (optional) Senso r Adhesive Tape Mounting Bracket Screws (optional) Magnet PN DW-ZWAVE2.5 R1.
PAGE 4
IMPORTANT: MAX GAP: 5/8” The edge of the magnet must align with the line on the sensor, AND the magnet must locate next to the arrow on the sensor. Maximum gap between the magnet and the sensor is 5/8”. If the magnet is not located following these rules, the sensor may not get activated. ADDITIONAL NOTES AND SUMMARY:     With either mounting method the first step is to attach the sensor mounting bracket to door frame or window frame.
PAGE 5
What is Z-Wave? The Z-Wave protocol is an interoperable, wireless, RF-based communications technology designed specifically for control, monitoring and status reading applications in residential and light commercial environments. Mature, proven and broadly deployed (with over 35 million products sold worldwide), Z-Wave is by far the world market leader in wireless control, bringing affordable, reliable and easy-to-use 'smart' products to many millions of people in every aspect of daily life.
PAGE 6
Association This sensor has two Association groups of 5 nodes each. Group one is a lifeline group who will receive unsolicited messages relating to door/window open/close notifications, case tampering notifications, low-battery notifications, and sensor binary reports. Group 2 is intended for devices that are to be controlled i.e. turned on or off (on only by default) with a Basic Set. On inclusion the controller should put its node ID in group 1 but not group 2.
PAGE 7
SENSOR COMMAND CLASS and VALUE ASSOCIATION GROUP CONFIGURABLE? CONDITION Notification Report of Access Control (0x06), Door/Window is open (0x16) 1 Door/Window Open Sensor Binary Report of 0xFF Sensor Type: 0xFF 1 Basic set of 0xFF (On) Notification Report of Access Control (0x06), Door/Window is closed (0x17) 2 1 Door/Window Close Sensor Binary Report of 0x00 Sensor Type: 0xFF 1 Basic Set of 0x00 (Off) By factory default this feature is disabled and must be enabled via Configuration Command Cla
PAGE 8
Wake-Up Notification The sensor will wake up every so often and when the case is closed to send a Wake-Up Notification to allow the life line master node controller that the sensor is now available for any queued messages that the controller may have for the sensor. The time between Wake-Up Notifications can be configured with the WakeUp Notification command class to be between 1 hour and 1 week with interval steps of 200 seconds. Configuration The sensor has two configuration parameters.
PAGE 9
FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules.