Installation Instructions

ManualsBrandsEcolink Intelligent Technology ManualsElectronicsWater Sensor

DWWZWAVE2.5-ECO

Z-Wave Plus Water Sensor Installation Instructions

oduct Overview

• Z-Wave+™ enabled device which detects water when used in conjunction with probe

• Transmits open/closed status

• Reports tamper condition when cover is open

oduct Specifications

• For indoor use only

• Operating Frequencies: 908.42 and 916 MHz

• Operation range: Up to 100 feet (30.5 meters) line-of-sight

• Operating temperature: 0° – 49°C, 32° – 120°F (ambient temperature)

• Battery type required: 3V Lithium CR123A

• Battery life approximately 3 years

Network Inclusion

The sensor must be added to a Z-Wave network prior to use. To include the sensor in a network both the sensor and the network controller must be in inclusion

mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating the controller’s inclusion mode.

1) Ver

ify that the Z-Wave Plus controller you are using is compatible with the Water Sensor.

2) Either mount or move the Water Sensor as close as possible to the location the sensor will remain. See installation section below.

3) Put your Z-Wave Plus Controller into add (inclusion) mode.

4) To add the sensor to an existing Z-Wave network, follow the directions to put your Z-Wave Controller into add (inclusion) mode. Activate inclusion

mode for the sensor by removing the plastic pull-tab from the back of the sensor. When the inclusion process in complete, the LED on the sensor will

be solid blue, then go out.

5) Test the sensor. With the flood probe connected, place the probe in a cup of water, or short the contacts of the probe causing the sensor to

represent a closed position. If the LED flashes ONE TIME, it is successfully communicating on your Zwave network. If the LED on the sensor flashes

slow and steady for 5 seconds, you need to repeat the inclusion process.

Net

work Exclusion

1) Any sensor can be removed from any Z-Wave Plus controller. Follow the directions to put your Z-Wave Plus Controller into exclusion mode. Please

use this procedure only when the network primary controller is missing or otherwise inoperable.

2) Open the Water Sensors case and remove the battery for 10 seconds. Replace the battery and the controller should remove the device from the Z-

Wave network.

Summary of content (8 pages)

PAGE 1
DWWZWAVE2.5-ECO Z-Wave Plus Water Sensor Installation Instructions Product Overview • • • Z-Wave+™ enabled device which detects water when used in conjunction with probe Transmits open/closed status Reports tamper condition when cover is open Product Specifications • • • • • • For indoor use only Operating Frequencies: 908.42 and 916 MHz Operation range: Up to 100 feet (30.
PAGE 2
• • • • • Network Inclusion/Exclusion: Key Points to Remember Controller inclusion/exclusion mode must be activated BEFORE starting sensor inclusion or exclusion mode. The sensor can only be included into one controller network at a time, and must be excluded from one network before inclusion in another. The plastic pull tab must be removed to enable sensor operation. The sensor automatically enters inclusion mode at power-up.
PAGE 3
STEP ONE Mount the Sensor: Mount the sensor to a clean dry surface with the bracket, screws, and adhesive tape provided where it will not be immersed or splashed with water. Adhesive Tape STEP TWO Mounting Bracket Screws (optional) Sensor Mount the Probe: Mount the probe to a clean dry surface where water detection is needed. © 2020 Ecolink Intelligent Technology Inc. PN DWWZWAVE2.
PAGE 4
ADDITIONAL NOTES AND SUMMARY: • • • • With either mounting method the first step is to attach the sensor mounting bracket to the mounting surface. (The mounting bracket is used regardless of choice of screws or tape). The sensor can slide onto the mounting bracket in two different ways. To ensure that the sensor is securely fastened it is recommended that the tab on the bracket engage the back of the sensor.
PAGE 5
(Off) Basic Set of 0x00 (Off) By factory default this feature is disabled and must be enabled via Configuration Command Class. Sensor Case Removed Sensor Case Fastened Battery Level Dipped Below 2.
PAGE 6
Product Type: 4 Product ID: 2 Factory Default To restore this sensor to factory default settings, follow the instructions in this manual to exclude this sensor from the Z-Wave network. Upon completion of removal from the network the sensor will restore itself to factory default settings automatically. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.
PAGE 7
redundant, the controller can disable the Sensor Binary Report Commands completely. The following table shows the values to enable and disable the two configuration parameters.
PAGE 8
LIMITED WARRANTY This limited warranty is provided by Ecolink Intelligent Technology (“Ecolink”) to you as the original purchaser of the product. Ecolink warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of original purchase. The determination of whether the product is defective shall be made by Ecolink in its sole discretion with consideration given to the overall performance of the product.