User's Manual

ManualsBrandsEcolink Intelligent Technology ManualsElectronicsDouble Decora Light Switch

Z-Wave Plus Smart Switch – Dual Rocker Installation Instructions

Product Overview

 Z-Wave Plus™ enabled device which can be used turn a light switch on or off

 Z-Wave Plus™ enabled device which can be used sense status of a light switch

Product Specifications

 For indoor use only

 Operating frequency: 908.42 MHz, 916 MHz

 Operating temperature: 0° – 49°C, 32° – 120°F (ambient temperature)

 Operating humidity 5-95% non-condensing

 2 AA batteries

 Battery Life: 1 year

Network Inclusion

The Z-Wave Plus Smart Switch must be added to a Z-Wave Plus network prior to use. To include the device in a network both the device and the network

controller must be in inclusion mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating

the controller’s inclusion mode.

1) Verify that the Z-Wave Plus controller you are using is compatible with the Z-Wave Plus Smart Switch

2) Locate the light switch desired to be used with the Z-Wave Plus Smart Switch.

3) Put your Z-Wave Plus Controller into add (inclusion) mode.

4) Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch. (Figure 1)

5) The LED on the front of the unit will turn off if successful included into a network.

Network Exclusion

1) Any Z-Wave Plus Device can be removed from any Z-Wave Plus controller. Follow the directions to put your Z-Wave Plus Controller into exclusion

mode.

2) Press the inclusion / exclusion button on the Z-Wave Plus Smart Switch.

Network Inclusion/Exclusion: Key Points to Remember

 Controller inclusion mode must be activated BEFORE starting sensor inclusion or exclusion mode.

 The device can only be included into one controller network at a time, and must be excluded from one network before inclusion in another

 Exclusion mode on the senor is initiated following the same exact procedure as inclusion.

DRAFT MANUAL – NOT FOR PRODUCTION USE

Summary of content (6 pages)

PAGE 1
DRAFT MANUAL – NOT FOR PRODUCTION USE Z-Wave Plus Smart Switch – Dual Rocker Installation Instructions Product Overview   Z-Wave Plus™ enabled device which can be used turn a light switch on or off Z-Wave Plus™ enabled device which can be used sense status of a light switch Product Specifications       For indoor use only Operating frequency: 908.
PAGE 2
LED Status The Z-Wave Plus Smart Switch is equipped with a red LED. The state of the LED will change based on the state of the device. LED Blinking LED On LED blink - Device not included into a network. - Device In Learn mode. - Device in lower power mode. Remote control disabled. Battery State The Z-Wave Plus Smart Switch will alert the user when the batteries become low. While the batteries are low, the user will be unable to change the light state remotely.
PAGE 3
STEP ONE Identify Location for Z-Wave Plus Smart Switch: STEP TWO Remove the switch plate cover from the Light Switch you wish to install the device on. Save the screws for step three. STEP THREE Replace the switch plate cover with the Z-Wave Plus Smart Switch using the screws from step two. Select Switch Figure 2 STEP FOUR Follow the Network Inclusiuon steps on page 1. STEP FIVE Move select switch to up position. The UP position is based on how it is mounted.
PAGE 4
Z-Wave Plus Specific Information Z-Wave Plus is a wireless mesh network and data protocol that allows devices from many different manufacturers to interoperate. This device implements ZWave Plus functionality, Network Wide Inclusion, The following information is intended for software engineers working on Z-Wave Plus controllers and home automation enthusiasts to integrate the Z-Wave Plus device into their system.
PAGE 5
Z-Wave Plus Command Class Basic For backwards compatibility with older Z-Wave Plus Controllers, the Basic Command Class is supported in the following manner. A Basic Set of 0xFF will turn on the light switch. A basic set of 0x00 will turn off the light switch. Command Class Association This Z-Wave Plus Smart switch has two Association groups of 5 nodes. Group one – Group one is the lifeline group.
PAGE 6
LIMITED WARRANTY This limited warranty is provided by Ecolink Intelligent Technology (“Ecolink”) to you as the original purchaser of the product. Ecolink warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of original purchase. The determination of whether the product is defective shall be made by Ecolink in its sole discretion with consideration given to the overall performance of the product.