User's Guide

CS-602

AUDIO DETECTOR

patent pending

Installation Manual & Users Guide

SPECIFICATIONS

Frequency: 345MHz

Battery: One 3Vdc lithium CR123A

Battery life: up to 4 years

Detection distance: 6 in max

Operating Temperature: 32°-120°F (0°-49°C)

Operating Humidity: 5-95% RH noncondensing

Compatible with 345MHz ClearSky Hub

Supervisory signal interval: 70 min(approx.)

Maximum current draw: 23mA during transmission

OPERATION

The FireFighter™ sensor is designed to listen to any smoke, carbon or combo detector. Once confirmed as an

alarm, it will transmit a signal to the alarm control panel which if connected to a central monitoring station, will

dispatch the fire department.

WARNING: This audio detector is intended only for use with smoke, carbon and combo detectors but it does

not detect the presence of smoke, heat, or fire directly.

ENROLLING

To enroll the sensor remove the top cover by depressing the friction tab in order to reveal the

battery. Pull and discard the battery plastic tab to turn on the device.

Download and install ClearSky App on your android or IOS phone.

Open your ClearSky APP and follow the directions on the app to learn in the sensor.

App will require you to press the learn button when linking (Image 1).

There are 2 modes of detection on the FireFighter™. Mode 1 is smoke only and Mode 2 is smoke and

carbon monoxide alert detection. To switch between modes, remove the battery, press and hold

the tamper switch and learn button until a red LED turns on. Let go of tamper and learn button. 1

red blink indicates smoke alert detection. 2 red blinks indicates smoke + CO alert detection.

MOUNTING

Included with this device is a mounting bracket, hardware and double sided tape. To ensure proper

operation ensure the side of the device with the small holes is directly facing the sounder holes on the smoke

detector. Secure the mounting bracket to the wall or ceiling using the two mounting screws and double

sided tape provided, then secure the audio detector to the mounting bracket using the small screw

provided. The FireFighter™ must be mounting within 6 inches of the detector for optimal operation.

WARNING: No

n-interconnected smoke detectors require an audio detector by each smoke detector sounder.

This equipment should be installed in accordance with Chapter 2 of the National Fire Alarm Code, ANSI/NFPA

72, (National Fire Protection Association, Batterymarch Park, Quincy, MA 02269). Printed information describing

proper installation, operation, testing, maintenance, evacuation planning, and repair service is to be provided

with this equipment. Warning: Owner’s instruction notice: ’Not to be removed by anyone except occupant’.

A Universal Electronics Com

PAGE 1
70 CS-602 AUDIO DETECTOR patent pending Installation Manual & Users Guide A Universal Electronics Company SPECIFICATIONS Frequency: 345MHz Operating Temperature: 32°-120°F (0°-49°C) Battery: One 3Vdc lithium CR123A Operating Humidity: 5-95% RH non condensing Battery life: up to 4 years Detection distance: 6 in max Compatible with 345MHz ClearSky Hub Supervisory signal interval: 70 min(approx.
PAGE 2
HOLES TO LINE UP WITH EXISTING SMOKE DETECTOR TAMPER SWITCH LEARN BUTTON IMAGE 1: ENROLLING / TEST / TAMPER BUTTON IMAGE 2: INSTALLATION DISTANCE IMAGE 3: SIDE MARKINGS TESTING To test the RF transmission from the mounted position you can either generate a tamper by removing the cover or press the learn button located next to the tamper switch. Press and release ONCE to send a Smoke signal or press and HOLD for 2 seconds to send a Carbon signal.
PAGE 3
PACKAGE CONTENTS Included Items: 1 x FireFighter™ Wireless Audio Detector 1 x Mounting Plate 2 x Mounting Screws 2 x Double Sided Tape 1 x CR123A battery 1 x Installation Manual FCC Compliance Statement This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. This device complies with part 15 of the FCC Rules.