User's Guide

ManualsBrandsEcolink Intelligent Technology ManualsElectronicsKey Fob

colink Intelligent Technology Inc. PN: CS102 Manual Rev 1.00

CS-102 Four Button Wireless Remote Users Guide and

Manual

The Ecolink 4‐Button Keyfob Remote communicates with the

ClearSky controller on the 345 MHz frequency. The keyfob is

a lithium coin cell, battery powered, wireless keyfob designed

to fit on a key chain, in a pocket, or in a purse. It gives users

the ability to turn the security system function ON and OFF

before entering the home or after exiting. When the control

panel and keyfob are configured, and there is an emergency,

you can turn on the siren and automatically call the central

monitoring station. Keyfobs can also operate control panel

auxiliary functions when configured.

It provides a convenient option for the following system

operations:

• Arm the system AWAY (all zones)

• Arm the system STAY (all zones except interior

follower zones)

• Arm the system with no entry delay (if programmed)

• Disarm the system

• Trigger panic alarms

Verify that the package includes the following:

• 1—4‐Button Keyfob Remote

• 1—Lithium Coin Battery CR2032 (included)

Figu

re 1: 4‐Button Keyfob Remote

ntroller programming:

Note: Refer to the latest instructions for the controller or

security system being used to learn in/program your new

keyfob.

Lea

rn In: When learning the keyfob into the ClearSky

controller, press the Arm Stay button and the Aux button

simultaneously.

ce the keyfob has been properly learned in, test the

keyfob by testing each of the keyfobs standard functions:

• Di

sarm button. Hold for two (2) seconds to disarm the

Control Panel. All zones except life safety are disarmed.

• Away button. Hold for two (2) seconds to arm the Control

Panel in Away mode. All zones are armed.

• Stay button. Hold for two (2) seconds to arm the Control

Panel in Stay mode. All zones except interior follower are

armed.

• Auxiliary button. If programmed, can trigger a pre‐selected

output. See the Control Panel’s Installation & Programming

Guide for details.

• Away & Disarm buttons. If programmed, pressing BOTH the

Away and Disarm buttons at the same time, will send one of

four types of emergency signals: (1)

auxiliary panic (paramedics); (2) audible alarm (police); (3)

silent panic (police); or (4) fire (fire department).

Programmable

Options

The Ecolink 4‐Button Keyfob Remote (Ecolink‐CS‐102) has

alternate programable configurations that can be enabled by

the end user.

To enter configuration mode:

Press and hold Arm Away button and AUX button at the

same time until led blinks.

Configuration option 1: Press the AWAY button to enable 1

second press required to send transmission from all buttons.

Configuration option 2: Press the DISARM button to enable a

3 second delay for the AUX button.

Configuration option 3: Press AUX button one time. (This sets

the keyfob for press and hold 3 seconds of the AUX button to

initiate panic alarm RF signal instead of holding the ARM

AWAY and DISARM buttons. NOTE: The panic RF signal is then

processed by panel. It will be 4‐5 seconds before audible

alarm. • Exit programming and test keyfob by pressing AUX

button for 3 seconds. Watch keyfob LED for a blink. This

indicates the RF signal has been sent to the panel. Alarm will

occur at this point.

Arm Away

Disarm

Arm Stay

Aux

Summary of content (2 pages)

PAGE 1
CS-102 Four Button Wireless Remote Users Guide and Manual The Ecolink 4‐Button Keyfob Remote communicates with the ClearSky controller on the 345 MHz frequency. The keyfob is a lithium coin cell, battery powered, wireless keyfob designed to fit on a key chain, in a pocket, or in a purse. It gives users the ability to turn the security system function ON and OFF before entering the home or after exiting.
PAGE 2
Warning: Changes or modifications not expressly approved Replacing the Battery When the battery is low a signal will be sent to the control panel, or when a button is pressed the LED will appear dim or will not turn on at all. Follow these simple steps to replace the battery 1. With a key or small screwdriver, push up on the black tab located at the bottom of the remote (fig.1) and slide the chrome trim off. 2. Carefully separate the front and back piece of plastic to reveal the battery 3.