User Manual

ManualsBrandsEcolink Intelligent Technology ManualsElectronicsWall Mounted Sensor

Ecolink Status Indicator

Model#: STAT433

Status Module Installation Manual and User Guide

Ecolink Bridge (Model#: BOOM433) - this is the main control units for this system. It must be located in

the same room but not more than 50ft of your Zwave gateway.

Status Module (Model#: STAT433) - this device provides the current status of the sensor installed on

your doors and windows. This should be located at your main entry/exit door (to check status as your

leave) or by your bedroom (to check status before you go to bed at night)

Door/Window sensor (Model#: DOOR433) - these are the sensors that you will mount on your doors

and windows. It will transmit back to the unit if the door/window is opened or closed.

Setup

The suggested process for configuring your system is as follows.

1. Power up the bridge

2. Enroll your door/window sensors

3. Enroll the status module

4. Install your door/window sensors

5. Test your system

6. Mount your status module

7. Include your Insynctive network into a Zwave gateway (optional)

Power up the bridge

Your Ecolink Bridge comes ready to plug into any standard electrical outlet.

However there are a number of jumpers located in the battery compartment that control the door

chime feature. You may want to adjust this prior to plugging it in as they are not accessible after you do

so.

The jumper options are as follows:

Volume Chime

J1 J2 J3 J4 Operation

off off X X Volume controlled by Z-wave GUI

off on X X Low volume

on off X X Med volume

on on X X High volume (default)

X X off off No chime

X X off on Chime when door or window is opened

X X on off Chime when door or window is unlocked

X X on on Chime when door or window is opened or unlocked (default)

The first time you plug in your bridge, the light will turn green, then start flashing blue.

Summary of content (5 pages)

PAGE 1
Ecolink Status Indicator Model#: STAT433 Status Module Installation Manual and User Guide Ecolink Bridge (Model#: BOOM433) - this is the main control units for this system. It must be located in the same room but not more than 50ft of your Zwave gateway. Status Module (Model#: STAT433) - this device provides the current status of the sensor installed on your doors and windows.
PAGE 2
Enroll Door/window sensors Unpack your sensors, including the magnet. Slide the top cover to disengage it from the bottom. Remove the top cover to reveal the battery. Remove the plastic tab that is installed underneath the battery. Ensure the battery is firmly in place. At this point you can decide to replace the white cover or switch to the brown cover. The brown cover, when installed, will cover the bottom piece so only brown is visible after installation.
PAGE 3
If successfully enrolled the status module will beep. Press the learn button on the bridge to exit this mode. At this point you can replace the battery cover of the status module. At this point, one of the bottom LEDs (open or closed) may be illuminated. This is showing the status of the sensor you have enrolled but have not yet installed. Installing and testing your sensors Your sensors come in two parts, the actual transmitter and the magnet.
PAGE 4
Include your Insynctive network into a Z-wave Gateway (optional) To successfully operate with a Z-wave gateway, the Ecolink bridge must be located in the same room but no more than 50ft of your Z-wave gateway. To include your system, disconnect the Ethernet cable from the back or your gateway. Unplug your Ecolink Bridge. Press the include (or +) button on the gateway.
PAGE 5
FCC Compliance Statement This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.