Certification Exhibit FCC ID: Z9O-FAS1509 IC: 10060A-FAS1509 FCC Rule Part: 15.249 IC Radio Standards Specification: RSS-210 ACS Project: 11-2105 Manufacturer: UltraClenz, LLC Models: FAS1509-00, FAS1509-01, FAS1509-02, FAS1509-03, FAS1509-04 User Manual 3998 FAU Blvd.
Patient Safeguard System (PSS) Healthcare Worker Badge User’s Guide DOC1046 Revision 1 UltraClenz, LLC
Patient Safeguard System – Healthcare Worker Badge User’s Guide UltraClenz, LLC Table of Contents Revision History ......................................................................................................................................................... 3 1.0 Introduction to the System .................................................................................................................................. 4 2.0 System Components .....................................................
Patient Safeguard System – Healthcare Worker Badge User’s Guide UltraClenz, LLC Revision History Revision Date By 0 3/14/12 MES Initial Release 1 08/09/12 DLS Corrected TOC and replaced FCC class A statement with class B statement Description Page 3
Patient Safeguard System – Healthcare Worker Badge User’s Guide UltraClenz, LLC 1.0 Introduction to the System The Patient Safeguard System (PSS) was designed to help Healthcare Workers (HCW) protect their patients from the unintentional spread of pathogens. This is achieved by providing a tool to remind HCWs to perform hand hygiene when the opportunities are presented.
Patient Safeguard System – Healthcare Worker Badge User’s Guide UltraClenz, LLC Each indicator LED (green, yellow and red) represents the current level or state of the HCW’s hand hygiene compliance. Each badge has a uniquie programmed identification adress. For group monitoring, badges are not assigned to a particular HCW. For individual monitoring, badges are assigned to a designated HCW. Figure 1.
Patient Safeguard System – Healthcare Worker Badge User’s Guide UltraClenz, LLC 3.0 How the System Works When a Healthcare Worker (HCW) begins their shift, they will attach an assigned badge to their clothing in a location above the waist that is clearly visible to HCW as well as others. The badge will be dormant with no blinking LED visible. This is normal because the badge will go into a “sleep” state to conserve battery power when not in use for a period of 30 minutes or more.
Patient Safeguard System – Healthcare Worker Badge User’s Guide UltraClenz, LLC will change to the warning state. The badge will produce 3 quick beep tones with the second tone being lower in pitch than the first or third tones. This indicates successful communications between the badge and the bed beacon located within the patient zone. The badge’s red LED will then blink about once every 1.5 seconds.
Patient Safeguard System – Healthcare Worker Badge User’s Guide UltraClenz, LLC 4.0 Installing the System 4.1 Healthcare Worker (HCW) Badge Installation This is to be worn by the HCW. For best performance, the badge should be worn above the waist in a location that is clearly visible to the HCW as well as the patients and other healthcare staff. The badge was designed to easily attach to a lanyard or a vinyl strap and clip.
Patient Safeguard System – Healthcare Worker Badge User’s Guide UltraClenz, LLC Appendix A - System Component Care and Maintenance Cleaning the Components The badge, bed beacon and dispenser beacon should be cleaned by wiping with a soft cloth. A mixture of 90% water and 10% chlorine (bleach) or water and mild detergent (dish soap) may be used. The cloth should be damp but not wet. Only the exterior of each component may be cleaned.
P Patient Safeg guard System m – Healthca are Worker Badge B User’s s Guide UltraCllenz, LLC B Battery Repla acement H Healthcare W Worker (HCW W) Badge The badge is powered by a single 3 voltt coin cell batttery (CR2032 T 2). The PSS software s mon nitors the badg ge battery g good/low statu us flag to ind dicate when a replacement is required.
Patient Safeguard System – Healthcare Worker Badge User’s Guide UltraClenz, LLC Healthcare Worker Badge Power On Self Test (POST) Insert the new 3VDC coin cell battery into the battery holder on the PCB1034. Observe and verify the sequential LED functions below. If the PCB fails any of the steps below, set it aside for inspection and rework. 1. As the PCB powers up, it performs a power on self test (POST). The red, yellow and green LED will flash once each in consecutive order.
Patient Safeguard System – Healthcare Worker Badge User’s Guide UltraClenz, LLC Appendix B - Certification and Safety Approvals FCC THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Patient Safeguard System – Healthcare Worker Badge User’s Guide UltraClenz, LLC Warranty This device is warranted against defective materials and workmanship for one year from the date of delivery. Equipment covered by this warranty will be repaired or replaced in the United States and Canada, WITHOUT CHARGE, except for shipping and handling, by our Factory Service Center.