Bentley WiNET Gateway User Guide FAS1506 DOC1038 Revision 0
Document Title UltraClenz, LLC Table of Contents Revision History ......................................................................................................................................................... 3 Box Contents ............................................................................................................................................................. 4 Overview ..........................................................................................................
Document Title UltraClenz, LLC Revision History Revision Date By 0 01/25/11 MJB Description Initial Release Page 3
D Document Title UltraC Clenz, LLC B Contents Box 1 WiNET Ga ateway (with Antenna) A 1 Power Sup pply 4 Screws an nd Anchors 1 User’s Guiide O Overview The FASxxxxx WiNet Gateway, when used T u as a com mponent of th he WiNet wirreless monito oring solution, receives r radio transmisssions from both b the WiNe et Hub and th he WiNet Tag. The WiNet Gateway is can c work with h a router, p providing acce ess to a remo ote server.
Document Title UltraClenz, LLC Installing the Gateway This procedure will require a small hammer, drill, drill bits, level and a screw driver. Step 1 – Positioning the Chassis Place the leveled Gateway on the mounting location to transfer the drill centers. Step 2 – Drilling the Holes Drill 4 holes with the proper bit. Use standard bits for dry wall and masonry bits for tile applications. Step 3 – Placing the Anchors Gently tap the anchors in place using a hammer.
Document Title UltraClenz, LLC Step 2 – Inserting the Power Supply Wires With the small flat-tip screwdriver in place, insert the wire with the white stripe on it from the power supply (positive wire) (see Figure 3) into the circular opening directly beneath the rectangular slot until it stops and pull out the small flat-tip screwdriver to lock the wire in place. Give the positive wire a slight tug to insure that it is locked into place.
Document Title UltraClenz, LLC Step 2 – Connect Ethernet Cable to Router Take the RJ-45 connector of the other end of a category 5e Ethernet cable and insert it into the Ethernet port on the router. (see Figure 5). Figure 5 The finished assembly should resemble Figure 6. Figure 6 Configuring the Gateway Configuring the Gateway requires a third party terminal emulation program. For the purposes of this manual, we will use HyperTerminal by Microsoft.
Document Title UltraClenz, LLC Step 1 – Create a HyperTerminal connection for the Gateway a) b) c) Click on File > New Connection, type the name your connection, click on OK. In the Connect to dialogue box, select the appropriate COM port in the Connect using field, click on OK. Use the values in Figure 7. to configure the properties of the COM port in the following dialogue box and click OK. Figure 7 This brings up the HyperTerminal main screen shown at Figure 8.
Document Title UltraClenz, LLC Step 2 – Configuring the Gateway through HyperTerminal. a) b) c) d) e) f) Set the time on the Gateway by typing ‘T’ followed by the date/time group using the following syntax; t yyyy-mm-dd hh:mm:ss [enter] (example: t 2011-01-18 20:32:40) With the Gateway connected to the Router (see Figures 5 and 6) type ‘C’ [enter] to show the Gateway’s current network configuration Type “CD 1” [enter] to enable Dynamic Host Configuration Protocol (DHCP).
Document Title UltraClenz, LLC Maintenance of the Gateway Cleaning The exterior can be cleaned with a NON abrasive detergent and a NON abrasive damp (not wet) sponge or cloth. The Hub is splash resistant but not water proof.
Document Title UltraClenz, LLC Certification and Safety Approvals FCC This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Document Title UltraClenz, LLC Warranty This device is warranted against defective materials and workmanship for one year from the date of delivery. Equipment covered by this warranty will be repaired or replaced in the United States and Canada, WITHOUT CHARGE, except for shipping and handling, by our Factory Service Center.
