Bentley WiNET Tag User Guide FAS1503 DOC1036 Revision 0
Document Title UltraClenz, LLC Table of Contents Revision History ................................................................................................................................................... 3 Box Contents ....................................................................................................................................................... 4 Overview ......................................................................................................................
Document Title UltraClenz, LLC Revision History Revision Date By 0 01/25/11 MJB Description Initial Release Page 3
Document Title UltraClenz, LLC Box Contents 1 WiNET Radio Tag 2 Coin Cell Batteries (CR2430 - Optional) 1 Detachable Cable 1 User’s Guide Overview The FAS1503 WiNet Tag, when used as a component of the WiNET wireless monitoring solution, relays radio transmissions to both the WiNET Hub (FASxxxx) and the WiNET Gateway (FASxxxx) (see Figure 1). Figure 1.
Document Title UltraClenz, LLC Installing the Batteries This procedure will require a small Phillips screwdriver. Step 1 – Open Tag Enclosure With a small Phillips screwdriver, remove the two screws located on the front of the Tag enclosure (see Figure 2). With the screw removed, separate the bottom half of the Tag enclosure from the top half. The Tag will be secured inside the Tag enclosure.
Document Title UltraClenz, LLC Installing the Tag This procedure will require no tools. Step 1 – Tag Mounting Location In a dry indoor environment, locate an area on a wall next to the dispenser where the Tag will be mounted, preferably to the immediate right or left of the dispenser. Make sure the wall’s surface is clean and free of dirt, dust or grease. NOTE: The Tag is a radio and therefore should not be mounted on or near large metal objects. Doing so may degrade its performance.
Document Title UltraClenz, LLC Connecting the Tag to the Dispenser Step 1 – Remove Touch-free Dispenser Gearbox Open the cover of the dispenser and remove the touch-free gearbox. To remove the touch-free gearbox, depress the retention clip located at the top of the touch-free gearbox to unlatch and pivot forward to remove. Step 2 – Install Cable Locate the 6-pin port on the back of the touch-free gearbox and insert the free end of the detachable cable into the port (see figure 7).
Document Title UltraClenz, LLC Step 3 – Install Gearbox back into the Dispenser To reinstall the touch-free gearbox, place the bottom 2 pivot points into the chassis base and pivot the top towards the chassis until the touch-free gearbox latches and clicks into place. Close the cover. The finished installation should look like Figure 9 below.
Document Title UltraClenz, LLC Step 3 – Conducting the Test With the Gateway properly connected to computer through the USB to RS485 Network Interface adapter, activate the dispenser. Successful events will appear on terminal session as seen in figure 11. Test the connection between the Gateway and the Computer by pressing the letter “t” [enter]. You will see the current date time group that is configured on the Gateway.
Document Title UltraClenz, LLC 09520009 = Gateway assigned to that network Maintenance Cleaning The exterior can be cleaned with a NON abrasive detergent and a NON abrasive damp (not wet) sponge or cloth. The Tag is splash resistant but not water proof. Changing the Batteries This procedure will require a small Phillips screwdriver and two (2) coin cell batteries (CR2430). Step 1 – Open Tag Enclosure With a small Phillips screwdriver, remove the two screws located on the front of the Tag (see Figure 2).
Document Title UltraClenz, LLC Certification and Safety Approvals FCC This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Document Title UltraClenz, LLC Warranty This device is warranted against defective materials and workmanship for one year from the date of delivery. Equipment covered by this warranty will be repaired or replaced in the United States and Canada, WITHOUT CHARGE, except for shipping and handling, by our Factory Service Center.