Quick Start Guide

Draft
Ecobee Quick Start Guide
1 Activate your Room Sensor.
Use the ecobee app to add your new Room Sensor.
Scan the QR code then pull the tab to activate your device.
2a Place it on a table.
Use the stand to place your sensor on a table or shelf. If you’ve
picked a spot that’s higher than 4 feet, use the wall-mount.
2b Or stick it to the wall.
Stick your Sensor to the wall using the wall-mount.
Handy for curious children or pets.
3 Explore the features you’ve
unlocked on your ecobee.
SMART HOME/AWAY
Sensors adjust temperature for comfort if
you’re home, and savings if you’re not.
FOLLOW ME
Sensors keep track of what room you’re in
to focus comfort where it matters most.
THERMAL PROTECT
Get abnormal temperature alerts.
Find out more at ecobee.com/room-sensors
Model No: EBERS41
FCC ID: WR91881541519
IC: 7981A-1881541519
Power source: CR2477 battery
Operating Temperature: 0°C to 40°C
Operating Humidity: 20% to 80% RH
FCC Compliance Statement
Compliance Notice:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment o_
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment
and receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of FCC rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause
undesired operation.
Changes or modifications that are not expressly
approved by the manufacturer could void the
user’s authority to operate the equipment.
RF Exposure Information:
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. In order
to avoid the possibility of exceeding the FCC radio
frequency exposure limits, human proximity to the
antenna shall not be less than 20cm during normal
operation.
Innovation, Science and Economic Development Canada (ISED) |
Compliance Notice:
This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference, including
interference that may cause undesired operation of the
device.
Innovation, Sciences et Développement économique Canada (ISDE)
| Avis de conformité:
L’émetteur/récepteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
RF Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set
forth for an uncontrolled environment. This transmitter must be
installed to provide a separation distance of at least 20 cm from all
persons and must not be collocated or operating in conjunction with
any other antenna or transmitter.
Warning: Changes or modifications not expressly approved by ecobee
Inc. could void the user’s authority to operate the equipment.