Iridium Satellite LLC 8440 South River Parkway Tempe, AZ 85284 USA Tel. Toll Free 1-866-947-4348 Local or International 1-480-752-5155 E-mail info@iridium.
ii 0125
Handset What Is What? 1 2 3 4 5 6 7 1. Display 2. Indicator lamps Power Call Network 3. Escape key 4. Call transfer key 5. Loudspeaker on/off key 6. Shift key 7. Lock on/off key 0125 8 9 10 11 12 13 14 15 16 17 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
Introduction Returning to Idle State on an Enabled CU: Congratulations on your new Iridium equipment. 1. Press Your Iridium equipment is a modular system that consists of an antenna, transmitter/receiver, control handset and/or fixed control unit, and optional PSTN telephone/PBX. You can operate the Iridium equipment in voice mode from a control handset, fixed control unit, and/or PSTN telephone.
Contents Handset ................................................................................ iii What Is What? ............................................................................. iii Introduction ......................................................................... iv About this Manual .............................................................. iv Iridium Satellite System ...................................................... 1 Abbreviations ...........................................
Using a Telephone To your Iridium equipment, you can connect a PSTN telephone or a PBX. Many of the system’s more advanced features, like the security lock function, are however not accessible from a telephone. Neither is any SIM card action. Therefore, when using the telephone, the SIM card has to be operational. This means that the pin code has to be disabled on the card, or the pin code must be entered from a CU before the telephone is used.
Handset Simple Operation Enter PIN To the Iridium system you can connect up to four handsets. A handset can be in one of two states: enabled or disabled. 7/9/1999 12:00:48 Handset States In each of the two states, the handset’s normal display and signalling can be described as follows: Key in the pin code supplied with the SIM card (see the installation manual).
1. Handset removed from hook, but hooked on by hook key. 2. To find the right user name on the list, eg. Commander, use: 2. Hook off. 3. No icon: Handset placed in hook, and hook on. Volume During a conversation, the speaker and earpiece volume can be adjusted by means of: 3. Confirm: Password for Commander _ 4. Key in the password that corresponds to the selected user name. Manual Telephone Call Syntax 5.
For internal calls, entering a telephone number on the handset follows the syntax of this example: 1. Hook off either by removing the handset from the hook or by pressing the hook key Enter number _ Type 0 for ext. calls or Enter number _ Internal calls only 2. Use the numeric keys to key in the number you want to dial. 2. Internal number, e.g. 344 3.
Answering a Call NOTE: When the speaker is off you can see that you are being called, (the display will show “Incoming Call”) but there will be no sound in the speaker. The speaker can be toggled on and off using: 2. Now, key in the extension number to which the call should be transferred. 3. To transfer the call, press: Call is transferred 1. When the handset rings, remove it from the hook and communicate as on an ordinary telephone. 2.
Handset Advanced Operation 4. To select “Enable” or “Disable”, use : and press: The system features a large number of special functions. For those of the functions that are likely to be used the most, there are special buttons or shifted functions in connection with the numeric keys. The functions used less often can be found in the menu system. Menu System The function has now been enabled or disabled depending on your choice.
for instance, will give a “D”; pressing the key twice, will give an “E”, etc. 1st push: D 2nd push: E 3rd push: F 4th push: d 5th push: e 6th push: f 7th push: 2 control unit tries to enter one of these modes, and another control unit has done the same, the display will show: Phone book occupied. The phone book can always be entered from an enabled and unlocked CU which is in idle state. See section “About this Manual” on how to return to idle state.
Changing a Number Stored in the Phone Book 6. Key in the number using of the numeric keys. To edit a stored number in the phone book: 7. To store the number, press: 1. To enter the phone book, press: Deleting a Stored Entry in the Phone Book 2. To select the desired entry in the phone book, press: 3. To enter the shifted functions, press: 1. To enter the phone book, press: 2. To select the desired entry in the phone book, press: 4. To select the edit mode, press: 3.
Redialling User ID/User Name List It is possible to redial the last number dialled by the current user. To do so: Every user specified in the system is given a priority value. The priority value determines what the user is allowed to do in the system. By default, the user list contains 6 entries with different priority values. The 6 default users are shown below. 1. Hook off. User ID/User Name 2. Press: SUPER USER Captain Commander Officer Crew Passenger 3. Press: 4.
4. Find the “Disable” item using : and press: 3. Find the “Lock” item using: and press: 4. To select the “Enable” item, press: 5. Find the right user name using: 5. Find a user name of priority level 4 or less, using: and press: 6. Key in the password, and press: The security lock function is now disabled. This means that the handset is ready for use for everyone without any identification of the user.
2. To select the “Setup” item, press 5. Key in the new user name, and confirm by 6. Key in the password, and confirm by 3. To find the “Password” item, use: A new user has now been added to the system with a default priority. The priority is one of the properties that can be edited using the procedure described next. 4. To confirm, press: Editing the Properties of an Existing User: 1. To enter the function menu, press: 5. Key in the old password and confirm by pressing 2.
Viewing the Last Private Call Log: The call log for the current user can be retrieved as shown in the following: 2. To select the “Setup” item, press: 1. To enter the function menu, press: 3. To find the “Users” item, use and confirm by 2. Find the item “Call Log” using and confirm by 4. To find the user to be deleted, use: 3. Find the item “Private” using and confirm by 5. To delete the user, press 6. Confirm by 4.
2. Find the item “Call Log” using and confirm by Now, find the user by means of and press Setting Time and Date 3. Find the item “Global” using and confirm by A list of all outgoing calls made from the system can now be retrieved by choosing the item “Outgoing” and pressing To see more details about a specific call, find the call using Time and date can be displayed and adjusted manually. The time is used in the call log.
Sys. update: If this option is chosen, the time written in the display is updated using only the internal circuitry of the RTU itself. Consequently, if your Iridium system is turned off and the on again, the clock will be reset to a default time. The correct time must then be set again manually each time. To enable or disable the light, select the On or Off item respectively. To adjust the dimmer level, select the Level item.
Display For each handset, the user may select the information to be shown in the display when the handset is in idle state. However, the state of the system will always be shown in the display. The available choices are: • • • • Time/date: Both the time (hours, minutes, seconds) and the date is shown. Time: Only the time (hours and minutes) is shown. Position: If a GPS receiver is connected to the transceiver, choosing “Position” will show the geographic position in terms of latitude and longitude.
and press: 1. Key in the 4-8 digit PIN code and press: Changing the PIN Code 3. Find the “SIM Card” item using: 1. To enter the function menu, press: and press: 2. Find the “System” item using: 4. Find the “PIN enable” item using: and press: and press: 3. Find the “SIM Card” item using: 5. Key in the PIN code and press: and press: Disabling the PIN code Follow steps 1 – 5 above with the following substitution: 4.
Unblocking a Blocked SIM Card If a wrong PIN code has been entered 3 times in a row, the RTU blocks the SIM card. If a blocked SIM card is inserted into the SIM card holder or if a SIM card already in the SIM card holder is blocked, the display will show “SIM Card blocked” when the CU is in idle state. In order to unblock a blocked SIM card: Follow step 1 – 3 above. 4. Find the “PUK Code” item and press: 5. Enter the correct PUK code and press: 6.
1. To enter the function menu, press: 3. Find the item “Call Answer” using and press: 2. To select the “Setup” item, press: 3. Find the “Extension” item using and press: 4. Key in a number below 10,000 that is not in use by any other 4. Find the item “One CU” using and press: 5.
• • Forward all calls: All external incoming calls will immediately be forwarded to the number you specify when you activate this category. Forward on not reachable: When your Iridium equipment has been turned off or cannot for some reason be contacted by the network or when the line of your Iridium equipment is occupied, either by an internal or an external call, external incoming calls will be forwarded to the number you specify when you activate this category.
You may record a personal greeting which the callers will hear when they are forwarded to your mailbox. After hearing your personal greeting, callers can leave a voice mail message which is stored in your mailbox. Your personal mailbox has a lot of features which can be configured by you. The caller also has a number of facilities to choose between when forwarded to your mailbox. See the “Iridium Services User Guide” that comes together with your Iridium equipment.
To switch between two calls: 2. Call Hold [ old password] [new password] NOTE: This feature is only available with RTU software version 3.0.0 and higher. Contact your service provider to find out when this feature will become available. [new password] Putting a call on hold allows you to place a second call without ending the first. To put the current call on hold and place a second call: Call Waiting NOTE: This feature is only available with RTU software version 3.0.0 and higher.
Activate: 1. Hook off 2. Establish a call to the first party. For each new party to add to the conference call, do the following: 3. [telephone number of next party] 3. Find the item “SW version” using 4. and press: Choose the hardware whose software version you want informa- tion on, using and press: To end the conference call, press: Resetting Primarily for service and test purposes, it is possible to reset your Iridium equipment to force it into a well-defined state.
Tone Signalling 4. Find the item “Restart” using and press: The system will give you information on its status as well as instructions by means of tone signalling. This is done on four different frequencies: 450, 900, 1440 and 1800 Hz. Appendix A illustrates what the various tone signalling sounds like. 5.
Appendix A Tone Signalling 1800 Hz 1440 Hz 900 Hz 450 Hz 1 sec.
Appendix B Function Menu Overview To access the function menus, press: To move about in the menus, use the arrow keys: To confirm that you want to select an item, use the OK key: To regret the last step, use the Escape key: Functions marked with an asterisk (*) concern the specific handset. All other functions are global, i.e. they concern the whole system. The following table contains a total list of the entries in the function menu system.
Menu Setup 1st submenu Ringing tone Ring test 2nd submenu Deep High Slow alt. Fast alt. External Internal Ring vol. (*) Speaker vol. (*) Key beep (*) Enable Disable Volume Lock Enable Disable Password Users Userlist + Add Userlist + Edit Userlist + Del.
System Time/date SW versions Call answer SIM Card Reset Show Set Sys.update GPS update Transceiver LBT Ctrl unit Status All One CU PSTN PIN enable PIN disable Change PIN PUK code Restart Factory res Shows the time and date. Sets the time and date. Sets the system to update the time and date. Sets the GPS to update the time and date. Displays the software version number of the transceiver. Displays the software version number of the LBT. Displays the software version number of the handset.
EuroCom Industries A/S Porsvej 2 DK-9200 Aalborg SV Denmark Tel. Fax E-mail +45 7013 7000 +45 4474 8501 eci@eci.