#YourGearUpgraded Full Motion TV Wall Mount Model EGMF1 INSTRUCTION MANUAL
IMPORTANT SAFETY INSTRUCTIONS. READ ENTIRE MANUAL PRIOR TO USE. SAVE These INSTRUCTIONS Yea, the boring stuff ... but read it, so you don’t jack things up! Please read through these instructions completely to be sure you’re comfortable with this easy install process. Also check your TV owner’s manual to see if there are any special requirements for mounting your TV.
Verify Your Wall Construction CAUTION: ? wood studs? DO NOT install into drywall alone Contact The Echogear Pros at 1-855-428-2490 or www.echogear.com Perfect! to ou WANT ... unless y r TV fall and watch you the floor. crash onto UUUUHHH ?!? Unsure? Good to Go Grab Your Tools Toy Surprise Stud Finder Awl Tape Measure Pencil Level FREE Inside Every Box HK Hex Key 4mm k bac e it when v i "G Phil h" to finis you Phillips Screwdriver 7/32 in. (5.
One More Thing ... Echogear Satisfaction Guarantee: We’re driven to give DIYers an awesome install experience. We stand behind everything we make because you deserve the best entertainment experience without sacrificing quality and spending your whole paycheck. Guess what? We’ll help you through the entire process, too. Why? Because we like to help and it’s our passion to provide authentic service. We won’t leave you hanging, no matter what. Our U.S.
What’s in the Box WARNING: DON'T FEED TO CHILDREN — This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts! NOTE: Not all hardware included in this kit will be used. STUFF FOR STEP 1 01 M4 TV Screws (qty.
More STUFF FOR STEP 1 Parts for TVs with Large Mounting Hole Patterns: Wall Plate / Arm F Face Plate (attached) Extender Bracket Screws Extender Brackets M6 x 8mm M6 x 8mm 04 05 qty. 1 Screws S (attached) qty.2 07 06 qty.8 qty.2 STUFF FOR STEP 2 Lag Screw 09 08 qty. 2 6 Washer 5/16 x 2¾ in. 5/16 x 2¾ in. qty.2 (For Lag Screw) 5/16 in. 5/16 in.
STEP 1 Attach the TV BRACKET TO YOUR TV STEP 1.1 Select TV Screws a Only one screw size fits your TV. M4 M6 M8 r d uses fo screws: the extra "Suggeste s, me piece board ga , l jewelry industria , rn holders sweet co n e ts – strum musical in cas or like mara n' sticks, 'monsoo Select Spacers (if needed) STEP 1.
STEP 1.3 Remove Face Plate F Measure TV Hole Pattern STEP 1.4 Width 04 mm inches cm mm 4 5⅛ 7⅞ 11 ¾ 13 ¾ 15 ¾ 10 13 20 30 34 40 100 130 200 300 340 400 x f us hose o "For t ath" ATE m that H inch dimensions are approximate HK S IMPORTANT: Save screws 8 F S for use in STEP 3.
A Configure TV Bracket to Fit Your TV Hole Pattern 200mm x 200mm or LESS . here .. " to do g in EP 1.6 h T t "No . to S .. g n it alo move 200 mm (7 ⅞ in.) 130 mm (5 ⅛ in.) 100 mm (4 in.) B MORE than 200mm x 200mm 400 mm (15 ¾ in.) 340 mm (13 ⅜ in.) 300 mm (11 ¾ in.) 200 mm (7 ⅞ in.) 130 mm (5 ⅛ in.) 100 mm (4 in.) F ASSEMBLE 06 05 07 300 mm (11 ¾ in.) 340 mm (13 ⅜ in.) 400 mm (15 ¾ in.) STEP 1.5 F qty.
STEP 1.6 Secure the TV Bracket to Your TV F a No Spacer b With Spacer 01 02 01 02 CAUTION: Ensure the TV bracket is CENTERED on your 10 TV AND securely fastened in place.
STEP 2 I nstall the Wall Plate CAUTION: Avoid potential personal injuries and property damage! Min. Wood Stud Depth: nominal 4 in. (102 mm) actual 3 ½ in. (89 mm) STEP 2.1 Find a Stud ay X-Recs Sp ld so tely ara p se Min. Wood Stud Width: nominal 2 in. (51 mm) actual 1 ½ in. (38 mm) Max. Drywall: 5/8 in. (16 mm) Drywall covering the wall must not exceed 5/8 in. (16 mm). Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1 ½ x 3 ½ in. (38 x 89 mm). Use a stud finder ...
STEP 2.2 Mark STEP 2.3 Drill Secure Wall Plate STEP 2.4 08 2¾ in. (6.9 cm) 09 04 7/32 in. Bit (5.5 mm) This End UP 04 12 CAUTION: Avoid potential personal injury or property damage! Lag screws 08 MUST BE firmly tightened to prevent unwanted movement of the wall plate/arm 04 .
STEP 3 Hang Your TV HEAVY! You may need assistance with this step. F rs that iend of you "Ask that fr ssFit" ro C t n abou yammers o CAUTION: Avoid potential personal injury or property damage! Screws S MUST be installed to secure your TV to wall plate/arm 04 .
ADJUSTMENTS Tilt TO ADJUST THE TILT TENSION, first rotate (tighten or loosen) the tilt lever T as far as you can, then: a Pull and hold the lever T outward, b Rotate the lever T in the opposite direction, c Release the lever T back into position, d Rotate the lever T to tighten or loosen. Repeat as needed. LOOSEN: to adjust the TV tilt position. TIGHTEN: to set the TV in place at your desired tilt angle.
Level REMOVE YOUR TV 1. Loosen the two screws S on the rear of arm 04 , using the hex key HK . 2. Level your TV. HEAVY! You may need assistance with this step. "Don't be a hero!" 3. Retighten screws S to secure in place.
“Wanna show off your hard work? Share a picture of your completed project with #YourGearUpgraded. Who knows, it might not be as bad as you thought” Confuzzled? Contact the ECHOGEAR Pros: 1-855-428-2490 helpmehelpyou@ECHOGEAR.com ECHOGEAR.com Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete.