Operator’s Manual PB-9010 H/T Power Blower The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Read and understand all provided literature before use. Failure to do so could result in serious injury. This product complies with CAN ICES-2/NMB-2.
TABLE OF CONTENTS PB-9010 H/T TABLE OF CONTENTS Table of Contents ........................................................................................ 2 Introduction ................................................................................................. 3 Servicing Information .................................................................................. 3 Parts/Serial Number............................................................................. 3 Service ..........................
PB-9010 H/T INTRODUCTION INTRODUCTION Specifications, descriptions and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accessories, and may not include all standard equipment. Read and understand all provided literature. Literature contains specifications and information for safety, operation, maintenance, storage, and assembly specific to this product.
SERVICING INFORMATION PB-9010 H/T Service Service of this product during the warranty period must be performed by an Authorized ECHO Service Dealer. For the name and address of the Authorized ECHO Service Dealer nearest you, ask your retailer or call: 1-800-432-ECHO (3246). Dealer information is also available on our Web Site www.echo-usa.com. When presenting your unit for Warranty service/ repairs, proof of purchase is required.
PB-9010 H/T SAFETY SAFETY Manual Safety Symbols and Important Information Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages preceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to you. The safety alert symbol accompanied by the word “DANGER” calls attention to an act or condition which WILL lead to serious personal injury or death if not avoided.
SAFETY PB-9010 H/T International Symbols Symbol Description Read and Understand the Operator’s Manual Wear Eye, Ear and Head Protection Wear Hand Protection Safety/Alert Symbol H T L STOP Description Carburetor Adjustment - High Speed Mixture Carburetor Adjustment - Idle Speed Carburetor Adjustment - Low Speed Mixture Stop Switch STOP 6 Hot Surface Fuel and Oil Mixture Idle speed Fast speed Finger severing Purge Bulb DO NOT Allow Flames or Sparks Near Fuel Ignition ON / OFF DO NOT Smoke
PB-9010 H/T Symbol SAFETY Description Symbol Description Choke Control “RUN” Position (Choke Open) Wear Slip Resistant Footwear Beware of thrown objects Keep Bystanders and Helpers Away 15 m (50 ft.). Note: Not all symbols will appear on your unit. Personal Condition and Safety Equipment Cancer and Reproductive Harm www.P65Warnings.ca.gov The muffler or catalytic muffler and surrounding cover may become extremely hot.
SAFETY PB-9010 H/T Physical Condition Your judgment and physical dexterity may not be good: • If you are tired or sick • If you are taking medication • If you have taken alcohol or drugs Operate unit only if you are physically and mentally well. Eye Protection ◆ ◆ Eye protection that meets ANSI Z87.1 or CE requirements must be worn whenever you operate the unit.
PB-9010 H/T SAFETY • DO NOT WEAR TIES, SCARVES, JEWELRY, or clothing with loose or hanging items that could become entangled in moving parts or surrounding growth. • Keep clothing buttoned or zipped, and keep shirt tails tucked in. • Wear sturdy work shoes with nonskid rubber soles. • DO NOT WEAR OPEN TOED SHOES. • DO NOT OPERATE UNIT WITH BARE FEET. Keep long hair away from engine and air intake. Retain hair with cap or net.
SAFETY PB-9010 H/T • Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by not smoking. • Limit the hours of operation. Try to fill each day with jobs where operating the unit or other hand-held power equipment is not required. • If you experience discomfort, redness, and swelling of the fingers followed by whitening and loss of feeling, consult your physician before further exposing yourself to cold and vibration.
PB-9010 H/T SAFETY All over head electrical conductors and communications wires can have electricity flow with high voltages. This unit is not insulated against electrical current. Never touch wires directly or indirectly, otherwise serious injury or death can result. Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death.
SAFETY PB-9010 H/T Equipment Use only approved attachments. Serious injury can result from the use of a non-approved attachment combination. ECHO, INCORPORATED will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual. ◆ Do not attempt to modify this product. Serious injury can result from the use of any modified product.
PB-9010 H/T EMISSION CONTROL EMISSION CONTROL (EXHAUST & EVAPORATIVE) CARB And EPA Emissions Control Information The emission control system for the engine is EM (engine modification) and, if the second to last character of the Engine Family on the Emission Control Information label (sample below) is “B”, “C”, “K”, or “T”, the emission control system is EM and TWC (3way catalyst). The fuel tank/fuel line emission control system is EVAP (evaporative emissions).
DESCRIPTION PB-9010 H/T DESCRIPTION PB-9010 H Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your dealer. The safety decal is for example only. Your label may appear slightly different.
PB-9010 H/T DESCRIPTION PB-9010 H 1. Handle 2. Throttle Position Lever / Stop Switch 3. Air Cleaner 4. Shoulder Harness 5. Safety Decal 6. Stick Handle 7. Blower Pipes 8. Flexible Pipe 9. Spark Arrestor Muffler (with or without Catalyst) 10. Fuel Tank 11. Cold Weather Insert 12. Fuel Tank Cap 13. Spark Plug 14. Choke 15. Recoil Starter Handle 16.
DESCRIPTION PB-9010 H/T PB-9010 T Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your dealer. The safety decal is for example only. Your label may appear slightly different.
PB-9010 H/T DESCRIPTION PB-9010 T 1. Air Cleaner 2. Shoulder Harness 3. Safety Decal 4. Handle 5. Throttle Position Lever 6. Throttle Trigger 7. Blower Pipes 8. Flexible Pipe 9. Spark Arrestor Muffler (with or without Catalyst) 10. Fuel Tank 11. Cold Weather Insert 12. Fuel Tank Cap 13. Spark Plug 14. Choke 15. Recoil Starter Handle 16.
CONTENTS PB-9010 H/T CONTENTS The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, some assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts.
PB-9010 H/T ASSEMBLY ASSEMBLY PB-9010 H Never perform maintenance or assembly procedures with engine running or serious personal injury can result. Install Blower Pipes and Stick Handle 1. Assemble clamps (A) onto both ends of flexible pipe (B). A B 2. A Insert anti-static wire through flex tube, into swivel pipe.
ASSEMBLY 3. Assemble swivel pipe (C) into flexible pipe (B). 4. Assemble flexible pipe (B) to elbow (D) on blower and tighten clamps (A). Note: A light lubricant may be used to ease assembly of flexible pipe to blower elbow. 5. Loosen knob (E) completely and expand stick handle clamp. Align wire (G) in handle with grounding strip on swivel pipe (C). 6. Slide stick handle onto swivel pipe (C). Stick handle (F) should be angled away from operator. 7. 8. 9.
PB-9010 H/T ASSEMBLY Note: Blower use will eventually loosen pipe connections. Exclusive positive locking system allows pipes to be tightened. If loosening occurs, remove two pipes and install according to steps 8 and 9. PB-9010 T Never perform maintenance or assembly procedures with engine running or serious personal injury may result. Install Blower Pipes 1. Assemble clamps (A) and (G) onto both ends of flexible pipe (B). Note: Clamp with cable guide loop (G) fits elbow end of flexible pipe. 2.
ASSEMBLY 3. PB-9010 H/T Assemble flexible pipe to elbow (D) on blower. Position clamp with cable guide loop (G) on outside of flexible pipe and tighten clamp. C Note: Hang handle freely from blower to assure throttle cable is not twisted before installing handle (E). D G 4. Position throttle cable along the outside of elbow. Loosen knob (H) on handle (E). Install onto swivel pipe (C). 5. Insert anti-static wire into swivel pipe. 6. Assemble swivel pipe into flexible pipe and tighten clamp (A). 7.
PB-9010 H/T OPERATION OPERATION Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Blower housing might contain shredder blades and other sharp edges that can cause serious injuries if touched, even if engine is off and blades are not moving.
OPERATION PB-9010 H/T Fuel Diesel fuels and alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements are NOT approved for use in ECHO 2-stroke gasoline engines. Use of diesel or alternative fuels can cause performance problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, improper clutch engagement.
PB-9010 H/T ◆ ◆ OPERATION AVOID repeated or prolonged skin contact. AVOID inhaling oil mists or vapors. ECHO branded 2-stroke oils may be mixed at 50:1 ratio for application in all ECHO engines sold in the past regardless of ratio specified in those manuals. Handling Fuel Fuel is VERY flammable. Use extreme care when mixing, storing or handling, or serious personal injury will result. ◆ Use an approved fuel container. Mark fuel containers as containing 2-stroke mixture fuel. ◆ DO NOT smoke near fuel.
OPERATION PB-9010 H/T Mixing Instructions Stored fuel ages. Do not mix more fuel than you expect to use in 30 days, 90 days when a fuel stabilizer is added. 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of 2-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline. 4. Add remaining gasoline, close fuel container, and remix. Fuel to Oil Mix – 50:1 Ratio US Metric Gas Oil Gas Oil gal. fl.oz. L cc 1 2.
PB-9010 H/T OPERATION Starting Cold Engine PB-9010 H only: • Rotate spring loaded throttle arm downward to a comfortable operating position. PB-9010 H/T: • Recoil starter: Use short pulls - only 1/2- 2/3 of rope length for starting. Do not allow the rope to snap back in. Always hold the unit firmly. 1. Throttle Lever Move throttle lever (A) to IDLE position. 2. Rotate choke (B) to COLD START position. 3. A Choke PB-9010 H Purge Bulb Pump purge bulb (C) until fuel is visible.
OPERATION 4. PB-9010 H/T Recoil Starter Pull recoil starter handle (D) until engine fires, or a maximum of 5 pulls. B D C 5. If engine fires and remains running, pull throttle trigger (T model) or advance throttle lever (H model) to automatically return choke to run position, then proceed to engine warm up. If engine fires and dies, proceed to step 6. 6.
PB-9010 H/T OPERATION Starting Warm Engine The starting procedure is the same as Cold Start except DO NOT close the choke. 1. Throttle Lever Move throttle lever (A) to IDLE position. 2. A Purge Bulb Pump purge bulb (C) until fuel is visible. Pump bulb an additional 4 or 5 times. PB-9010 H A PB-9010T 3. Recoil Starter Pull recoil starter handle (D) and engine should start. Do not use choke (B). B Note: If engine does not start after 5 pulls, use cold start procedures.
OPERATION PB-9010 H/T Stopping Engine PB-9010 H 1. Move throttle lever (A) to IDLE position and allow engine to return to idle before shutting off engine. 2. A Throttle Lever PB-9010 H Throttle Lever Move throttle lever (A) to (STOP) position. PB-9010 T 1. Throttle Lever Release throttle trigger. Move Throttle Lever (A) forward to idle position and allow engine to return to idle before shutting off engine. 2.
PB-9010 H/T OPERATION Always wear safety glasses, hearing protection and a face filter mask or serious personal injury may result. Do not point the blower pipe in the direction of people or pets. Use reduced speed only when performing light-duty tasks or to comply with local noise regulations. Continuous low speed operation may allow fuel/oil residue to build-up on the piston and cause rapid build-up of carbon on the spark arrestor screen, resulting in overheating and engine damage.
OPERATION 4. PB-9010 H/T PB-9010 H A Set engine speed with throttle position lever (A). PB-9010 T PB-9010 H Control engine speed with throttle trigger (B), or for continuous use, set engine speed with throttle position lever (A). 5. Use lower speed to blow dry leaves from walks, patios and drives. Use rakes and brooms to loosen debris before blowing. 6. Additional speed may be necessary to clean grass and leaves from a lawn or flower bed. 7. 8.
PB-9010 H/T OPERATION For Operator Comfort in Cold Weather Operation: This product should not be used in temperatures below 15° F (-9° C) otherwise damage to the fuel lines may occur. 1. Remove clips from back cushion. Remove back cushion (A) from frame. A 2. Install cold weather insert (B) on frame over air intake. 3. Install back cushion (A) to frame over cold weather insert. Note: Blower performance may be reduced slightly.
OPERATION PB-9010 H/T Adjust harness 1. Pull straps (C) downward to adjust shoulder harness. 2. Adjust harness limiter strap (D) for comfortable operation.
PB-9010 H/T MAINTENANCE MAINTENANCE Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces.
MAINTENANCE PB-9010 H/T Maintenance Intervals COMPONENT/SYSTEM MAINTENANCE PROCEDURE SKILL LEVEL Daily or Before Use Air Filter Choke Shutter Inspect/Clean 1 Fuel System Inspect Cooling System Inspect/Clean 1 2 1 Recoil Starter Rope Inspect/Clean Screws/Nuts/Bolts Inspect/Tighten/Replace 1 1 Every Refuel Fuel System Inspect 1 1 Cooling System Inspect/Clean 2 3 Months Air Filter Fuel Filter Fuel Cap Gasket Spark Plug Muffler Spark Arrestor Cylinder Exhaust Port Replace 1 Inspect 1 1
PB-9010 H/T MAINTENANCE Air Filter Level 1. Parts Required: TUNE UP KIT. 1. Close choke (COLD START position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated dirt from air cleaner area. 2. Remove air filter cover, foam pre-filter, and air filter. Brush dirt from inside cover. Foam Pre-Filter: • Clean foam pre- filter (A) in water/detergent solution and rinse with clean water.
MAINTENANCE 1. Use a clean rag to remove loose dirt from around fuel cap and empty fuel tank. 2. Pull the fuel filter from the tank. PB-9010 H/T Do not damage fuel line while removing fuel filter from tank. 3. Remove the filter from the line and install the new filter. Note: Federal EPA regulations require all model year 2012 and later gasoline powered engines produced for sale in the United States to be equipped with a special low permeation fuel supply hose between the carburetor and fuel tank.
PB-9010 H/T MAINTENANCE 1. Remove spark plug and check for fouling, worn and rounded center electrode. 2. Clean the plug or replace with a new one. DO NOT sand blast to clean. Remaining sand will damage engine. 3. Adjust spark plug gap by bending outer electrode. 4. Tighten spark plug to 102-153 kgf • cm (86-133 in • lbf). X7501200700 © 08/20 ECHO Incorporated 0.65 mm (0.026 in.
MAINTENANCE PB-9010 H/T Cooling System Level 2. To maintain proper engine operating temperatures, cooling air must pass freely through the cylinder fin area. This flow of air carries combustion heat away from the engine. Overheating and engine seizure can occur when: • Air intakes are blocked, preventing cooling air from reaching the cylinder. • Dust and grass build up on the outside of the cylinder. This build up insulates the engine and prevents the heat from leaving.
PB-9010 H/T MAINTENANCE Clear Debris 1. Brush accumulated debris from intake grill and other cooling passages. Cleaning Cylinder Fins 1. Disconnect spark plug lead from spark plug. 2. Remove engine cover. 3. Clean cylinder fins (A) to allow cooling air to pass freely. 4. Install engine cover. 5. Connect spark plug lead. A A Exhaust System Spark Arrestor Screen Level 2. Parts Required: Spark Arrestor Screen Carbon deposits in muffler will cause a drop in engine output and overheating.
MAINTENANCE 1. Disconnect spark plug lead from spark plug. 2. Remove engine cover. 3. Remove spark arrestor screen (C) from muffler. Replace screen if plugged with carbon deposits. PB-9010 H/T Note: When cleaning carbon deposits, be careful not to damage the catalytic element inside muffler. 4. Install spark arrestor screen. 5. Install engine cover. 6. Connect spark plug lead. C Exhaust Port Cleaning Level 2. Parts Required: As needed: Muffler Gasket 1.
PB-9010 H/T 3. MAINTENANCE Use a wood or plastic scraping tool to clean deposits from cylinder exhaust port. Never use a metal tool to scrape carbon from the exhaust port. Do not scratch the cylinder or piston when cleaning the exhaust port. Do not allow carbon particles to enter the cylinder. 4. Inspect muffler gasket, and replace if damaged. 5. Install muffler gasket and muffler. 6. Tighten muffler mounting bolts (or nuts) to 110-150 kgf•cm (95-130 in•lbf). 7.
MAINTENANCE PB-9010 H/T If the engine is adjusted for operation above 1,100 feet (335 m) above sea level, the carburetor must be re-adjusted when operating the engine below 1,100 ft. (335 m) above sea level, otherwise severe engine damage may result. Level 2. Parts Required: None Note: Every unit is run at the factory and the carburetor is set in compliance with emission regulations. Carburetor adjustments, other than idle speed, must be performed by an authorized ECHO dealer.
PB-9010 H/T MAINTENANCE Throttle Cable Adjustment (PB-9010 T, EB910RT only) Level 1 If engine idle speed changes when blower pipe is moved, or engine will not reach full wide open throttle speed, adjust throttle cable. 1. Loosen handle adjustment knob (C) and tilt Tube Throttle handle forward to expose Adjustment Screw (D). D C D 2. Turn Adjustment Screw until Throttle Trigger free play is 4 - 6 mm (3/16-1/4 in.). 3.
TROUBLESHOOTING PB-9010 H/T TROUBLESHOOTING Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by grounding spark plug near cylinder plug hole, otherwise serious personal injury may result.
PB-9010 H/T STORAGE ENGINE PROBLEM TROUBLESHOOTING CHART Problem Check Status Air filter Air filter dirty Normal wear Fuel filter dirty Fuel filter Engine runs, but dies Fuel vent or Spark plug Engine does not accelerate properly Carburetor Fuel vent plugged Plug dirty or worn Improper adjustment Cooling system dirty or plugged Spark arrestor screen plugged Cooling system Spark arrestor screen Engine does not crank Cause N/A Contaminants or residue in fuel Contaminated fuel Remedy Clean o
STORAGE PB-9010 H/T 1. Store unit in a dry, dust free place, out of the reach of children. 2. Place the stop switch or lever in the “OFF” position. 3. Remove accumulation of grease, oil, dirt and debris from exterior of unit. 4. Perform all periodic lubrication and services that are required. 5. Tighten all the screws and nuts. 6. Drain fuel tank completely. Press purge bulb 6 -7 times to remove remaining fuel from carburetor then drain the tank again.
PB-9010 H/T SPECIFICATIONS SPECIFICATIONS MODEL PB-9010H Length (with pipes) Width (with pipes) PB-9010T 1564 mm (61.6 in. ) 630 mm (24.8 in.) Height (with pipes) 603 mm (23.7 in.) 544 mm (21.4 in.) Weight (full tank) (w th pipes) 13.2 kg (29.1 lb.) Engine Type 13.1 kg (28.8 lb.) Air cooled, two-stroke, single cylinder gasoline engine Bore 53 mm (2.1 in.) Stroke 36.2 mm (1.4 in.) Displacement 79.9 cc (4.
PRODUCT REGISTRATION PB-9010 H/T PRODUCT REGISTRATION Thank you for choosing ECHO Power Equipment Please go to http://www.echo-usa.com/Warranty/Register-Your-ECHO to register your new product on-line. It's FAST and EASY! NOTE: your information will never be sold or misused by ECHO, Incorporated. Registering your purchase enables us to contact you in the unlikely event of a service update or product recall, and verifies your ownership for warranty consideration.
PB-9010 H/T X7501200700 © 08/20 ECHO Incorporated PRODUCT REGISTRATION 51
(H)P53315001001 - P53315999999 (T)P53415001001 - P53415999999 ECHO INCORPORATED 400 Oakwood Road Lake Zurich, IL 60047 www.echo-usa.
