IMPORTANT SAFETY INSTRUCTIONS Care should be taken in mounting or dismounting the stationary exercise hike. Before mounting or dismounting move the pedal on the mounting or dismounting side to is lowest position and bring the machine to a complete stop. The manufacturer recommends to place the Echelon’ Connect bike in a space where you have two feet of clearance on all sides of the bile for safe mounting and dismounting of the exercise bike. The minimum dimensions are: 0.5m {19.
& IMPORTANT SAFETY INSTRUCTIONS (cont'd) Before using the Echelon” Connect, answer these questions: « Have you been sick recently? + Have you had prolonged dizziness recently? « Have you been out of breath for no reason recently? « Have you had chest pain recently? « De you currently have any injuries preventing vou from exercise? «Are you pregnant? = Do you have any conditions or reasons you should NOT exercise? + Are you over 35 years old and physically inactive? + Have you been told by a doctor that you
NEVER adjust the resistance of the flywheel or the position of the handlebars while in a standing position. NEVER use accessory attachments halt have not been recommended by the manufacturer. Using such attachments may cause Injury or damage to the bike and will affect the warranty of the bike, ALWAYS ensure that the Echelon” Connect Is wiped down after each use to keep it sanitary. Cleaning and user maintenance shall not be made by children without supervision.
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT 5.21 You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could cold the user's authority to operate the equipment. 151058) This equipment has been tested and found to comply with the limits for a {lass B digital device, pursuant to part 15 of the FCC tales. These limits are designed to provide reasonable protection against harmful interference in a residential Installation.
WARNING LABELS Rosemarie free Pinch Herder Russ ds Inconstant i Plain to Pizzazz gos wigs drs a |Buy Spin Pinch Warning Labels Te SEE en on Flywheel Cover, oh ee iis Doth Sides Een == She: BEE. iad Efe, PRK HAZARD rescue DE PAVEMENT br IRR RR SR HO FRIG) DE PELF CO.
BIKE SPECIFICATIONS Tablet Hurdle bars Tablet Mount Amn Durable Water Bottle Holders Holder Forebear Seal Adjustment Knob Forklift Handlebar Adjustment Knob Heat Height Adjustment Aver . Handlebar Thought Adjustment Aver Flywheel LED LED Light Strip Light Strip Lovey Park .
TABLET SPECIFICATIONS used HD Tiers AUK Us SE-a Theme Tablet Power/ Slap Push button once to put tablet io sleep mode. Hold button for menu to power off tablet, restart tablet, or take 8 screenshot.
INCLUDES Handlebar Height Adjustment Lever Handlebar Post Frame Resistance Knob Crank Arm Seat Pest Seat Height Adjustment Lever Fore / Aft Seat Adjustment Knob Front Packaging Fixer Tube Back Packaging Flier Tube . Tablet Front Fool . Handlebars . Tablet Mount Arm . Water Bottle Holder . Chandigarh Post . Back Foot Bem EN autobahns Dumbbell Holder Pedals Noway Adapter . Saddle (Seal) . Fore] Aft Handlebar Adjustment Knob . Handlebar Support Bracket {i . Decorative Cover (0) . Bolt {J} . Screws (H) .
Assembly should take place on 2 soft surface, such as carpet or a rug, or with the cardboard box opened fo protect the floor. Twe people are needed Tor assembly. Open the box and remove the bile parts and accessories. a. Carefully cut the tape holding the Styrofoam together and the bike parts and accessories in place. ¥b. Remove the seat, handlebars, rails, and other accessories from the top and sides of the Styrofoam. ¢. Remove hardware blister pack but do not pane sections until needed. d.
Remove the front packaging fair tubs. a, First Person: Raise front bike body to allow access to packaging hair tube. Bb. Second person: Remove bolts from front packaging fixer whe with the hex key {D} ©. Remove the fixer tube and bolts. Discard. Assemble the front fool. a, Gather front foot {with transport wheels) and (4) corresponding bolls and washers {I}. &. Ensure one washer Is placed on each boll ¢. First Person: Raise front bike body. d.
Remove the back packaging fixer tube. &. First Person: Raise back bike body to allow access to packaging Tiger tube, Bb. Second person: Remove bolts from back packaging fixer tube with the hex key {OD} ©. Remove the back packaging fixer tube and flywheel bolts. d. Use hex key (D} to remove flywheel lock bolt. Discard. Assemble the back foot, @. Gather back foot {no wheels} and {4} corresponding bolts and washers {fl #. Ensure one washer is placed on each bolt ©. First Person: Raise back bike body, d.
Place the saddle (seat). a. Place the saddle on the saddle bar b. Adjust the saddle left and right until centered with the nose fading the front of the bike, Secure the saddle (seat). a. Use small wrench (8) to tighten nuts on right underside of saddle. I. Repeat on the lef{ side. @. Ensure nuts are fully tightened, If not fully secured, the saddle may move.
Raise your saddle to full height. & Loosen the adjustment lever counterclockwise. Note: To reposition the angle of the handle on the adjustment lever without tightening or loosening, pull the handle out, reposition, and return, b. Grasp saddle and pull up until you see "MAX" on rail. ¢. Tighten adjustment lever clockwise. Attach the dumbbell holder. u. Gather dumbbell holder, screws [H), and hex key (D). B.
Prop handlebar post. a, Loosen handlebar adjustment lever by twisting counterclockwise. Do not fully remove, Bb. Undo twist te from even ©. Pull up on twist te until main wire Is visible, d. Grasp main wire. Do not allow wire to drop down Into handlebar post. Connect handlebar wire to handlebar post wire @, Gather handlebars and locate wire, Bb. First Person: Hold handlebars, ©. Second Person: Connect wires from handlebar to wires from handlebar post. 4.
Attach handlebar post. a. Place handlebars in handlebar post with top bar facing oul. B. Fully lower the handlebars. Attach placement straw, a. Gather bolt {J} and hex key (E) b. Finger tighten bolt {JL ©. Tighten bolt {J} with hex key (E]. do. Attach decorative cover {CL Hate: do not sip this step! Bolt {J} prevents handlebars from accidentally being removed from bike.
Attach tablet mount wires to bike, a, Pull out the wire from tablet mount arm, Bb. Pull out the wire from handlebar top bar ¢. Connect the wire from tablet mount am to the wire from handlebar top bar. Make sure connection is secures. d. Remove twist ties and discard, Attach tablet mount arm, @, Gather {2) bolts and washers (6), Bb. Ensure one washer is on each bolt, ©. Feed wire into tablet mount arm. 4. Slide tablet mount arm lento handlebar top bar. @. Finger tighten bolt {BG}, £.
Attach handlebars. a, Gather handlebar knob and handlebar support bracket {K). b. Put handlebar support bracket {i} onto handlebar knob post. ¢. First Person: Place handlebars, facing up, onto handlebar mount arm. d. Second Person: Place knob post info hole in handlebar mount arm and slide forward until resistance Is hit. a. Tighten handlebar adjustment knob clockwise, Attach water bottle holder. a. Gather water bottle holder and (2) screws H), &.
Prep bight pedal, a. Gather right pedal and both large and small wrenches, b. Both pedal and crank arm feature lefter “RS ¢. Remove right pedal nub with small wrench. Attach right pedal, a, Hold right pedal shaft up to hole In crank arm. Bb. Use small wrench to attach right pedal by muting dock wise until halfway screwed onto crank arm. Note: For pedal shaft, wrench should turn towards front of bike. €. Place pedal nut onto pedal shaft with white side facing bike. 4.
Prep left pedal. a. Gather loft pedal and both large and small wrenches. Bb. Both pedal and crank arm feature lecher “L° ©. Remove left pedal nut with small wrench, Attach loft pedal, a. Hold left pedal shaft up to hole in crank am. Bb. Use small wrench to attach loft pedal by turning counterclockwise until halfway screwed onto crank anm, Hate: For pedal shaft, wrench should fur towards front of bike, ©. Place pedal nut onto pedal shalt with white side facing bike.
Prop tablet. a. Gather tablet and Phillips screwdriver {D). b. Remove lower decorative cover by hooking thumbs underneath cover and pulling out + up. ¢. Remove upper decorative cover by hooking thumbs underneath cover and pulling out + up. Attach tablet. a. Remove ail 8) screws from tablet with Phillips screwdriver {DL Bb. First Person: Hold tablet so screw holes align with corresponding holes on tablet mount. «.
Finish tablet assembly. @. Grab DC cable from tablet holder tall and plug Into tablet, bi. Reattach top decorative cover. «. Pivot tablet up and reattach lower decorative cover, Note: ensure the lower decorative cover Is fully clipped In, Including the outer edges. Hove bike to final location. a. With two people, move bike to final location. if uneven, proceed to steps bo. &. Gather large wrench, ©. First Person: Lift back of bike so back feel are angled up. d.
Membership Activation leg to Unlock the Connect EX Bs Bike Fascistic ec Plug in bike. a. Gather power adapter and power plug cord, bi. Attach power plug cord to power adapter €. Plug power adapter into DC power port located al rear base of bike. Titivate Echelon Premier Membership to connect ip classes. To learn mare about the membership, visit echelon fit com/membership. &. Scan OR code below or visit memberechelonfit.com. br.
USING THE ECHELON EX-8 CONNECT BIKE Saddle + Handlebar Adjustment Before riding your EX-8, adjust your saddle and handlebars lo ensure proper form, 4. Adjust the saddle {seal} height. #. Loosen adjustment lever by twisting counterclockwise. bi. Raise or lower until the saddle is Sven with your hip bonds. ¢. Tighten adjustment lever clockwise unl! secure, Mote: To reposition angle of handle on adjustment lever without tightening or loosening, pull handle oul, reposition, and return. 2.
3. Adjust the handlebar height. #. Loosen the adjustment lever by twisting counterclockwise, I. False or lower until the handlebars are at least even with the saddle. You may want to raise higher depending on preference. Tighten the adjustment lever clockwise until secure, Hate: To reposition angle of handle on adjustment lever without tightening of loosening, pull handle out, reposition, and return. 4. Adjust handlebars forefather straightforwardness. a.
USING THE ECHELON EX-8 CONNECT BIKE (cont'd) Troubleshooting If the indicator light, located at the base of the handlebar rail, continues to blink the bike and tablet are not paired. indicator Light 1. Ensure the bike DU cable is fully inserted into the bike DC port located below the rear flywheel, 2. Ensure the tablet DC cable that comes from the tablet mount arm is fully inserted into the DC port at the base of the back of the tablet. 3. Rely pairing.
Connecting to the Echelon Fit App When using your Echelon EX-8 Connect Bike for the first time, you must pair the tablet (screen) to the bike via Bluetooth”, 4. Ensure your bike and tablet {screen} are both powered on. 3. Selects class. &. The power adapter plug with DC cable should be plugged Into the wall #, We recommend a Welcome Ride, but any class will work. and the base of the bike, Bb. Press play. Bb.
CARE + MAINTENANCE 1. Inspect the pedals of your bike before each ride for any looseness of deformation. Follow instructions from pages tighten, as needed. Doing this ensures your safety, the quality of your experience, and the overall ife of your bike. f any issues are found cease using the equipment immediately and contact customer service (833-937-2453), 2. if using eyeing shoes, check that the SPD cleats on your shoes are oriented straight to ensure proper clipping onto the pedal.
Weekly 1 Inspect all the assembled and per-assembled hardware to find If anything needs to be tightened or re secured.
CARE + MAINTENANCE (cont'd. Monthly 1. Assess the saddle and handlebar adjustments for wear and tear. fa replacement is needed contact customer service (833-937-2453). 2. Assess the quality of the drive belt every 5 § months by CAREFULLY removing the screws from the right side frame cover and using a flashlight io #assess the belt from the top down while pedaling with one hand, 3. Check nylon fool straps on toe cages for wear As Hooded 1.
Yearly 1. Assess the quality of the resistance encoder a. Remove the decorative tape surrounding the resistance knob, br. Use a small Phillips head screwdriver remove all {8} screws surrounding the knob and remove the knob. ©. Assess the motherboard for any dust, damage, of corrosion caused by sweat. Clean the area for dust and debris with compressed air, a, If a new resistance knob or resistance encoder is needed, contact customer service (833-837-2453) for replacement. 2.
CUSTOMER SERVICE 38 | CUSTOMER SERVICE Questions or Concerns Gur members are our priority! If you require assistance or have concerns, please contact our customer service team. %. (833) 937-2453 cs@echelonfitoom Submit a Request Warranty Information Your Echelon EX-8 Connect Bike comes with a testy parts and labor warranty. Should the need ares, all you need is a proof of purchase and our customer service team will be happy to assist.