HD Video Link Full HDMI Wireless Audio/Video Sender System VLHD30 Before using our product, please read this documents carefully.
User Guide CONTENTS 1. CONFORMITY OF USE 2. INTRODUCTION 3. SET CONTENTS 4. GENERAL SPECIFICATIONS 5. HARDWARE OVERVIEW 6. BEFORE YOU BEGIN 7. INSTALLING THE SYSTEM 8. QUICK INSTALLATION GUIDE 9. TECHNICAL DATA 10. Q&A 1. Conformity of Use For carefree and safe use of this product, please read this manual and safety information carefully and follow the instructions. The unit is registered as a device that does not cause or suffer from radio-frequency interference.
2. Introduction This wireless HD audio/video kit solution allows you to place your HD TV set or projector wherever you want, free of constraint or cables. Just connect your HD TV or projector to the Receiver with an HDMI cable, and connect your A/V equipment (Blu-ray players, HD set-up boxes, game consoles or HD media players and streamers) to the Transmitter. Almost every display with an HDMI input is compatible with this kit, please make sure the display supports HDCP when watching Blu-ray movies.
3. Set contents 1x 1x 2x 1x 2x 2x Transmitter Receiver Bracket IR Extension Cable HDMI Cable Power Adapter 4. General Specifications Supported Video Resolution Supported Audio Formats Communication system Modulation Transmission Max.
. Hardware Overviews Transmitter ① Receptor for the power Adapter 5V/2A, using power supply with different Voltage rating than the one included with the VLHD30 will cause damage and void warranty for these products. ② HDMI Input Connector Connect all devices with a good quality HDMI High Speed Cable to make sure The connection is in the best possible condition. ③ IR signal output interface Connect the IR extension cable and aim the IR head to the device which need to be control.
Receiver ① Receptor for the power Adapter 5V/2A, using power supply with different Voltage rating than the one included with the VLHD30 will cause damage and void warranty for these products. ② HDMI Output connector Connect all devices with a good quality HDMI High Speed Cable to make sure The connection is in the best possible condition. ③ Network Link LED status After the power is connected, the green LED in the front will show the communication status.
6. Before you begin: Wireless considerations The HDMI wireless kit let you access your video signal using a wireless connection from virtually anywhere within the operation range. Keep in mind, however, that the number, thickness and location of the wall and ceilings, or other objects that the wireless signal must pass through, may limit the range. Typically range depending on the type of material and background RF noise in your home and business.
7. Installing the system 1．Please install the Receiver with the included bracket, and put it properly beside the TV. ● when installing, put the Antenna Button on the front of the receiver in the upper position. ● Keep the Receiver area clear, too may objects will reduce the receivers signal quality. ● The Maximum distance of the Transmitter and Receiver is 30 meter (100 feet) line of sight. Walls and ceilings will reduce the signal range.
Note: Our product will only operate with 38K modulation remote controls.
8.
receiver transmitter 9. Technical Data Model name VLHD30 Operating Frequencies 5.1~5.9GHz Frequency stability ±4PPM Band with（Max.） 40MHz Transmission Max. Power ≥12dBm Receiver sensitive ≤-75dBm System Latency ≤1ms transmission/ receiver channel 4channel/ 1channel HD Video interface HDMI 1.3a HD Video Encryption HDCP 1.2 LOS(line of sight) ≦30M (100Feet) Input voltage 5VDC Operation current 2A±10% Operating Frequencies 5.1~5.
LED Status： LED Network Link (Transmitter) Video Link (Transmitter) Network Link (Receiver) Video Link (Receiver) status Green on Green off Green blinking Green on Green off Green on Green off Green blinking Green on Green off Working status Connection successful Connection failed Device defect Video connection successful Video connection failed Connection successful Connection failed Device defect Video connection successful Video connection failed 10.
* Failure 3: The distance between the transmitter and receiver are close, why 1 minute later the Network Link LED is still off? Answer：Please check the frequency between the transmitter and receiver is set. Please follow the frequency setting process to tune the frequency. * Failure 4: The Network Link LED is on in the transmitter and receiver，but the Video Link LED is off and the TV has no image? Answer: Please make sure the transmitter resolution is in the technical specification.
NOTES 31-5-2012 14 ebode VLHD30
DECLARATION OF CONFORMITY Hereby, ebode declares that this VLHD30 is in compliance with the essential requirements and other relevant provisions of the following Directives: 1) Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity 2) Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of the Member States
DECLARATION OF CONFORMITY TO R&TTE DIRECTIVE 1999/5/EC for the European Community, Switzerland, Norway, Iceland and Liechtenstein Product category: general consumer (category 3). English: This equipment is in compliance with the essential requirements and other relevant provisions of the European R&TTE Directive 1999/5/EC Deutsch [German]: Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.
Also available from ebode: TAKE10 Universal Remote Control The TAKE10 is an elegant universal remote that is able to control up to 10 A/V devices, including TV, DVD, VCR, Cable, X10 Home Automation products and more.
Also available from ebode: LightSpeaker The Next Bright Idea The unique ebode LightSpeakerTM cleverly combines low consumption LED lighting with wireless sound in one easy ‘plug and play’ system that can be hidden away in a lampshade or light fitting. !nstall it into any room in just a few minutes without tools or extra wiring! LightSpeakerTM can be mounted into many different light fixtures including pendants fittings, table and floor lamps.
Also available from ebode: Hide your A/V gear Place your A/V equipment inside your TV cabinet and out-of-sight! Use ebode’s InfraRed products to control your equipment with your existing remote control. Place the table top mouse Receiver on top of your TV cabinet. Stick the Mini Receiver right next to or under your TV. Mount the Flush- Mount Receiver in your TV cabinet.
www.ebodeelectronics.
