Powerware ® BladeUPS ® Extended Battery Module (EBM) User's Guide
Special Symbols The following are examples of symbols used on the UPS or accessories to alert you to important information: RISK OF ELECTRIC SHOCK - Indicates that a risk of electric shock is present and the associated warning should be observed. CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's manual for additional information, such as important operating and maintenance instructions. This symbol indicates that you should not discard the UPS or the UPS batteries in the trash.
Table of Contents 1 2 3 4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Inspecting the Equipment . . . . . . . . . . . . . . . . .
TABLE OF CONTENTS ii EATON Powerware® BladeUPS® EBM User's Guide S 164201650 Rev 2 www.powerware.
Chapter 1 Introduction The Extended Battery Module (EBM) can be added to the Powerware® BladeUPS® uninterruptible power system (UPS) to extend the available battery time (see Table 1). Up to four EBMs can be installed with the Powerware BladeUPS. Table 1. Battery Runtimes (in Minutes) Model UPS Internal Batteries +1 EBM +2 EBMs +3 EBMs +4 EBMs BladeUPS 12 4.8 12 20 27 34 BladeUPS 12i 4.
INTRODUCTION Sikkerhedsanvisninger VIGTIGE SIKKERHEDSANVISNINGER GEM DISSE ANVISNINGER Denne manual indeholder vigtige instruktioner, som skal følges under installation og betjening af EBM-enheden. Læs venligst alle instruktioner inden betjening af udstyret og gem denne manual mhp. fremtidige opslag. ADVARSEL! Denne UPS indeholder sin egen energikilde (batterier). Udgangsstikkene kan endog være strømførende, når UPS'en ikke er koblet til en vekselstrømsforsyning.
INTRODUCTION Belangrijke Veiligheidsinstructies BELANGRIJKE VEILIGHEIDSINSTRUCTIES BEWAAR DEZE INSTRUCTIES Deze handleiding bevat belangrijke instructies die u dient te volgen tijdens de installatie en het gebruik van EBM. Lees alle instructies voordat u de apparatuur in bedrijf neemt en bewaar deze handleiding als naslagwerk. WAARSCHUWING Deze UPS bevat een eigen energiebron (batterijen). De uitgangscontactdoos kan onder spanning staan, zelfs wanneer de UPS niet is aangesloten op de netspanning.
INTRODUCTION Tarkeita Turvaohjeita TÄRKEITÄ TURVAOHJEITA - SUOMI SÄILYTÄ NÄMÄ OHJEET Tämä käyttöohje sisältää tärkeitä ohjeita, joita on noudatettava EBM-yksikön asennuksen ja käytön yhteydessä. Lue kaikki ohjeet ennen laitteiston käyttöä ja säilytä ohje myöhempää tarvetta varten. VAROITUS Tässä UPS-virtalähteessä on oma energianlähde (akut). Lähtövastakkeissa voi olla jännite, vaikka UPS-virtalähdettä ei ole kytketty verkkovirtaan.
INTRODUCTION Consignes de Sécurité CONSIGNES DE SÉCURITÉ IMPORTANTES CONSERVER CES INSTRUCTIONS Ce manuel contient des instructions importantes que vous êtes invité à suivre lors de toute procédure d'installation et de fonctionnement de l'EBM. Veuillez consulter entièrement ces instructions avant de faire fonctionner l'équipement et conserver ce manuel afin de pouvoir vous y reporter ultérieurement. AVERTISSEMENT! Cette onduleur possède sa propre source d'alimentation (batteries).
INTRODUCTION Sicherheitswarnungen WICHTIGE SICHERHEITSANWEISUNGEN AUFBEWAREN Dieses Handbuch enthält wichtige Hinweise, welche Sie bei der Installation und Wartung des EBM beachten sollten. Bitte lesen Sie alle Anweisungen des Handbuches bevor sie mit dem Gerät arbeiten. Bewaren Sie das Handbuch zum Nachlesen auf. ACHTUNG Dieses UPS (Unterbrechungsfreies Stromversorgungssystem - USV) enthält eine eigene Energiequelle (Batterien).
INTRODUCTION Avvisi di Sicurezza IMPORTANTI ISTRUZIONI DI SICUREZZA CONSERVARE QUESTE ISTRUZIONI Il presente manuale contiene importanti istruzioni da seguire durante l'installazione e il funzionamento di EBM. Leggere integralmente le istruzioni prima di utilizzare l'apparecchiatura e conservare il presente manuale per futuro riferimento. AVVERTENZA L'UPS contiene la propria fonte di energia (batterie).
INTRODUCTION Viktig Sikkerhetsinformasion VIKTIGE SIKKERHETSINSTRUKSJONER GJEM DISSE INSTRUKSJONENE Denne håndboken inneholder viktige instruksjoner som du bør overholde ved montering og bruk av EBM. Les alle instruksjoner før utstyret tas i bruk, og gjem håndboken til fremtidig referanse. FARLIG UPS-enheten inneholder sin egen energikilde (batterier). Utgangsstikkene kan være strømførende selv når UPS-enheten ikke er koblet til et strømuttak.
INTRODUCTION Regulamentos de Segurança INSTRUÇÕES DE SEGURANÇA IMPORTANTES GUARDE ESTAS INSTRUÇÕES Este manual contém instruções importantes que devem ser seguidas durante a instalação e operação da EBM (Produção de energia elétrica por indução magnética). Leia todas as instruções antes de operar o equipamento e guarde este manual para consultá-lo futuramente. ADVERTÊNCIA Este no-break possui sua própria fonte de energia (baterias).
INTRODUCTION Предупреждения по мерам безопасности ВАЖНЫЕ УКАЗАНИЯ ПО МЕРАМ БЕЗОПАСНОСТИ СОХРАНИТЕ ЭТИ УКАЗАНИЯ В данном руководстве содержатся важные инструкции по установке и обслуживанию внешнего батарейного модуля или устройства распределения электропитания. Перед работой с оборудованием прочтите все инструкции. Сохраните данное руководство для дальнейшего использования. ПРЕДУПРЕЖДЕНИЕ В данном ИБП установлены собственные источники энергии (батареи).
INTRODUCTION Advertencias de Seguridad INSTRUCCIONES DE SEGURIDAD IMPORTANTES GUARDE ESTAS INSTRUCCIONES Este manual contiene instrucciones importantes que debe seguir durante la instalación y el funcionamiento del EBM. Por favor, lea todas las instrucciones antes de poner en funcionamiento el equipo y guarde este manual para referencia en el futuro. ADVERTENCIA Este SIE contiene su propia fuente de energía (baterías).
INTRODUCTION Säkerhetsföreskrifter VIKTIGA SÄKERHETSFÖRESKRIFTER SPARA DESSA FÖRESKRIFTER Den här anvisningen innehåller viktiga instruktioner som du ska följa under installation och användning av EBM. Läs alla instruktioner innan du använder utrustningen och spara den här anvisningen för framtida referens. VARNING Den här UPS-enheten innehåller sin egen energikälla (batterier). Uttagen kan vara spänningsförande även då UPS-enheten inte är ansluten till spänningsnätet.
Chapter 2 Installation NOTE If you are installing the UPS and the Extended Battery Module (EBM) together, follow the installation instructions in the UPS user's guide. This section explains: S Equipment inspection S Extended Battery Module (EBM) setup and installation Inspecting the Equipment If any equipment has been damaged during shipment, keep the shipping cartons and packing materials for the carrier or place of purchase and file a claim for shipping damage.
INSTALLATION EBM Setup The Powerware BladeUPS EBM comes with all hardware required for installation in a standard EIA or JIS seismic rack-mount configuration with square and round mounting holes. The rail assemblies adjust to mount in 48-cm (19-inch) racks with front to rear rail distances from 61 to 76 cm (24 to 30 inches) deep.
INSTALLATION Rack Setup for the EBM CAUTION The EBM is heavy [77 kg (170 lb)]. A minimum of two people are required to remove the EBM from its carton. NOTE Mounting rails are required for each individual cabinet. To install the EBM rail kit: 1. Loosen the assembly wing nuts on both rail assemblies and adjust the rail size for the depth of your rack (see Figure 1). Assembly Wing Nuts Front Rail Assembly Rear Figure 1. Adjusting the Rail Depth 2.
INSTALLATION Position 15 Second Rail Position 10 Position 6 First Rail Position 1 Figure 2. Front Rail Screw Positions for the EBM 3. Secure the rail to the front of the rack with two hex-head screws (see Figure 3). Front Rail Hex-Head Screws Figure 3. Securing the Front Rail 16 EATON Powerware® BladeUPS® EBM User's Guide S 164201650 Rev 2 www.powerware.
INSTALLATION 4. Using two clip nuts and two hex-head screws, attach the rail to the rear of the rack (see Figure 4 and Figure 5). The bottom rail uses positions 2 and 4 for the rear hex-head screws. If you are installing additional rails, place the next rail 7 holes above the last installed screw. Position 13 Second Rail Position 11 Position 4 First Rail Position 2 Figure 4. Rear Rail Screw Positions for the EBM Clip Nuts Figure 5.
INSTALLATION 5. Repeat Steps 3 and 4 for the other rail. 6. Tighten the assembly wing nuts on both rail assemblies. CAUTION The EBM is heavy [77 kg (170 lb)]. A minimum of two people are required to move the EBM. 7. Place the EBM on a flat, stable surface with the front of the EBM facing toward you. 8. If the mounting brackets are not already installed, align the two mounting brackets with the screw holes on the side of the EBM and secure with the supplied 6-32 flat-head screws (see Figure 6). 9.
INSTALLATION 11. Secure the front of the EBM to the rack using two hex-head screws in each mounting bracket as shown in Figure 7. Hex-Head Screws Figure 7. Securing the EBM Mounting Brackets 12. Attach the rear hold-down brackets to the rail and slide the brackets into the slots on the EBM rear panel (see Figure 8). Rear Hold-Down Bracket Figure 8. Securing the Back of the EBM EATON Powerware® BladeUPS® EBM User's Guide S 164201650 Rev 2 www.powerware.
INSTALLATION 13. Verify that the brackets are seated firmly, then tighten the wing nuts on the rear hold-down brackets. The EBM is now secured in the rack. 14. If installing additional EBMs, repeat Steps 7 through 13 for each cabinet. 15. Continue to the following section “EBM Installation.” EBM Installation CAUTION A small amount of arcing may occur when connecting an EBM to the UPS. This is normal and will not harm personnel. Insert the EBM cable into the UPS battery connector quickly and firmly.
INSTALLATION Battery Breaker UPS Battery Connector EBM Cable Battery Breakers EBM Battery Connectors Figure 9. Typical EBM Installation EATON Powerware® BladeUPS® EBM User's Guide S 164201650 Rev 2 www.powerware.
INSTALLATION 22 EATON Powerware® BladeUPS® EBM User's Guide S 164201650 Rev 2 www.powerware.
Chapter 3 Maintenance This section explains how to S Care for the UPS and batteries S Replace the Extended Battery Modules (EBMs) S Recycle used batteries or UPS UPS and Battery Care For the best preventive maintenance, keep the area around the UPS clean and dust‐free. If the atmosphere is very dusty, clean the outside of the system with a vacuum cleaner. For full battery life, keep the UPS at an ambient temperature of 25°C (77°F). NOTE The batteries in the UPS are rated for a 3–5 year service life.
MAINTENANCE How to Replace EBMs NOTE DO NOT DISCONNECT the batteries while the UPS is in Battery mode. Batteries can be replaced easily without turning the UPS off or disconnecting the load. If you prefer to remove input power to change the batteries, see “Individual UPS Shutdown” in the UPS user's guide. Consider all warnings, cautions, and notes before replacing batteries. WARNING S Servicing should be performed by qualified service personnel knowledgeable of batteries and required precautions.
MAINTENANCE CAUTION The EBM is heavy [77 kg (170 lb)]. A minimum of two people are required to lift the cabinet into the rack. To replace the EBMs: 1. Switch all battery circuit breakers to the OFF (O) position (see Figure 9 on page 21). 2. Unplug the EBM cable from the UPS. If additional EBMs are installed, unplug the EBM cable from the battery connector on each EBM. 3. If not already installed, install the supplied mounting brackets on the new EBM. 4. Replace the EBM.
MAINTENANCE Recycling the Used Battery or UPS Contact your local recycling or hazardous waste center for information on proper disposal of the used battery or UPS. WARNING S Do not dispose of the battery or batteries in a fire. Batteries may explode. Proper disposal of batteries is required. Refer to your local codes for disposal requirements. S Do not open or mutilate the battery or batteries. Released electrolyte is harmful to the skin and eyes. It may be toxic.
Chapter 4 Service and Support If you have any questions or problems with the UPS, call your Local Distributor or the Help Desk at one of the following telephone numbers and ask for a UPS technical representative.
*1642016502* 164201650 2
