User & Installation Manual IM02601001E Rev.
Copyright © 2011 by Eaton Corporation. All rights reserved. Eaton, Power Xpert, PowerChain Management, Powerware, and X-Slot are registered trademarks of Eaton Corporation or its subsidiaries and affiliates. Microsoft and Windows are registered trademarks of Microsoft Corporation. Modbus is a registered trademark of Schneider Electric.
Product Registration PLEASE REGISTER YOUR PRODUCT By registering your product you’re registering for the warranty in addition to receiving important update information. You can register your product in one of two ways: 1. Go online to: www.eaton.com/powerxpert and click on Power Xpert Product Registration to register your product. 2. Fill out the product registration information below and fax this page to 919-431-6240.
Table of Contents 1 Introduction..............................................................................................................................................................................1-1 About This Manual......................................................................................................................................................................1-1 Warranty and Liability Information.................................................................................
Network Communications with the Power Xpert® 2000 Series (-5)......................................................................................... 7-11 Using the PXM 2000 Gateway Card........................................................................................................................................7-12 8 Introduction to Web Server Pages.........................................................................................................................................
Introduction 1 INTRODUCTION About This Manual This document is the user manual for the installation, operation, and maintenance of the Eaton Power Xpert® Meter 2000 Series. It is intended for authorized and qualified personnel who use the PXM 2250/2260/2270/2280/2290 meters. Please refer to the specific WARNINGS and CAUTIONS in this section before proceeding.
Introduction Safety Precautions All safety codes, safety standards, and/or regulations must be strictly observed in the installation, operation, and maintenance of this device. WARNINGS refer to instructions that, if not followed, can result in death or injury. CAUTIONS refer to instructions that, if not followed, can result in equipment damage. WARNINGS SHOCK HAZARDS: IMPROPER INSTALLATION CAN CAUSE DEATH, INJURY, AND/OR EQUIPMENT DAMAGE. Follow all Warnings and Cautions.
Overview and Specifications 2 OVERVIEW AND SPECIFICATIONS Power Xpert Meter 2000 Series Overview The PXM 2250/2260/2270/2280/2290 is a multifunction power and energy meter designed to be used in electrical substations, panel boards, and as a primary revenue meter, due to its high performance measurement capability.
Overview and Specifications Voltage and Current Inputs Universal Voltage Inputs Voltage Inputs allow measurement up to 576VAC (Phase to Reference) and 721VAC (Phase to Phase). This insures proper meter safety when wiring directly to high voltage systems. One unit will perform to specification on 69 Volt, 120 Volt, 230 Volt, 277 Volt, and 347 Volt power systems. NOTE: Higher voltages require the use of potential transformers (PTs).
Overview and Specifications Ordering Information PXM -2260 -M - A - 6 - 5 - 1 - 1 - 5 1 2 3 4 5 6 7 1. Model: 2250 = Power Meter 2260 = Power Quality Meter 2270 = Power Quality Plus Meter 2280 = Power Quality Plus with up to 64 samples/cycle waveform recording meter 2290 = Power Quality Plus with up to 512 samples/cycle waveform recording meter 2. Meter Type M = Meter (with integral display) T = Transducer Only (no display) 3. Frequency: 5 = 50 Hz System 6 = 60 Hz System 4.
Overview and Specifications Measured Values The PXM 2000 Series provides the following measured values as Average, Maximum, Minimum and Actual values PXM 2000 Series Measured Values Parameter Min Max Avg mTotalVARh X mVAtotal X X X mVarC X X X mFreq X X X mVcnPerTHD X X X mVAB X X X mWtotal X X X mACIN X X X mNetEnergy X mLaggingVARh X mDemandNetWatts X mACVavgLL3Sigma mPFapparentA X X X X mDemandNetVARs X X mWB X X X mPosSeqV X X X X mDemandLeadi
Overview and Specifications Parameter Min Max Avg mVanPerTHD X X X mIntDemandForwardWatts mNegSeqV X X X X mACIavg X X X mACIA X X X mACVAB X X X X X mReverseEnergy X X mDemandIa X mVAA X X X mACVBN X X X mVbnPerTHD X X X mIntDemandLaggingVARs X X X X X X mACVCA X X X mVarA X X X mIntDemandReverseWatts mWA X X X X mNetVARh X X mDemandIn X X mDemandSumVARs X X mIntDemandSumWatts X X mDemandVAs X X mForwardEnergy X mPFapparentC X
Overview and Specifications Utility Peak Demand The PXM 2000 Series provides user-configured Fixed Window or Sliding Window Demand modes. This feature enables you to set up a customized Demand profile. Fixed Window Demand mode records the average demand for time intervals that you define (usually 5, 15 or 30 minutes). Sliding Window Demand mode functions like multiple, overlapping Fixed Window Demands. You define the subintervals at which an average of demand is calculated.
Overview and Specifications KYZ/RS485 Port Specifications RS485 Transceiver; meets or exceeds EIA/TIA-485 Standard: Type: Two-wire, half duplex Min. Input Impedance: 96kΩ Max. Output Current: ±60mA Wh Pulse KYZ output contacts (and infrared LED light pulses through face plate): (See Chapter 6 for Kh values.
Overview and Specifications Isolation All Inputs and Outputs are galvanically isolated to 2500 Vac Environmental Rating Storage: (-20 to +70)0 C Operating: (-20 to +70)0 C Humidity: to 95% RH Non-condensing Faceplate Rating: NEMA12 (Water Resistant), Mounting Gasket Included Measurement Methods Voltage, Current: Power: True RMS Sampling at over 400 Samples per Cycle on All Channels Update Rate Watts, VAR and VA: Every 6 cycles (e.g., 100 ms @ 60 Hz) All other parameters: Every 60 cycles (e.
Overview and Specifications Compliance • • • • • • UL Listing: USL/CNL E185559 CE (EN61326-1, FCC Part 15, Subpart B, Class A) IEC 687 (0.2% Accuracy) ANSI C12.20 (0.2% Accuracy) ANSI C62.41 (Burst) IEC 1000-4-2 - ESD Accuracy (See full Range specifications earlier in this chapter.) For 23o C, 3 Phase balanced Wye or Delta load, at 50 or 60 Hz (as per order), 5A (Class 10) nominal unit: Parameter Accuracy Input Range1 Accuracy Voltage L-N [V] 0.1% of reading (69 to 480)V Voltage L-L [V] 0.
Overview and Specifications 2-10 IM02601001E www.eaton.
Mechanical Installation 3 MECHANICAL INSTALLATION Introduction The PXM 2000 Series can be installed using a standard ANSI C39.1 (4” Round) or an IEC 92mm DIN (Square) form. In new installations, simply use DIN or ANSI punches. For existing panels, pull out old analog meters and replace them with the PXM Series meter. The various models use the same installation. See Chapter 4 for wiring diagrams.
Mechanical Installation 100 Act Fig. 3.4: Meter Back Figure 3.5: ANSI Mounting Panel Cutout Figure 3.6: DIN Mounting Cutout 3-2 IM02601001E www.eaton.
Mechanical Installation ANSI Installation Steps NEMA 12 Mounting Gasket Threaded Rods Lock Washer and Nut Figure 3.7: ANSI Mounting Procedure 1. 2. 3. 4. Insert 4 threaded rods by hand into the back of meter. Twist until secure. Slide NEMA 12 Mounting Gasket onto back of meter with rods in place. Slide meter with Mounting Gasket into panel. Secure from back of panel with lock washer and nut on each threaded rod. Use a small wrench to tighten.
Mechanical Installation DIN Installation Steps DIN Mounting Bracket (order separately as part # IQ250-DIN) Top Mounting Bracket Groove Bottom Mounting Bracket Groove #8 Screw PXM Series Meter with NEMA 12 Mounting Gasket Remove (unscrew) ANSI Studs for DIN Installation Figure 3.8: DIN Mounting Procedure 1. Slide meter with NEMA 12 Mounting Gasket into panel. (Remove ANSI Studs, if in place.) 2.
Mechanical Installation PXM 2000 Series Transducer Installation The PXM 2000 Series Transducer model is installed using DIN Rail Mounting. Specs for DIN Rail Mounting: DIN Rail (Slotted) Dimensions: International Standards DIN 46277/3 0.297244” x 1.377953” x 3” (inches) 7.55mm x 35mm x 76.2mm (millimeters) Figure 3.9: DIN Rail Mounting Procedure Release Clip 1. Slide top groove of meter onto the DIN Rail. 2. Press gently until the meter clicks into place.
Mechanical Installation 3-6 IM02601001E www.eaton.
Electrical Installation 4 ELECTRICAL INSTALLATION Considerations When Installing Meters Installation of the PXM 2000 Series must be performed only by qualified personnel who follow standard safety precautions during all procedures. Those personnel should have appropriate training and experience with high voltage devices. Appropriate safety gloves, safety glasses and protective clothing is recommended.
Electrical Installation CT Leads Terminated to Meter The PXM 2000 Series is designed to have Current Inputs wired in one of three ways. Diagram 4.1 shows the most typical connection where CT Leads are terminated to the meter at the Current Gills. This connection uses NickelPlated Brass Studs (Current Gills) with screws at each end. This connection allows the CT wires to be terminated using either an “O” or a “U” lug. Tighten the screws with a #2 Phillips screwdriver.
Electrical Installation CT Leads Pass Through (No Meter Termination) The second method allows the CT wires to pass through the CT Inputs without terminating at the meter. In this case, remove the Current Gills and place the CT wire directly through the CT opening. The opening will accomodate up to 0.177” / 4.5mm maximum diameter CT wire. CT Wire passing through meter Current Gills removed Figure 4.2: Pass-Through Wire Electrical Connection www.eaton.
Electrical Installation Quick Connect Crimp-on Terminations For Quick Termination or for Portable Applications, a 0.25” Quick Connect Crimp-on Connectors can also be used. Quick Connect Crimp-on Terminations Figure 4.3: Quick Connect Electrical Connection 4-4 IM02601001E www.eaton.
Electrical Installation Voltage and Power Supply Connections Voltage Inputs are connected to the back of the unit via a optional wire connectors. The connectors accomodate AWG# 12 -26/ (0.129 - 3.31)mm2. RS485 and KYZ Pulse Output CAUTION! Do not apply input or supply voltage to these Power Supply Inputs Voltage Inputs Figure 4.4: Voltage Connection Ground Connections The meter’s Ground Terminals should be connected directly to the installation’s protective earth ground. Use AWG# 12/2.
Electrical Installation Electrical Connection Diagrams The following pages contain electrical connection diagrams for the PXM 2000 Series. Choose the diagram that best suits your application. Be sure to maintain the CT polarity when wiring. The diagrams are presented in the following order: 1. Three Phase, Four-Wire System Wye/Delta with Direct Voltage, 3 Element a. Example of Dual Phase Hookup b. Example of Single Phase Hookup 2. Three Phase, Four-Wire System Wye with Direct Voltage, 2.
Electrical Installation 1. Service: WYE/Delta, 4-Wire with No PTs, 3 CTs Select: “ 3 EL WYE ” (3 Element Wye) from the Meter’s Front Panel Display. (See Chapter 6.) www.eaton.
Electrical Installation 1a. Example of Dual Phase Hookup Select: “ 3 EL WYE ” (3 Element Wye) from the Meter’s Front Panel Display. (See Chapter 6.
Electrical Installation 1b. Example of Single Phase Hookup Select: “ 3 EL WYE ” (3 Element Wye) from the Meter’s Front Panel Display. (See Chapter 6.) www.eaton.
Electrical Installation 2. Service: 2.5 Element WYE, 4-Wire with No PTs, 3 CTs This configuration is not recommended. In this configuration the B phase voltage is not measured to save the cost of a B Phase voltage transformer. A balanced 3 phase voltage is assumed to estimate B phase voltage for the purpose of 3 phase power and energy estimation (does not comply with Blondel’s theory). 2.5 element Wye configuration cannot detect problems with B phase voltage.
Electrical Installation 3. Service: WYE/Delta, 4-Wire with 3 PTs, 3 CTs Select: “ 3 EL WYE ” (3 Element Wye) from the Meter’s Front Panel Display. (See Chapter 6.) www.eaton.
Electrical Installation 4. Service: 2.5 Element WYE, 4-Wire with 2 PTs, 3 CTs This configuration is not recommended. In this configuration the B phase voltage is not measured to save the cost of a B Phase voltage transformer. A balanced 3 phase voltage is assumed to estimate B phase voltage for the purpose of 3 phase power and energy estimation (does not comply with Blondel’s theory). 2.5 element Wye configuration cannot detect problems with B phase voltage.
Electrical Installation 5. Service: Delta, 3-Wire with No PTs, 2 CTs Select: “ 2 Ct dEL ” (2 CT Delta) from the Meter’s Front Panel Display. (See Chapter 6.) www.eaton.
Electrical Installation 6. Service: Delta, 3-Wire with 2 PTs, 2 CTs Select: “ 2 Ct dEL ” (2 CT Delta) from the Meter’s Front Panel Display. (See Chapter 6.) 4-14 Not connected to meter IM02601001E www.eaton.
Electrical Installation 7. Service: Delta, 3-Wire with 2 PTs, 3 CTs Select: “ 2 Ct dEL ” (2 CT Delta) from the Meter’s Front Panel Display. (See Chapter 6.) Not connected to meter NOTE: The third CT for hookup is optional and is for Current Measurement only. www.eaton.
Electrical Installation 8. Service: Current Only Measurement (Three Phase) * Select: “ 3 EL WYE ” (3 Element Wye) from the Meter’s Front Panel Display. (See Chapter 6.) * For improved accuracy, this connection is recommended, but not required. 4-16 IM02601001E www.eaton.
Electrical Installation 9. Service: Current Only Measurement (Dual Phase) * Select: “ 3 EL WYE ” (3 Element Wye) from the Meter’s Front Panel Display. (See Chapter 6.) * For improved accuracy, this connection is recommended, but not required. www.eaton.
Electrical Installation 10. Service: Current Only Measurement (Single Phase) * Select: “ 3 EL WYE ” (3 Element Wye) from the Meter’s Front Panel Display. (See Chapter 6.) * For improved accuracy, this connection is recommended, but not required. 4-18 IM02601001E www.eaton.
Serial Communication Installation 5 SERIAL COMMUNICATION INSTALLATION PXM 2000 Series Communication The PXM 2000 Series provides RS485 communication speaking Modbus ASCII, Modbus RTU, and DNP 3.0 protocols. RS485 / KYZ Output (Com 2) Com 2 provides a combination RS485 and an Energy Pulse Output (KYZ pulse). See Chapter 2 for the KYZ Output Specifications; see Chapter 6 for Pulse Constants. Figure 5.
Serial Communication Installation Figure 5.2 shows the detail of a 2-wire RS485 connection. PXM 2000 Series Connection Figure 5.2: 2-wire RS485 Connection NOTES: For All RS485 Connections: • Use a shielded twisted pair cable 22 AWG (0.33 mm2) or thicker, and ground the shield, preferably at one location only. • Establish point-to-point configurations for each device on a RS485 bus: connect (+) terminals to (+) terminals; connect (-) terminals to (-) terminals.
Serial Communication Installation Slave device 1 SH A(+) B(-) Long stub results “T” connection that can cause interference problem! Master device Last Slave device N RT RT Slave device 2 SH A(+) B(-) SH A(+) B(-) Twisted pair, shielded (SH) cable SH A(+) B(-) Twisted pair, shielded (SH) cable Twisted pair, shielded (SH) cable Earth Connection, preferably at single location Twisted pair, shielded (SH) cable Twisted pair, shielded (SH) cable Slave device 1 Slave device 2 SH A(+) B(-) B(-) A(+
Serial Communication Installation PXM 2000 Series Transducer Communication Information The PXM 2000 Series Transducer does not include a display or buttons on the front face of the meter. Programming and communication utilize the RS485 connection on the back face of the meter shown in section 5.1.2. Once a connection is established, Eaton Meter Configuration Software can be used to program the meter and communicate to slave devices.
Using the PXM 2000 Series 6 USING THE PXM 2000 SERIES Introduction You can use the Elements and Buttons on the meter’s face to view meter readings, reset and/or configure the PXM 2000 Series, and perform related functions. The following sections explain the Elements and Buttons and detail their use.
Using the PXM 2000 Series Using the Front Panel You can access four modes using the meter’s front panel buttons: • Operating Mode (Default) • Reset Mode • Configuration Mode • Information Mode. Information Mode displays a sequence of screens that show model information, such as Frequency and Amps. Use the Menu, Enter, Down and Right buttons to navigate through each mode and its related screens. NOTES: • Appendix A contains the complete Navigation Map for the front panel display modes and their screens.
Using the PXM 2000 Series Using the Main Menu 1. Press the Menu button. The Main Menu screen appears. • The Reset: Demand mode (rStd) appears in the A window. Use the Down button to scroll, causing the Reset: Energy (rStE), Configuration (CFG), Operating (OPr), and Information (InFo) modes to move to the A window. • The mode that is currently flashing in the A window is the “Active” mode, which means it is the mode that can be configured. For example: Press Down Twice- CFG moves to A window.
Using the PXM 2000 Series Entering a Password If Password Protection has been enabled from the web pages for Reset and/or Configuration (see Chapter 8 for information), a screen appears requesting a Password when you try to reset the meter and/or configure settings through the front panel. • PASS appears in the A window and 4 dashes appear in the B window. The leftmost dash is flashing. 1. Press the Down button to scroll numbers from 0 to 9 for the flashing dash.
Using the PXM 2000 Series Using Configuration Mode Configuration Mode follows Reset: Energy on the Main Menu. To access Configuration Mode: 1. Press the Menu button while the meter is auto-scrolling parameters. 2. Press the Down button until the Configuration Mode option (CFG) is in the A window. 3. Press the Enter button. The Configuration Parameters screen appears. 4. Press the Down button to scroll through the configuration parameters: Scroll (SCrL), CT, PT, Connection (Cnct) and Port.
Using the PXM 2000 Series Configuring the Scroll Feature When in Auto Scroll mode, the meter performs a scrolling display, showing each parameter for 7 seconds, with a 1 second pause between parameters. The parameters that the meter displays are determined by the following conditions: • They have been selected through software. (Refer to Chapter 8 for instructions.) • Whether your meter model is a PXM 2250, 2260, 2270, 2280 or 2290. To enable or disable Auto-scrolling: 1.
Using the PXM 2000 Series Configuring CT Setting The CT Setting has three parts: Ct-n (numerator), Ct-d (denominator), and Ct-S (scaling). 1. Press the Enter button when Ct is in the A window. The Ct-n screen appears. You can either: • Change the value for the CT numerator. • Access one of the other CT screens by pressing the Enter button: press Enter once to access the Ct-d screen, twice to access the Ct-S screen.
Using the PXM 2000 Series Configuring PT Setting The PT Setting has three parts: Pt-n (numerator), Pt-d (denominator), and Pt-S (scaling). 1. Press the Enter button when Pt is in the A window. The PT-n screen appears. You can either: • Change the value for the PT numerator. • Access one of the other PT screens by pressing the Enter button: press Enter once to access the Pt-d screen, twice to access the Pt-S screen. a.
Using the PXM 2000 Series Configuring Connection Setting 1. Press the Enter button when Cnct is in the A window. The Cnct screen appears. 2. Press the Right button or Down button to select a configuration. The choices are: • 3 Element Wye (3 EL WYE) • 2.5 Element Wye (2.5EL WYE) • 2 CT Delta (2 Ct dEL) NOTE: If you are prompted to enter a password, refer to the instructions earlier in this chapter. 3. When you have made your selection, press the Menu button twice. 4. The STOR ALL YES screen appears.
Using the PXM 2000 Series Using Operating Mode Operating Mode is the PXM 2000 Series’ default mode, that is, the standard front panel display. After Startup, the meter automatically scrolls through the parameter screens, if scrolling is enabled. Each parameter is shown for 7 seconds, with a 1 second pause between parameters. Scrolling is suspended for 3 minutes after any button is pressed. 1. Press the Down button to scroll all the parameters in Operating Mode. The currently “Active,” i.e.
Using the PXM 2000 Series Understanding the % of Load Bar The 10-segment LED bar graph at the bottom left of the meter’s front panel provides a graphic representation of Amps. The segments light according to the load, as shown in the % Load Segment Table below. When the Load is over 120% of Full Load, all segments flash “On” (1.5 secs) and “Off” (0.5 secs). Segments none 1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 All Blink www.eaton.
Using the PXM 2000 Series Performing Watt-Hour Accuracy Testing (Verification) To be certified for revenue metering, power providers and utility companies must verify that the billing energy meter performs to the stated accuracy. To confirm the meter’s performance and calibration, power providers use field test standards to ensure that the unit’s energy measurements are correct.
Using the I/O Option Cards 7 USING THE I/O OPTION CARDS Overview The PXM 2000 Series offers extensive I/O expandability. Using the one universal Option Card slot, the unit can be easily configured to accept a new I/O Option card even after installation, without your needing to remove it from the installation. The meter auto-detects any installed Option card. One module of any type outlined in this chapter can be used per meter.
Using the I/O Option Cards 3. Detachable terminal block 2 4. Communication connection for RS485 Port Configuring Option Cards CAUTION! FOR PROPER OPERATION, RESET ALL PARAMETERS IN THE UNIT AFTER HARDWARE MODIFICATION. The meter auto-detects any Option card installed in it. You configure the Option card through the Power Xpert® Ethernet Gateway card. The following sections describe the available Option cards. 7-2 IM02601001E www.eaton.
Using the I/O Option Cards Digital Output (Relay Contact) / Digital Input Card (-1) The Digital Output/Input card is a combination of relay contact outputs for load switching and dry/wet contact sensing digital inputs. The outputs are electrically isolated from the inputs and from the main unit. Specifications The technical specifications at 25 °C are as follows: Power consumption: 0.320W internal Relay outputs.
Using the I/O Option Cards Wiring Diagram Status Inputs S T A T U S C I2 VLoop Common (C) Common (C) C NC NO 1 For dry contacts Inputs (I1,I2) I1 NO 2 For wet contacts Inputs (I1,I2) C NC NO C Relay Contacts NC Relay Outputs Fig. 7.3: Relay Contact (2) / Status Input (2) Card 7-4 IM02601001E www.eaton.
Using the I/O Option Cards Pulse Output (Solid State Relay Contacts) / Digital Input Card (-2) The Pulse Output/Digital Input card is a combination of pulse outputs via solid state contacts and dry/wet contact sensing digital inputs. The outputs are electrically isolated from the inputs and from the main unit. Specifications The technical specifications at 25 °C are as follows: Power consumption: 0.
Using the I/O Option Cards Wiring Diagram Status Inputs S T A T U S 4 3 2 1 C I4 I3 I2 I1 NO C NO C NO C NO C For wet contacts Inputs (I1,I2) For dry contacts Inputs (I1,I2) VLoop Common (C) Common (C) NO Pulse Contacts - Form A C Pulse Outputs Fig. 7.4: Pulse Output (4) / Status Input (4) Card 7-6 IM02601001E www.eaton.
Using the I/O Option Cards 1mA Output Card (-3) The 1mA card transmits a standardized bi-directional 0-1mA signal. This signal is linearly proportional to real-time quantities measured by the meter. The outputs are electrically isolated from the main unit. Specifications: The technical specifications at 25° C at 5kΩ load are as follows: Number of outputs: Power consumption: Signal output range: Max.
Using the I/O Option Cards Wiring Diagram Analog Outputs 0-1 mA Channel C 4 3 2 1 Outputs (1,2,3,4) Iout RL Common (C) Fig 7.5: 4-Channel 0 - 1mA Output Card 7-8 IM02601001E www.eaton.
Using the I/O Option Cards 20mA Output Card (-4) The 20mA card transmits a standardized 0-20 mA signal. This signal is linearly proportional to real-time quantities measured by the meter. The current sources need to be loop powered. The outputs are electrically isolated from the main unit. Specifications The technical specifications at 25° C at 500Ω load are as follows: Number of outputs: Power consumption: Signal output range: Max.
Using the I/O Option Cards Wiring Diagram Analog Outputs 4-20 mA Channel C 4 3 2 1 Outputs (1,2,3,4) Iout RL VLoop Common (C) Fig. 7.6: 4-Channel 4 - 20mA Output Card 7-10 IM02601001E www.eaton.
Using the I/O Option Cards Network Communications with the Power Xpert® 2000 Series (-5) The Power Xpert® Meter Gateway Card provides the PXM 2000 Series with Ethernet capability. NOTE: Network configuration will be done through the card. Specifications The technical specifications at 25° C are as follows: Number of ports: 1 Power consumption: <2.0 Watts internal Data rate: 10/100Mbit Diagnostic features: 100 Mbit LINK and for ACTIVITY.
Using the I/O Option Cards Wiring Diagram RJ45 Plug 8 7 6 5 4 3 2 1 Pin 1 RDCable RD+ TDTD+ Fig. 7.7: PXM 2000 Gateway Card IMPORTANT! The PXM 2000 Gateway Card uses an auto-detecting circuit that automatically switches the transmit and receive in order to properly align communication. Because of this, when you are communicating directly to a meter with a PC or a switch, a straight cable can be used.
Using the I/O Option Cards Performing Network Configuration As with the other Option cards, the PXM 2000 auto-detects the presence of the Gateway card. You configure the Gateway card through the Ethernet connection, using the Power Xpert webpage. See Chapter 10 for instructions. www.eaton.
Using the I/O Option Cards 14 IM02601001E www.eaton.
Introduction to Web Server Pages 8 INTRODUCTION TO WEB SERVER PAGES This chapter is an introduction to the Power Xpert Meter web server pages and describes how to access basic information through them. Each option provides easy access to basic metering functions as well as setup configuration. Other information, such as waveforms, trending graphs, harmonic tables, and phasors are also available.
Introduction to Web Server Pages If you see a blank white or blue page and you don’t see a “site unavailable” message, the likely cause is that you either don’t have Java installed or that it isn’t active. Check the Java console in the Windows Control Panel. Home Page (Default) The Home page displays an overview of the most pertinent current meter readings. From this page you can navigate to the Meter, Power, Quality, I/O, Energy, Events and Setup pages.
Introduction to Web Server Pages If more than one type of graph is available on the page, another drop-down menu in the top center of the page provides options for selecting available graphs.
Introduction to Web Server Pages The Meter Page Printing and Exporting Information Most pages have both Print and Export Data controls. The Print control outputs the current graph to the selected printer. The Export Data function will save the set of data to either a comma-separated values (CSV) file or will display the information in your default .csv file viewer (such as Microsoft Excel). You can select intervals of 5, 15, or 60 minutes and specify the beginning and ending dates for the data set.
Introduction to Web Server Pages I/O Page Events Page The left pane of the events page lists events within the event log. The drop-down menu controls what events are shown in the list, either currently active events or all events (including historical events). You can also acknowledge and close events from this page (this requires the administrative account name and password). The bottom pane shows details about all events.
Introduction to Web Server Pages Events Page, Showing a Non-waveform Event An RMS Waveform Plot The zoom controls provide the ability to view 32, 64, 128, 256, 512, 1024, and 2048 points per view by selecting zoom values 7 (2048 points) through 1 (32 points). The count depends on the number of points in the captured waveform and therefore can’t show more points than was captured. Use the Pan slider to move along the graph timeline.
Introduction to Web Server Pages Setup Page The Setup page is the administrative interface for the meter. Use this to initially configure the meter for operation as well as to fine-tune the configuration to meet your needs. You’ll need the administrative account name and password to modify the setup parameters. Details about using the setup page are covered in the Setup on the Web Pages chapter. Setup Page Help Page The Help page not only provides access to the manual, but also lets you: www.eaton.
Introduction to Web Server Pages Help Page 8-8 IM02601001E www.eaton.
Functions on the Web Server Pages 9 FUNCTIONS ON THE WEB SERVER PAGES Overview The Power Xpert® Meter provides a detailed web interface, providing information for the following main functional categories: • Home page (a summary of current values and navigation to other pages) • Meter • Power • Quality • Energy • I/O • Events • Setup • Help This chapter is not an exhaustive resource, but rather the intent is to provide a general understanding of the information available on each of the m
Functions on the Web Server Pages The Power Xpert® Meter maintains a log of all voltage rms measurements date and time stamps. This information is also available as a trend graph. The min, max, and averages are recorded for each interval.
Functions on the Web Server Pages Meter Page: Voltage Display Current The Power Xpert® Meter measures per phase and average system current and calculates rms values over the period of one second. The meter will maintain a log of all rms measurements with date and time stamps. The same information is available as a trend. The most recent minimum and maximum values are detected for all the channels and are logged with date and time stamps.
Functions on the Web Server Pages Meter Page: Current Display Locating Current Information From the Meter page, click one of the radio buttons listed below Current to select a specific phase or neutral. The page will update to display the selection. To view the trending, waveform, harmonics, or phasor graphs, click the drop-down box located on the top of the page and make a selection.
Functions on the Web Server Pages and make a selection. When Trend and Min/Max is selected, the minimum, maximum, and average values are displayed on the bottom right side of the page with date and time stamps. Harmonics are not available for frequency. Meter Page: Frequency Display Power The Power page contains information about the present power consumption and power factor.
Functions on the Web Server Pages Power Factor (Apparent) Quality The Quality page contains information about the present power quality for PXM 2000 series meters. These meters calculate the following instantaneous values, averaged over a period of 60 cycles: • Percent THD of Current for Phases A, B, and C • Percent THD of Voltage for Phases A, B, and C. Using the drop-down box above the graph, you can select to view this information as a trend, with minimum and maximum values, or as harmonics.
Functions on the Web Server Pages X1 = fundamental value of current or voltage. xn = nth harmonic value of current or voltage. Trend and Min/Max View Like most other real-time measures, the % THD Current and Voltage measurements in the Power Xpert® Meter are trended and minimum and maximum values are logged with date and time stamps. Trend View Harmonics View (PXM 2270/2280/2290 only) The individual harmonics of the THD may be viewed for up to 40 harmonics of the fundamental frequency.
Functions on the Web Server Pages Harmonics Plot Table of Data Points For both views, a table below the graph provides the numeric values as well. This table can be saved as a CSV file. Energy The Power Xpert Meter measures and accumulates three kinds of energy values every 60 cycles: Real Power (Watts), Reactive Power (VAR) and Apparent Power (VA). Real Power and Reactive Power take direction into account, and so are recorded for forward, reverse, net and sum.
Functions on the Web Server Pages are performed for the Total Current, kW Forward/Reverse, Net and Sum; kVar Lead/Lag, Net and Sum and kVA. Fixed and Sliding Demand Fixed demand (Total Current), which is an average system current over time can be set to average current over a range of 5, 15, 30 or 60 minutes. This is known as a fixed window. For example, setting the current demand window to 15 sets the meter to determine the average current over the past 15 minutes and update the value every 15 minutes.
Functions on the Web Server Pages Demand Profile Demand Comparison The Demand Comparison page is similar to the Demand Profile page, but provides a graph you can use to compare two overlaid demand plots from selectable periods of time. You can select to compare plots between: • Today and Yesterday • This Week and Last Week • This Month and Last Month • 2 different Days • 2 different Weeks • 2 different Months Peak demand is shown in the graph as a dashed line. 9-10 IM02601001E www.eaton.
Functions on the Web Server Pages Demand Comparison Plot Calendar Control While viewing the Demand Comparison page, you can also select to compare the information to previous time periods: day-to-day (Demand Comparison only), week-to-week, or month-to-month. If you’re comparing two specified time periods, such as two different days, a calendar control appears when you click either date. Click a day in the calendar to select the beginning and ending dates in the comparison.
Functions on the Web Server Pages and press Ctrl+V. To select the entire table, press Ctrl+A. You can also right-click and select Copy. Events The Power Xpert Meter monitors and logs Out of Limits and Alarm on Value events Events can be used to send e-mail as well as to change the state of internal or external I/ Os. Triggers The following sections highlight available triggers. The meter will use the programmed limits set by the user.
Functions on the Web Server Pages Peak Demand Reverse Watts Peak Demand Sum VARs Peak Demand Sum Watts Peak Demand VAs Percent THD Ib Percent THD Ic Percent THD Van Percent THD Vbn Percent THD Vcn PF App Phase A PF App Phase B PF App Phase C PF Apparent Phase Angle Ia Phase Angle Ib Phase Angle Ic Phase Angle Vab Phase Angle Vbc Phase Angle Vca Reactive Power Reactive Power Phase A Reactive Power Phase B Reactive Power Phase C Real Power Real Power Phase A Real Power Phase B Real
Functions on the Web Server Pages Locating Events From the Events page, you can view either currently active events or a log of all events that have occurred. Click a specific event in the list to display the detailed information about that event at the bottom of the page. You can acknowledge or clear either the currently selected event or all events. The bottom shows details about all events.
Setup on the Web Server Pages 10 SETUP ON THE WEB SERVER PAGES Overview This section provides information about setup, including the settings that are currently active and how to change settings in specific categories. Setup Page When the Setup page opens, a collapsed tree structure is displayed on the left side of the page. Clicking topics within the structure will expand the list to include all the pages available for viewing or configuration.
Setup on the Web Server Pages Login The Login page provides information about the number of subscriptions by instances of Power Xpert Software (PXS) and MODBUS TCP clients. The current user is identified by name. You can also either logout from this page or log in as a different user. Login Page Quick Setup - Meter The Quick Setup - Meter page provides quick access to the most common configuration settings.
Setup on the Web Server Pages Quick Setup Page - Meter Quick Setup - Network The Ethernet/LAN Setup Edit page provides all of the TCP/IP communications settings. You have two choices for configuring the meter: • Fixed (static) IP address • DHCP which resolves to a fixed IP address Eaton does not recommend using a DHCP setup that can randomly assign an IP address from a pool of possible addresses.
Setup on the Web Server Pages Ethernet/LAN Setup Edit In addition to network settings, you can also add location, contact, and asset ID information. Alarm Triggers The meter has three types of triggers: 10-4 • Out of Limits triggers provide set points for issuing alarms for any of the supported electrical measurements. You can also set a hysteresis value for these to avoid rapid, multiple trips from a value that hovers around the set point.
Setup on the Web Server Pages Alarm Triggers - Out of Limits You can use the Out of Limits Triggers page to set high and low cautionary and critical alarms for a wide range of electrical parameters (see page “Triggers” on page 9-12 for a complete list of parameters). For a detailed discussion of triggers, see page “Triggers” on page 9-12. Triggers can cause the following actions: • An event is added to the event log, and can be seen in the Events page.
Setup on the Web Server Pages The Out of Limits Triggers Page In addition to setpoints and alarm messages, you can also set the hysteresis. This is set as a percentage, and is used to dampen “noise” events caused by a value bouncing back and forth across a set point. 10-6 IM02601001E www.eaton.
Setup on the Web Server Pages Out of Limits Setup Edit Page Alarm Triggers - Alarm on Value Use the Alarm on Value Setup page to configure device, option card, or communications status event triggers. You can configure if such events are to be treated as alarms, what the alarm levels are, the messages associated with the events, the limit values, and if the alarms are to be autoclosing.
Setup on the Web Server Pages Alarm Triggers - Waveform Capture Use the Waveform Capture Settings page to configure capture parameters. Parameters you can set are: Samples per Cycle: For the PXM 2280 you can choose between 32 and 64 samples and for the PXM 2290 you can choose either 32, 64, 128, 256, or 512 samples. Cycles per Capture: This depends on the Samples per Cycle setting.
Setup on the Web Server Pages Meter Setup & Commissioning Security Setup See page page 11-1 for detailed information about security best practices. The PXM 2000 meter has two built-in accounts and an additional password for access to data deletion functions from the meter front panel. You cannot change the name of any of the accounts, but you may change the password. • The Numeric Meter Password account provides access to configuration settings and resets from the meter front panel.
Setup on the Web Server Pages accessing a U.S. Government information system, system usage may be monitored, and unauthorized use of the system is prohibited. Refer to your system administration group for guidance about exact wording. Access Control Edit Page Metering - Demand The Demand Setup page allows you to select either a fixed window or sliding window and the respective intervals in minutes. A fixed window setting allows you to select one interval period.
Setup on the Web Server Pages Fixed Settings Sliding Settings Communications Settings Under Communications, you can set the serial communications parameters, the email settings (including the mail server and recipients), as well as the setup parameters for SNMP. See page page 11-1 for detailed information about security best practices. Communications Settings - Com 2 Setup You can set the protocol, Modbus address, baud rate, and response delay for the RS485 serial connection.
Setup on the Web Server Pages Serial Communications Setup Page Communications Settings - BACnet/IP The PXM 2250-2290 meters have support for communications via BACnet/IP, including: • Support for BBMD for connecting across BACnet/IP routers. • Limited BACnet router capability to create a “virtual subnet” that presents the meter and option card as separate, virtual BACnet devices. The virtual subnet must be assigned a unique network number within your BACnet/IP network.
Setup on the Web Server Pages After setting the Routed network number, the meter will provide a setup page in which you can set the following: Identification: These fields provide the unique identifiers for the gateway card itself. They include: • Base ID for Auto-assign: You can set a base ID number, and the meter will use this number to automatically generate the object-identifier for the network card, the meter itself, and the option card.
Setup on the Web Server Pages BACnet/IP Setup Page Communications Settings - E-mail Setup The PXM 2000 meter provides a highly configurable capability to report on meter activity via email. You can configure up to 10 separate recipients. This is just like configuring an email application such as Outlook Express or Thunderbird. If you are unsure as to how to do this, ask your information technologies group or the person in charge of your mail server for assistance.
Setup on the Web Server Pages ent through the Recipient drop-down list and then configuring the recipient’s address information by clicking the Edit button.
Setup on the Web Server Pages SNMP Setup Edit Page Option Cards The PXM 2000 meter supports the following types of option cards: • Digital Output (Relay Contact) / Digital Input Card • Pulse Output (Solid State Relay Contacts) / Digital Input Card • 1mA Output Card • 20mA Output Card Electrical specifications and installation information for each card is covered in Chapter 7.
Setup on the Web Server Pages • The Enabled check boxes activate the Above and Below settings. When active, the output is triggered for when that condition occurs. Once active, you can click any of the Setpoint and Hysteresis fields and edit their contents. Hardware Limits Edit Page You can use the Digital Input Setup Edit page to configure the relay inputs. You can assign labels for the open and closed states as well as the accumulator.
Setup on the Web Server Pages Digital Input Setup Edit Page Use the Relay Outputs Setup Edit page to set the output behavior of the relays. The count reflects the number of times the relay has energized. (You can define the labels, state names, operating delays, and configure the accumulator. The Divisor is a compression factor for the accumulator, and you can select 1, 10, 100, 1000, 10000, and 100000.
Setup on the Web Server Pages Relay Output Setup Edit Page Pulse Output (Solid State Relay Contacts) / Digital Input Card This option card has: • Four pulse outputs via solid state contacts. • Four wet/dry contact sensing digital inputs. Accumulators in the software count the pulses of the Inputs and Outputs (the accumulators are shown on the I/O page. Typically, this card is used in a sub-metering application where a pulse output is needed.
Setup on the Web Server Pages The Set Limit Channel dialog box associates a meter measure, like kW Demand or Phase B current, with each of the outputs, and gets a pulse train whose rate reflects the present value of that measure. Digital Input Setup Edit Page You can set up to four outputs for your card. You can define the labels, state names, and configure the accumulator. You can also specify the phase source and measurement.
Setup on the Web Server Pages Set Limit Channel Dialog Box. Option Cards - 0-1 mA Analog Output Card and 4-20 mA Output Card The 0-1mA Output Option Card is an analog communication card, which transmits a standard, bi-directional 0-1 milliamp signal. Bi-derectional is useful when you want the output (-1 to 1 V) to reflect the sign of a measure that goes negative (like VAR).
Setup on the Web Server Pages Setting the Source Measurement System Setup The System Setup page is divided into two sections: Hardware and System Firmware. Hardware Setup - Faceplate Setup You can configure the meter’s faceplate display. Options include: • Phases Displayed: A; A and B; A, B, and C. This field determines which phases display on the faceplate. For example, if you select A and B, only those two phases will be displayed on the faceplate.
Setup on the Web Server Pages synch, an IP address of the NTP server should be set. When selecting NTP (Network Time Protocol) as the Time Sync Source, at least one IP Address must be entered (as many as three NTP server IP addresses may be entered). A list of public NTP servers is available at: http://support.ntp.org/bin/view/Servers/WebHome. Note: The Time Zone and Date format settings only affect logs and e-mails.
Setup on the Web Server Pages 4. Fill out the form (if required). 5. Download the firmware to your local file system. 6. Click the Browse button. 7. Select the firmware file. 8. Click the Open button. Note: On rare instances (such as a problem occurring in the firmware upgrade) you may need to reload the meter page after rebooting the meter. It can take around five minutes for values to display after a reboot.
Setup on the Web Server Pages System Hardware Page www.eaton.
10-26 IM02601001E www.eaton.
Securing the Power Xpert Meter 11 SECURING THE POWER XPERT METER This chapter outlines how to harden network security for the PXM 2000 Series meter. The meter communicates via Ethernet and uses the network security mechanisms outlined in this chapter. Inbound/Outbound TCP/IP Ports Access to the PXM 2000 Series meter is restricted by ports and can be restricted by trusted hosts.
Securing the Power Xpert Meter • Disable SNMP v1 if not needed. Use SNMP v3 only if you can. See page page 11-5. • Disable SNMP v3 if not needed. See page page 11-5. • Remove all the SNMP trap recipients if traps are not needed. See page page 11-5. • Remove all email recipients if email is not needed. See page page 11-7. • Change the default port for Modbus TCP. See page page 11-3. • Change the default port for HTTP and HTTPS. See page page 11-3.
Securing the Power Xpert Meter 2. Click the Setup tab. 3. Navigate to the Meter Setup > Security > Passwords page. 4. Click the Edit Password button for each of the Network users and change the default values. If you didn’t log in earlier, you must enter the admin account user name and password. 5. You must enter the new password twice and both entries must match to change the new password. 6. Click OK. 7. Click the Edit Numeric Password button and change the default four digit numeric password. 8.
Securing the Power Xpert Meter 5. If you didn’t log in earlier, you must enter the admin account user name and password. The following comprise Eaton’s recommendations for Access Control best practices: Trusted IPs/hostnames separated by semi-colons(;) If you are using SNMP, Modbus TCP, BACnet/IP or FTP, you should specify the IP addresses or host names for one or more computers that are to be allowed access to the meter and then enable the trusted host feature for that protocol.
Securing the Power Xpert Meter Access Control Edit Page SNMP Hardening As noted in the previous section, you can specify a set of trusted hosts for SNMP. On the SNMP setup page, you can disable one or both versions of the SNMP protocol (the older version 1 or the more secure version 3). You should disable any version you are not using. We recommend using version 3 only if possible as this is more secure.
Securing the Power Xpert Meter SNMP Setup Edit Page Accessible Folders The PXM 2000 Series meter provides user documentation and SNMP MIB files through its web UI. These documents are also available from the meter via a read-only user-accessible folder. This is meant for convenient access to these publicly available files for the PXM 2000 Series meter.
Securing the Power Xpert Meter Example Contents of the docs Folder Email Security The PXM 2000 Series meter can be set to send emails whenever an alarm or event occurs or an alarm is cleared. It can also be configured to send periodic status emails. Eaton recommends that you should periodically examine this list and remove any email addresses that are no longer required. To access the Email settings: To access the PXM 2000 Series meter security settings: 1. Access the meter home page.
Securing the Power Xpert Meter E-Mail Setup Edit Page Enabling Root Certificate Authority in Internet Explorer You can improve the security of your PXM 2000 Series meter on the web by installing a root certificate authority (CA). A CA is a trusted third-party organization that issues digital certificates for use with encrypted digital transactions. The digital certificate guarantees that the company holding a certificate is who it claims to be.
Securing the Power Xpert Meter 3. If the security certificate problem page appears, you’ll next see the following security warning dialog box. Click Yes. Warning: Security dialog box 4. The install CA certificate page appears. Click the Root CA Certificate link. Install CA certificate page 5. Click the Open button. www.eaton.
Securing the Power Xpert Meter Figure 2. File download dialog box 6. In the Certificate dialog box, click the Install Certificate button. NOTE: The certificate cannot be verified yet because it is issued by a nontrusted CA. Figure 3. Certification Path Window 7. Select the Certification Path tab. On the tab, select the line with PowerXpert followed by a series of hexadecimal digits. 11-10 IM02601001E www.eaton.
Securing the Power Xpert Meter 8. Click the View Certificate button. The Certificate dialog box appears. 9. Click the Install Certificate button. The Certificate Import Wizard appears. www.eaton.
Securing the Power Xpert Meter Certificate Import Wizard f Click the Next button. The store dialog box appears. Certificate Import Wizard - store dialog 10. Select Place all certificates in the following store and then click Browse. 11. Select Trusted Root Certificate Authorities and then click OK. 11-12 IM02601001E www.eaton.
Securing the Power Xpert Meter 12. Click Next. Certificate Import Wizard - successfully stored 13. The certificate wizard displays a completed dialog. Click Finish. The Security Warning dialog box will appear. Security Warning dialog box www.eaton.
Securing the Power Xpert Meter 14. Click Yes to install the CA. 15. A message box opens to verify that the import was successful. Import Successful message box 16. Click OK. 17. Click OK to close the dialog box. The installation process is complete. You can now access the meter using the HTTPS protocol (for example, https://192.168.1.1/). 11-14 IM02601001E www.eaton.
Navigation Maps A NAVIGATION MAPS Introduction You can configure the meter and perform related tasks using the buttons on the meter face. • Chapter 6 contains a description of the buttons on the meter face and instructions for programming the meter using them. • The meter can also be programmed using software. See chapter 8 for instructions on programming the meter using the Configuration software. Navigation Maps (Sheets 1 to 4) The PXM 2000 Series Navigation Maps begin on the next page.
Navigation Maps Main Menu Screens (Sheet 1) A-2 IM02601001E www.eaton.
Navigation Maps Operating Mode Screens (Sheet 2) www.eaton.
Navigation Maps Reset Mode Screens (Sheet 3) A-4 IM02601001E www.eaton.
Navigation Maps Configuration Mode Screens (Sheet www.eaton.
Navigation Maps A-6 IM02601001E www.eaton.
DIP Switch Description B DIP SWITCH DESCRIPTION The DIP Switch definitions for the Gateway Card are listed in the following table. S1 Position Number www.eaton.com OFF Position (Default) ON Position 1 Enable previously stored network configuration settings (Normal mode). Override network settings to assign a private IP address (Configuration mode); the port is set to 192.254.1.1. 2 Reserved Reserved 3 Normal behavior Reset the HTTP passwords to the defaults on boot up (user and admin).
DIP Switch Description B-2 IM02601001E www.eaton.
Configuration Management C CONFIGURATION MANAGEMENT This appendix covers: • Backing up and restoring configuration settings • Replacing a Meter • Monitoring changes to configuration settings.
Configuration Management Save/Restore Configuration Page Replacing a Meter If you are replacing a meter, you can use the backup file for your meter’s configuration to configure the new meter with the same settings as the meter it replaced (see the previous section). While following the installation instructions in the Quick Start Guide, instead of manually configuring the meter on the bench, use the previous meter’s configuration file to set the meter parameters.
Configuration Management • Reset the HTTP passwords. • Reset return the meter to factory defaults. To change DIP switch settings, you must remove the Gateway Card from the meter. The best practice for this is to remove the meter to a workbench. IMPORTANT! When the meter was originally installed, you should have recorded information concerning the IP, subnet mask, and DNS servers. You will need this information to reconfigure the meter.
Configuration Management 13 and 6 position connectors 13 position connector GND L(+) N(-) 6 position network connector Remove Meter from Panel When removing the meter keep the mounting hardware (screws, washers, etc.) in a safe place for use when re-installing the meter. 1. For ANSI installations remove the four nuts and washers. 2. Move the meter to a workbench.
Configuration Management DIP Switches on the Gateway Card Gateway Card, removed from the meter. DIP switch ON 1 4. DIP switch, showing switches 1, 3 and 6. 2 3 4 5 6 7 8 Move the appropriate switch to the ON position: S1 Position Number OFF Position (Default) ON Position 1 Enable previously stored network configuration settings. Override network settings to assign a private IP address (Configuration mode); the port is set to 192.254.1.1.
Configuration Management 5. Insert the Gateway Card into meter slot 2 using the meter’s built-in card guides. Use care to correctly locate the card in the guides. An incorrectly installed card may be damaged or may damage the meter. Slide the card carefully into the meter until it stops. Gently push on the card until it “clicks” into place. 6. Attach the power cord. If an AUX power cord was assembled using a spare 13 position connector then insert the connector into the socket.
Configuration Management Checking Gateway Card Indicators First, ensure power is applied to the meter. Location of Gateway Card There are four indicator LEDs on the Gateway Card labeled: Status, DHCP, Ident, and Power. When power is first applied all the lights should be off for a few seconds and then the Power light will illuminate. This indicates the card has power and is running.
Configuration Management Settings Button 3. Ensure the Keep Temporary Files on My Computer check box is cleared. Keep Temporary Files on My Computer check box 4. Connect the PC to the Gateway Card through the seven-foot Ethernet cable shipped with the meter. There are two green lights (LEDs) located on the Gateway Card’s Ethernet port.
Configuration Management c. In the Control Panel, click Network Connections and right-click Local Area Connection. Select Properties from the shortcut menu. d. Click the Properties button. e. In the Properties dialog box, select Internet Protocol (TCP/IP) and click the Properties button. f. In the Internet Protocol (TCP/IP) Properties dialog box, select Use the following IP address and enter the following in the IP address field: 192.168.1.100 g. Click OK throughout the various dialog boxes. 6.
Configuration Management Meter Home Page 7. Click the Setup button. The Setup page will appear. 8. Locate and click the open icon to the left of the Quick Setup folder. The folder opens to show two subfolders: Meter and Network. Opening the Quick Setup Folder 9. Click the Network folder. 10. Click the Edit button. Edit Button (on the right of the page) A Login dialog box appears. C-10 IM02601001E www.eaton.
Configuration Management 11. The default Username is admin and the default Password is admin. Log in using these credentials. Login dialog 12. If you successfully logged in as admin you may now configure the card for the settings specified by your network administrator. Refer to the previously recorded network settings. You can also enter such optional information as the meter’s location, who to contact in case of problems, etc. 13. When you’ve completed configuration, click the OK button.
Configuration Management Restart the Gateway Card The Gateway Card restart push-button switch is located behind the hole in the card face plate closest to the LED labelled DHCP. This switch is used to restart just the Gateway Card (not the meter) should it be necessary to recover from some abnormal condition. Momentarily press the switch by pushing a small device into the hole to activate the switch. Reset Switch 100 Reset switch Act Status DHCP Ident Power Reinstalling the Meter 1.
Configuration Management Connectors 13 position connector GND L(+) N(-) 6 position network connector 2. If a Modbus network was connected remove the six position network connector. 3. Return the meter to the mounting panel using any hardware removed in previous steps. 4. Reconnect the current sensing (CT or direct connections) wires. 5. If an AUX cable was not used, reconnect the wires to the 13 position connector. Otherwise plug the wired connector into the meter. 6.
Configuration Management 12. If the Ethernet is active then the ACT light located at the Ethernet cable should be flickering. Location of LEDs C-14 IM02601001E www.eaton.
