5115 500–1400 VA www.powerware.
Class B EMC Statements FCC Part 15 NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Requesting a Declaration of Conformity Units that are labeled with a CE mark comply with the following harmonized standards and EU directives: 쑺 Harmonized Standards: EN 50091-1-1 and EN 50091-2; IEC 60950 Third Edition 쑺 EU Directives: 73/23/EEC, Council Directive on equipment designed for use within certain voltage limits 93/68/EEC, Amending Directive 73/23/EEC 89/336/EEC, Council Directive relating to electromagnetic compatibility 92/31/EEC, Amending Directive 89/336/EEC relating to EMC The EC Decl
Special Symbols The following are examples of symbols used on the UPS to alert you to important information: CAUTION Risk of Electric Shock Do Not Open Cover CAUTION To reduce the risk of electric shock, Do not remove cover (or back) No user-serviceable parts inside Refer servicing to the factory RISK OF ELECTRIC SHOCK - Indicates that a risk of electric shock is present and the associated warning should be observed.
Table of Contents 1 Powerware 5115 – One of the Best! . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Inspecting the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing the UPS . . . . . . . . . . . . . . .
Table of Contents 7 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 8 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Audible Alarms and UPS Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Silencing an Audible Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1 Powerware 5115 – One of the Best! The Powerware® 5115 uninterruptible power system (UPS) protects your sensitive electronic equipment from basic power problems such as power failures, power sags, power surges, brownouts, and line noise. Power outages can occur when you least expect it and power quality can be erratic. These power problems have the potential to corrupt critical data, destroy unsaved work sessions, and damage hardware — causing hours of lost productivity and expensive repairs.
Powerware 5115 – One of the Best! Providing outstanding performance and reliability, the Powerware 5115’s unique benefits include the following: 쑺 Advanced Battery Management (ABM®) technology doubles battery service life, optimizes recharge time, and provides a warning before the end of useful battery life. 쑺 Buck and Boost voltage regulation ensures consistent voltage to your load by correcting voltage fluctuations.
Chapter 2 Safety Warnings Read the following precautions before you install the UPS. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions that you should follow during installation and maintenance of the UPS and batteries. Please read all instructions before operating the equipment and save this manual for future reference. DANGER This UPS contains LETHAL VOLTAGES. All repairs and service should be performed by AUTHORIZED SERVICE PERSONNEL ONLY.
Safety Warnings CAUTION 쑺 The wall outlet must be within 2 meters of the equipment and accessible to the operator. 쑺 Batteries can present a risk of electrical shock or burn from high short-circuit current. The following precautions should be observed: 1) Remove watches, rings, or other metal objects; 2) Use tools with insulated handles; 3) Do not lay tools or metal parts on top of batteries; 4) Disconnect charging source prior to connecting or disconnecting battery terminals.
Safety Warnings Sikkerhedsanvisninger VIGTIGE SIKKERHEDSANVISNINGER GEM DISSE ANVISNINGER DENNE BRUGERVEJLEDNING INDEHOLDER VIGTIGE SIKKERHEDSANVISNINGER FARE Denne UPS indeholder LIVSFARLIG HØJSPÆNDING. Alle reparationer og vedligeholdelse bør kun udføres af en AUTORISERET SERVICETEKNIKER. Ingen af UPS’ens indvendige dele kan repareres af brugeren. ADVARSEL! 쑺 Denne UPS indeholder egen energiforsyning (batterier). Udgangsnetstikkene kan lede strøm, selv når UPS’en ikke er tilsat en AC-energikilde.
Safety Warnings Belangrijke Veiligheidsinstructies BELANGRIJKE VEILIGHEIDSINSTRUCTIES BEWAAR DEZE INSTRUCTIES DEZE HANDLEIDING BEVAT BELANGRIJKE VEILIGHEIDSINSTRUCTIES GEVAAR Deze UPS bevat LEVENSGEVAARLIJKE ELEKTRISCHE SPANNING. Alle reparaties en onderhoud dienen UITSLUITEND DOOR ERKEND SERVICEPERSONEEL te worden uitgevoerd. Er bevinden zich GEEN ONDERDELEN in de UPS die DOOR DE GEBRUIKER kunnen worden GEREPAREERD. WAARSCHUWING 쑺 Deze UPS bevat zijn eigen energiebron (batterijen).
Safety Warnings Tarkeita Turvaohjeita TÄRKEITÄ TURVAOHJEITA - SUOMI SÄILYTÄ NÄMÄ OHJEET TÄMÄ OPAS SISÄLTÄÄ TÄRKEITÄ TURVAOHJEITA VAARA Tämä UPS sisältää HENGENVAARALLISIA JÄNNITTEITÄ. Kaikki korjaukset ja huollot on jätettävä VAIN VALTUUTETUN HUOLTOHENKILÖN TOIMEKSI. UPS ei sisällä MITÄÄN KÄYTTÄJÄN HUOLLETTAVIA OSIA. VAROITUS 쑺 Tämä UPS sisältää oman energialähteen (akuston). Ulostuloliittimissä voi olla jännite, kun UPS ei ole liitettynä verkkojännitteeseen.
Safety Warnings Consignes de sécurité CONSIGNES DE SÉCURITÉ IMPORTANTES CONSERVER CES INSTRUCTIONS CE MANUEL CONTIENT DES CONSIGNES DE SÉCURITÉ IMPORTANTES DANGER! Cet onduleur contient des TENSIONS MORTELLES. Toute opération d’entretien et de réparation doit être EXCLUSIVEMENT CONFIÉE A UN PERSONNEL QUALIFIÉ AGRÉÉ. AUCUNE PIÈCE RÉPARABLE PAR L’UTILISATEUR ne se trouve dans l’onduleur. AVERTISSEMENT! 쑺 Cet onduleur renferme sa propre source d’énergie (batteries).
Safety Warnings Sicherheitswarnungen WICHTIGE SICHERHEITSANWEISUNGEN AUFBEWAHREN. DIESES HANDBUCH ENTHÄLT WICHTIGE SICHERHEITSANWEISUNGEN. WARNUNG Die USV führt lebensgefährliche Spannungen. Alle Reparatur- und Wartungsarbeiten sollten nur von Kundendienstfachleuten durchgeführt werden. Die USV enthält keine vom Benutzer zu wartenden Komponente ACHTUNG 쑺 Diese USV ist mit einer eigenen Energiequelle (Batterie) ausgestattet.
Safety Warnings • •••••••••••••• • •• •••••• •• • • • ••• • • • • • • •• • • •• • •• •• • • • •• • •• • • •• • ••• • • • • •• • •• • • • • • • • • • •• •• •• • • • •• • • ••• • • • ••• • • • • • • •• • • •• • •• •• • • •• • • • • • • • •• •• • • • • • • •• • • • • • • • • • • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • • •• • • • • •• • • • • • • • • • •• • • •• • • • • • • • • • • • • • •• • • • • • • • • • •• • • • • • • • • • • • • • • • • • •• • • • • • • • • • • • • • •• • • • • • • •
Safety Warnings Avvisi di sicurezza IMPORTANTI ISTRUZIONI DI SICUREZZA CONSERVARE QUESTE ISTRUZIONI QUESTO MANUALE CONTIENE IMPORTANTI ISTRUZIONI DI SICUREZZA PERICOLO la TENSIONE contenuta in questo gruppo statico di continuità è LETALE. Tutte le operazioni di riparazione e di manutenzione devono essere effettuate ESCLUSIVAMENTE DA PERSONALE TECNICO AUTORIZZATO. All’interno del gruppo statico di continuità NON vi sono PARTI RIPARABILI DALL’UTENTE.
Safety Warnings 쑺 Non gettare mai le batterie nel fuoco poichè potrebbero esplodere se esposte alle fiamme. 쑺 Mai aprire nè mutilare le batterie poichè l’elettrolita da esse rilasciato è nocivo alla cute e agli occhi e può essere altamente tossico. Viktig Sikkerhetsinformasion FARLIG Denne UPS’en inneholder LIVSFARLIGE SPENNINGER. All reparasjon og service må kun utføres av AUTORISERT SERVICEPERSONALE. BRUKERE KAN IKKE UTFØRE SERVICE PÅ NOEN AV DELENE i UPS’en.
Safety Warnings Regulamentos de Segurança INSTRUÇÕES DE SEGURANÇA IMPORTANTES GUARDE ESTAS INSTRUÇÕES ESTE MANUAL CONTÉM INSTRUÇÕES DE SEGURANÇA IMPORTANTES CUIDADO A UPS contém VOLTAGEM MORTAL. Todos os reparos e assistência técnica devem ser executados SOMENTE POR PESSOAL DA ASSISTÊNCIA TÉCNICA AUTORIZADO. Não há nenhuma PEÇA QUE POSSA SER REPARADA PELO USUÁRIO dentro da UPS. ADVERTÊNCIA 쑺 Esta UPS contém sua própria fonte de energia (baterias).
Safety Warnings Предупреждения по мерам безопасности ВАЖНЫЕ УКАЗАНИЯ ПО МЕРАМ БЕЗОПАСНОСТИ СОХРАНИТЕ ЭТИ УКАЗАНИЯ ДАННОЕ РУКОВОДСТВО СОДЕРЖИТ ВАЖНЫЕ УКАЗАНИЯ ПО МЕРАМ БЕЗОПАСНОСТИ ОПАСНО В данном ИБП имеются СМЕРТЕЛЬНО ОПАСНЫЕ НАПРЯЖЕНИЯ. Все работы по ремонту и обслуживанию должны выполняться ТОЛЬКО УПОЛНОМОЧЕННЫМ ОБСЛУЖИВАЮЩИМ ПЕРСОНАЛОМ. Внутри ИБП нет узлов, ОБСЛУЖИВАЕМЫХ ПОЛЬЗОВАТЕЛЕМ. ПРЕДУПРЕЖДЕНИЕ 쑺 Данный ИБП содержит собственные источники энергии (аккумуляторы).
Safety Warnings Advertencias de Seguridad INSTRUCCIONES DE SEGURIDAD IMPORTANTES GUARDE ESTAS INSTRUCCIONES ESTE MANUAL CONTIENE INSTRUCCIONES DE SEGURIDAD IMPORTANTES PELIGRO Este SIE contiene VOLTAJES MORTALES. Todas las reparaciones y el servicio técnico deben ser efectuados SOLAMENTE POR PERSONAL DE SERVICIO TÉCNICO AUTORIZADO. No hay NINGUNA PARTE QUE EL USUARIO PUEDA REPARAR dentro del SIE. ADVERTENCIA 쑺 Este SIE contiene su propia fuente de energía (las baterías).
Safety Warnings Säkerhetsföreskrifter VIKTIGA SÄKERHETSFÖRESKRIFTER SPARA DESSA FÖRESKRIFTER DENNA BRUKSANVISNING INNEHÅLLER VIKTIGA SÄKERHETSFÖRESKRIFTER FARA Denna UPS-enhet innehåller LIVSFARLIG SPÄNNING. ENDAST AUKTORISERAD SERVICEPERSONAL får utföra reparationer eller service. Det finns inga delar som ANVÄNDAREN KAN UTFÖRA SERVICE PÅ inuti UPS-enheten. VARNING 쑺 Denna UPS-enhet har en egen energikälla (batterier).
Chapter 3 Installation This section explains: 쑺 Equipment inspection 쑺 UPS installation 쑺 UPS rear panels Inspecting the Equipment If any equipment has been damaged during shipment, keep the shipping cartons and packing materials for the carrier or place of purchase and file a claim for shipping damage. If you discover damage after acceptance, file a claim for concealed damage.
Installation 1 Connect communication cable from computer to UPS (optional) NOTE This is a typical setup; your setup may vary. 5 Press the ON button (on the front panel) 2 & 3 Connect UPS to power 4 Connect equipment to UPS Figure 2. Typical UPS Installation (120V Model Shown) 3. Plug the UPS power cord into a power outlet. Verify that the circuit has an upstream overcurrent protection of 15A for 120V models or 10A for 230V models. 4. Plug the equipment to be protected into the UPS output receptacles.
Installation UPS Rear Panels This section shows the rear panels of the Powerware 5115 models. DIP Switches USB Port Site Wiring Fault Indicator Network Transient Protector Communication Port Four 5-15 Receptacles Input Overcurrent Protector 6-ft Power Cord with 5-15 Plug Figure 3.
Installation Communication Port DIP Switches USB Port Site Wiring Fault Indicator Network Transient Protector Two 5-15 Receptacles Fan Four 5-15 Receptacles Input Overcurrent Protector 6-ft Power Cord with 5-15 Plug Figure 5. 1000 VA, 120V Rear Panel Communication Port DIP Switches USB Port Site Wiring Fault Indicator Network Transient Protector Fan Six 5-15 Receptacles Input Overcurrent Protector 6-ft Power Cord with 5-15 Plug Figure 6.
Installation Network Transient Protector Communication Port DIP Switches USB Port Four 10A, IEC-320 Receptacles 10A, IEC-320 Input Connector Figure 7. 500 VA, 230V Rear Panel DIP Switches Communication Port USB Port Network Transient Protector Four 10A, IEC-320 Receptacles Fan 10A, IEC-320 Input Connector Figure 8. 750 VA, 230V Rear Panel Powerware® 5115 Tower UPS (500–1400 VA) User’s Guide S 05146640 Rev C www.powerware.
Installation DIP Switches Communication Port USB Port Network Transient Protector Four 10A, IEC-320 Receptacles Fan Two 10A, IEC-320 Receptacles 10A, IEC-320 Input Connector Figure 9. 1000 VA, 230V Rear Panel DIP Switches Communication Port USB Port Network Transient Protector Fan Six 10A, IEC-320 Receptacles 10A, IEC-320 Input Connector Figure 10. 1400 VA, 230V Rear Panel 22 Powerware® 5115 Tower UPS (500–1400 VA) User’s Guide S 05146640 Rev C www.powerware.
Chapter 4 Operation This section describes: 쑺 Turning the UPS on and off 쑺 Starting the UPS on battery 쑺 Standby mode 쑺 The UPS front panel and indicators 쑺 Initiating the self-test Turning the UPS On After the UPS is connected to a power outlet, the UPS enters Standby mode. To turn on the UPS, press and hold the button until you hear the UPS beep (approximately two seconds). After the UPS is turned on, it indicator conducts a self-test and enters Normal mode.
Operation Standby Mode When the UPS is turned off and remains plugged into a power outlet, the UPS is in Standby mode. All indicators are off and power is not available to your equipment. The battery recharges when necessary. NOTE For 220–240V models, the output receptacles may remain electrically live (up to 110–120V). Unplug the UPS to ensure power is not available to the output receptacles. UPS Front Panel The UPS front panel indicates the UPS status and also identifies potential power problems.
Chapter 5 Additional UPS Features This section describes: 쑺 Changing the voltage configuration 쑺 Using the USB or DB-9 communication port 쑺 The Network Transient Protector Voltage Configuration The DIP switches on the rear panel of each unit (see Figure 12) are used to configure the output voltage and input voltage range. 1. The UPS must be completely shutdown. To turn off the UPS, press and hold the button for two seconds and then unplug the UPS from the power outlet. 2.
Additional UPS Features Table 1. DIP Switch Settings 120V Models Output Voltage Input Voltage Range DIP Switch 1 DIP Switch 2 110V 99V-116V ON OFF/ON 120V* 108V–127V* OFF OFF/ON DIP Switch 1 DIP Switch 2 230V Models Output Voltage Input Voltage Range 220V 198V–233V ON OFF 230V* 207V–243V* OFF OFF/ON 240V 216V–254V ON ON *Default position Communication Options The UPS is equipped with a USB and a DB-9 communication port.
Additional UPS Features DB-9 Communication Port To establish communication between the UPS and a computer, connect your computer to the UPS communication port using the supplied communication cable. When the communication cable is installed, power management software can exchange data with the UPS. The software polls the UPS for detailed information on the status of the power environment. If a power emergency occurs, the software initiates the saving of all data and an orderly shutdown of the equipment.
Additional UPS Features Network Transient Protector The Network Transient Protector, shown in Figure 15, is located on the rear panel and has jacks labeled IN and OUT. This feature accommodates a single RJ-45 (10BaseT) network connector. Low voltage models can also accommodate an RJ-11 telephone connector that provides protection for modems, fax machines, or other telecommunications equipment.
Chapter 6 UPS Maintenance This section explains how to: 쑺 Care for the UPS and batteries 쑺 Replace the batteries 쑺 Test new batteries 쑺 Recycle used batteries UPS and Battery Care For the best preventive maintenance, keep the area around the UPS clean and dust-free. If the atmosphere is very dusty, clean the outside of the system with a vacuum cleaner. For full battery life, keep the UPS at an ambient temperature of 25°C (77°F).
UPS Maintenance Replacing Batteries NOTE DO NOT DISCONNECT the batteries while the UPS is in Battery mode. With the hot-swappable battery feature, UPS batteries can be replaced easily without turning the UPS off or disconnecting the load. If you prefer to remove input power to change the battery, press and hold the button for two seconds and then unplug the UPS. Consider all warnings, cautions, and notes before replacing batteries.
UPS Maintenance Use the following steps to replace the batteries: 1. Pull the top left corner forward and remove the front panel. 2. Slide up and remove the metal battery cover. 3. 500 VA models. Disconnect the red battery cable and then disconnect the black battery cable. Pull the battery out onto a flat, stable surface. 500 VA Powerware® 5115 Tower UPS (500–1400 VA) User’s Guide S 05146640 Rev C www.powerware.
UPS Maintenance 4. 750/1000 VA models. Disconnect the red battery cable and then pull the battery out onto a flat, stable surface. Disconnect the black battery cable to the UPS as shown. 750/1000 VA 5. 1400 VA models. Disconnect the red battery cable and then pull the battery out onto a flat, stable surface. Remove the battery tie around the black cable set and disconnect the black battery cable to the UPS as shown. 1400 VA 32 Powerware® 5115 Tower UPS (500–1400 VA) User’s Guide S 05146640 Rev C www.
UPS Maintenance 6. Replace the battery. See “Recycling the Used Battery” on page 34 for proper disposal. 7. Connect the black battery cable to the new battery and then connect the red battery cable. 8. Reinstall the battery. 9. Reinstall the metal battery cover and front panel. Testing New Batteries NOTE Allow batteries to charge for 6 to 24 hours before testing. Press and hold the button for three seconds to initiate a self-test.
UPS Maintenance Recycling the Used Battery Contact your local recycling or hazardous waste center for information on proper disposal of the used battery. WARNING 쑺 Do not dispose of the battery or batteries in a fire. Batteries may explode. Proper disposal of batteries is required. Refer to your local codes for disposal requirements. 쑺 Do not open or mutilate the battery or batteries. Released electrolyte is harmful to the skin and eyes. It may be toxic.
Chapter 7 Specifications This section provides the following specifications for the Powerware 5115 models: 쑺 Dimensions and weights 쑺 Electrical input and output 쑺 Environmental and safety 쑺 Battery Table 3. Model List and Mechanical 120V Models 230V Models UPS Models PW5115 500 PW5115 750 PW5115 1000 PW5115 1400 PW5115 500i PW5115 750i PW5115 1000i PW5115 1400i UPS Dimensions (WxHxD) 500 VA: 15.0 x 19.3 x 27.0 cm (5.9I x 7.6I x 10.6I) 750–1000 VA: 15.0 x 19.3 x 33.5 cm (5.9I x 7.6I x 13.
Specifications Table 5. Electrical Output 120V Models 230V Models Power Levels (rated at nominal inputs) 500 VA, 320W 750 VA, 500W 1000 VA, 670W 1400 VA, 950W Power Factor 500 VA, 0.64 750–1400 VA, 0.
Specifications Table 7. Battery Configuration 500 VA: (1) 12V, 9 Ah internal battery 750 VA: (2) 12V, 7 or 7.
Specifications 38 Powerware® 5115 Tower UPS (500–1400 VA) User’s Guide S 05146640 Rev C www.powerware.
Chapter 8 Troubleshooting This section explains: 쑺 UPS alarms and conditions 쑺 How to silence an alarm 쑺 Site wiring fault on 120V models 쑺 Service and support Audible Alarms and UPS Conditions The UPS has an audible alarm feature to alert you of potential power problems. Use Table 9 to determine and resolve the UPS alarms and conditions.
Troubleshooting Site Wiring Fault (120V Models Only) The Site Wiring Fault indicator on the UPS rear panel illuminates if the ground wire connection does not exist or the line and neutral wires are reversed in the line receptacle. This indicator stays on until the condition is resolved. Have a qualified electrician correct the wiring fault. The UPS operates when the indicator is illuminated, but does not provide rated noise and surge suppression. Table 9.
Troubleshooting Alarm or Condition Possible Cause Action 1 beep every 2 seconds. The battery is running low. Two minutes or less of battery power remains (depending on load configuration and battery charge). Save your work and turn off your equipment. The alarm cannot be silenced. 1 beep every 2 seconds. The UPS is running on battery power because the input voltage is too high or too low. Correct the input voltage, if possible.
Troubleshooting Alarm or Condition 42 Possible Cause Action Continuous beep. UPS fan fault (750–1400 VA models only). Save your work and turn off your equipment. Turn off the UPS. Contact your service representative. 3 beeps every 10 seconds. Failed attempt to start the UPS on battery. Plug the UPS into a power outlet for 24 hours to charge the battery. After charging the battery, press and hold the button for 3 seconds; then check the indicator.
Troubleshooting Service and Support If you have any questions or problems with the UPS, call your Local Distributor or the Help Desk at one of the following telephone numbers and ask for a UPS technical representative.
Two-Year Limited Warranty Two-Year Limited Warranty Powerware Models 5115 and 5125 WARRANTOR: The warrantor for the limited warranties set forth herein is Powerware Corporation, a Delaware Corporation (“Powerware”). LIMITED WARRANTY: This limited warranty (this “Warranty”) applies only to the original end-user (the “End-User”) of any Powerware 5115 and 5125 Products (individually and collectively, the “Product”) purchased on or after June 1, 2004 and cannot be transferred.
Two-Year Limited Warranty WHAT THIS LIMITED WARRANTY DOES NOT COVER: This Warranty does not cover any defects or damages caused by: (a) failure to properly store the Product before installation, including the charge of batteries no later than the date indicated on the packaging; (b) shipping and delivery of the Product if shipping is FOB Factory; (c) neglect, accident, abuse, misuse, misapplication, or incorrect installation; (d) repair or alteration not authorized in writing by Powerware personnel or perf
Extended Ten-Year Pro-Rated Limited Warranty Extended Ten-Year Pro-Rated Limited Warranty Powerware Models 5115, 5125, 9104, 9120, 9125, 9170, and FERRUPS WARRANTOR: The warrantor for the limited warranties set forth herein is Powerware Corporation, a Delaware Corporation (“Powerware”).
ExtendedTen-YearPro-RatedLimitedWarranty Powerware shall not be responsible for any charges for testing, checking, removal or installation of Warranted Items. THIS WARRANTY IS THE END-USER’S SOLE REMEDY AND IS EXPRESSLY IN LIEU OF, AND THERE ARE NO OTHER, EXPRESSED OR IMPLIED GUARANTEES OR WARRANTIES (INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PURPOSE, WHICH ARE EXPRESSLY DISCLAIMED).
Extended Ten-Year Pro-Rated Limited Warranty 48 Powerware® 5115 Tower UPS (500–1400 VA) User’s Guide S 05146640 Rev C www.powerware.
