▶Contact us Zhongshan Easyguard Electronics Co.,ltd Add: 2nd floor, building 3, No 77 caihong Road, West district, Zhongshan city, Guangdong, China Phone: 86-760-22113597 Web: www.ieasyguard.com Email: sales@ieasyguard.com Important: This device can improve the vehicle safety level, but could not prevent the vehicle from stolen or the occurrence of unexpected accidents. EASYGUARD Electronics will not be liable for any resulting from the damage of this product cause by direct or indirect losses.
INDEX Safety warning -------------------------------------------------------------------------------------------------------------------------1 Installation guide 1.Before starting the installation ------------------------------------------------------------------------------------------------2-3 2.DIP switch setting on control module ------------------------------------------------------------------------------------------3 3.
Dear Customer, (1) Never remote start the vehicle with the vehicle in gear, and. Thank you for purchasing our EASYGUARD EC002 series PKE car alarm with push start stop button. This alarm is combine with latest PKE (passive keyless entry) technology, remote engine start, keyless go and touch password entry backup function. Please read the user manual and wire diagram carefully before you start installation. Once the alarm is properly installed, it can improve the safety of your vehicle greatly.
Important: 3.Deciding on components locations Only start installation when you receive all the accessories. Control module If there is missing any parts, please stop installation immediately and contact your vendor right away for the replacement. Some things to remember about where to mount the control module: 2. DIP Switch Setting on Control Module Please set the DIP switch on the control module to fit for your vehicle.
PKE antenna PKE antenna mount position Position B is the most common and widely used one. There are 2 PKE antennas Position A 2.9M PKE antenna 2.9M PKE antenna 4M PKE antenna 5M PKE antenna Position C Position B 2.9M PKE antenna 2.9M PKE antenna 4M PKE antenna 4M PKE antenna Warning: All the antennas are fragile and easy to break, please handle with care when mount them or plug/ unplug them.Please do not pull the antenna to avoid the wires break off.
SE 0L 30 3M SE 3M E 0L 30 3M SE 0L 30 300 3M LS 300 3M SE 0 0L C 8 SE 0L LS 7 LED2 1 2 3 4 5 6 7 8 9 C 0 30 30 9 300 LS LS 3 E 00 M3 300 LS 3M E E 3M E Face 3M E 3M 3M E LS SE 0L LED1 SE LS 300 300 30 0L 300 3M Back P4 3M E P5 3M LS P3 30 E LS 300 P3: The shorter PKE antenna mount position P3: Inside of middle upper of the front windshield in the car 3M 300 E LS Installation for password keypad 3M Once finish mount the PKE ante
Main wire harness introduction IMPORTANT: 1.6-Pin ignition wire harness If your kit is with 3 color GWR wire, then there is no shock sensor, vice versa.
Unlocking wire, see central door locking installation Orange/black See central door locking installation Yellow See central door locking installation White Locking wire, see central door locking installation Orange See central door locking installation Pink Output of factory horn(-) Green wire For GPS module, not used, insulate separately Note 13 Wiring method of negative (-) trigger of the trunk 15A 15A, see note 16 Purple wire -300mA, see note 17 1 2 3 4 5 6 White/black The 2nd row 10 p
Note 16 Some things to remember about mounting the siren: Window closer module wire connection with Ec002 Keep it away from heat sources, such as radiators, exhaust manifolds, turbo-chargers, and heat shields. If there is window closer module has a wire need to connect with EC002, please connect the white locking wire in central door locking with the wire from the window closer module. Mount it where a thief cannot easily disconnect it, whether the hood is open or shut.
P1 style engine start button P4 style engine start button Ø 38mm 47mm The outer rubber is detachable. Ø56mm Ø10mm Ø 27.5mm Button thickness is 10mm Ø 41mm P1 button size: Ø56x10mm(with rubber), Ø 41x10mm(no rubber), P2 style engine start button The ring is detachable Ø 27.5mm Ø52mm P5 style engine start button P1 button size: Ø 41x10mm(no rubber) Ø 52x10mm(with rubber) The outer rubber ring is detachable.
Engine start button color changes for different operation Engine start button style When armed Turn off P1 Turn off P2 P3 Turn off P4 Turn off P5 Turn off P7n Turn off When disarm blue blue red red blue red Turn on ACC blue blue red red blue red Turn on ON Stepping On foot brake pedal blue Blinks blue color blue Blinks blue color red Blinks red color red Blinks red color blue Blinks blue color red Blinks red color When started engine green red red red When engi
Arm/Panic mode 1.Lock/Arm: press lock button function) once(turn off PKE 2.Unlock/disarm: press unlock button PKE function) Disarm Start button/ trunk release 4.Don’t put the remote control together with the metal keys or avoid damage or signal shielding. 5.Don’t put the remote control with cell phone or other products will emit strong signal to avoid the signal once(turn on 3.Remote engine start: In arm status, keep pressing the start button for around 3 seconds.
Method 2: Use a screw driver and push it into the hole of the ignition cylinder (see photo on the left), turn the ignition key to ACC position, then pull out the key with force will take out the ignition cylinder.Then remove wires from ignition switch and put the push start button over the empty key cylinder slot. push here then pull out the cylinder Important: Only a qualified staff can do this as there is risk to lock the steering lock again if the operation is not correct.
Central Door Locking Wire Connection Checking your locking system Please use a diode test lamp (voltmeter) for checking electric currents. Conventional test lamps conduct too high voltage will cause damages to electronic control device. Please take care not to connect the Note: The most common type of door lock systems are Type A positive trigger, Type B negative trigger and Type C reverse Polarity. Other Types D to type H probably require external relays when do the installations.
NC Lock COM NO NC Unlock COM NO Orange NOT USED-Don’t connect (insulate separately) White (Lock signal) Yellow +12V(vehicle fused +12V constant) NC FACTORY LOCK SWITCH LOCK Orange/black NOT USED-Don’t connect (insulate separately) (Unlock signal) Yellow/black +12V(vehicle fused +12V constant) COM UNLOCK NO +12V L White/black Lock UL NC Unlock COM NO Drivers door White (Lock signal) +12V Yellow UL +12V (vehicle fused constant +12V) Orange/black White/black Yellow/black (Unlo
Type E: Electrically-activated vacuum systems. Polarity reverses on a single wire to lock and unlock. Please set the door lock/unlock time to 3.5 seconds. NC The vehicle must have a vacuum actuator in each door. Making sure that locking the doors from the driver’s or passenger side using the key activates all the actuators in the vehicle. This requires a slight modification to the door lock wire harness. Lock COM NO The door locks are controlled by an electrically activated vacuum pump.
NC Lock COM NO NC Unlock COM NO Orange not used (insulate separately) White (Lock signal) Yellow Lock resistor (if required) NC Lock +12V (vehicle fused constant +12V) Orange/black NO not used (insulate separately) Unlock resistor Drivers door (if required) White/black Yellow/black (Unlock signal) +12V (vehicle fused constant +12V) COM NC Unlock COM Door lock switch key cylinder NO Orange not used (insulate separately) White (Lock signal) Yellow Chassis Ground Orange/black not
Wiring Diagram of EASYGUARD EC002 Yellow wire 3 color wire (see Note 8) or shock sensor (see note 9) Note 8: If the alarm equip with 3 color wire, which is used to connect with immobilizer bypass wire or GWR status wire or status output wire Choose one method as below: No need to connect orange wire for all below method: Method 1: Cut off the car factory chip immobilizer wire into 2 parts, each end connect with the white & yellow wire respectively; Method 2: If there is GWR (-) wire, connect the GWR(-) wire
Function description: D.Remote engine start for back up purpose: ENGINE START STOP For some special situation such as there is no brake signal or the brake fuse was failed to work, user can use remote engine start function to start the vehicle, method is keep pressing start button on key fob for 3 seconds will remote start the vehicle, and once the vehicle is started, user keep pressing start button for 3 seconds will cut off the vehicle engine.
8. To enable or disable PKE feature (PKE ON/OFF setting) To disable PKE feature(valet mode): Started the vehicle, stepping on foot brake pedal, keep pressing lock & unlock button on key fob at the same time for 5 seconds, siren beeps 5 times and turn signal light flashes 5 times. The alarm is enter into car valet mode & disable the PKE feature.
Color changes with different operation on the password keypad 11.Anti-hijacking The alarm default is turn on anti-hijacking function with Switch 4 on control module is press down. Once anti-hijacking function is turn on, when the vehicle is running, user get off the vehicle then close the door well and take the remote control away.
7.If you use password entry function to unlock the vehicle but not open and close the vehicle door in 15 seconds, the door will be re-lock automatically after 15 seconds. 8.If you unlock car door by password and open but forget to close the door, the siren will beep for every 5 seconds to remind you to close the door well. b.Use touch password to lock the vehicle: 1.Stop the vehicle and close the door well, user stand outside the vehicle and input C0#+6 digital password in turn.
.Vibration alarm(optional) 4.Starting time( Cranking time) prolong setting The vehicle default is without shock sensor and has no vibration alarm function. User can choose to equip with shock sensor version. Do not step on foot brake, press start button on the remote control once, siren beeps twice, means starting time is prolong 0.5 seconds and become 1.3 seconds( default starting time is 0.
3.If I forget the password I set, how to re-set it again? Please refer to d.password reset instructions on page 39-40 in user manual. 4.When I attempt to start the car, it start but shut off a few seconds, what’s the reason? There are possible 4 reasons: A.The blue fuel pump wire in 20 Pin wire harness not connect well which lead to there is no electricity when you want to start the vehicle.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.