EDC211D Features EDC211D-A EDC211D-B ■ The shell is made of flame-retardant materials, with a fire rating of V-0; ■ Patented antenna design, super anti-interference; digital radar chip, good consistency; ■ Not affected by temperature, humidity, airflow, dust, noise, brightness, etc.; ■ The batch meets the requirements of EN300440 and EN301489 standards; ■ Meet environmental protection requirements.
EDC211D Typical application products EDC211D typical application Ceiling light Panel Light Three anti-light High bay lights *The above are typical application products, and more products can be expanded Electrical properties Transmit frequency 5.8GHz±15MHz Load power <400W @100V-240V Operating Voltage AC 100-240V EDC211D-A/EDC211D-B 3db beam angle 93°(XZ plane) 99°(YZ plane) Standby power consumption <0.5W Sensing distance 3.
EDC211D Pin description Pin L-out N-out L-in N-in EDC211D-A Pin Description Fire wire out Zero line out Fire wire in Zero line in Pin L-out N-out L-in N-in EDC211D-B Pin Description Fire wire out Zero line out Fire wire in Zero line in -3Address: Room 601, Building A2, Hangcheng Industrial Zone, Chentian, Xixiang Street, Baoan District, Shenzhen Tel: 0755-2778-8421 Website: http://www.easydetek.
EDC211D DIP switch settings First place: Sensing distance setting 1 100% ON 50% According to different applications, the sensing distance can be adjusted by the code switch to set 100%, 50% Second and third digits: delay time setting 2 3 5s ON ON 1min ON 3min 0N 5min Delay time refers to the time that the light is on after the moving object leaves the sensing area.
EDC211D Infrared remote control settings 100%: the farthest distance 75%: farther away 50%: closer 25%: short distance 10s: select time 10s 30s: select the time 30s 1min: select time 1min Turn on the photosensitive function Turn off the photosensitive function 30Lux 15Lux Product size chart EDC211D-A unit:(mm) -5Address: Room 601, Building A2, Hangcheng Industrial Zone, Chentian, Xixiang Street, Baoan District, Shenzhen Tel: 0755-2778-8421 Website: http://www.easydetek.
EDC211D EDC211D-B unit: (mm) Function Description Photosensitive function is on When the ambient light is bright enough, the light will not automatically light up even if a moving object is detected After the moving object leaves, the sensor will enter the When the ambient light is lower than the preset photosensitive threshold, the light will automatically light up when the sensor detects a moving object After the preset delay time, the light will automatically turn off delay time when it cannot det
EDC211D Photosensitive function is off No moving objects can be detected, and the lamp goes out When the sensor detects a moving object, the light automatically lights up at 100% brightness and enters the set delay time After the delay time, when the sensor cannot detect any moving objects, the lamp will be off Packaging Information Support packaging: Blister packaging Bubble bag packaging PE bag packaging -7Address: Room 601, Building A2, Hangcheng Industrial Zone, Chentian, Xixiang Street, Bao
EDC211D Detection diagram *Note: The distance can be adjusted according to the actual application -8Address: Room 601, Building A2, Hangcheng Industrial Zone, Chentian, Xixiang Street, Baoan District, Shenzhen Tel: 0755-2778-8421 Website: http://www.easydetek.
EDC211D Precautions 1. The installation process of the product requires keeping the antenna board at a certain height away from the metal plane, and not close to or touching the metal plane, otherwise the product may not work normally! 2. Avoid installing metal accessories or shells. Metal will block microwaves and affect the effect; therefore, this product should not be installed in a metal shell. However, the penetration effect is better for obstacles such as plastic, ceramic, and wood soil; 3.
EDC211D Configuration version description 【hardware】: 【software】: - 10 Address: Room 601, Building A2, Hangcheng Industrial Zone, Chentian, Xixiang Street, Baoan District, Shenzhen Tel: 0755-2778-8421 Website: http://www.easydetek.
EDC211D Federal Communications Commission (FCC) Compliance Statement for USA This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.