Instructions Manual

ManualsBrandsEASTPARTS INTERNATIONAL ManualsElectronicsSMART DIRECT TRAINER

Contact

Made in Japan

If you have any trouble with this product or request for maintenance, refer the attached "Minoura

Limimted Warranty Policy" card first, then contact the shop you originally purchased this

product or the distributor in your country. The distributor list is found on our web site.

(ver.1.0 2019/2)

Merit of Direct Drive

LSD9200 "Kagura" Direct-Drive works with your current bike frame when you remove your

wheel and mount your frame directly to the unit. Direct-Drive eliminates any potential power loss

from traditional trainers because there is no chance of tire slippage and it transmits all the power

you generate to the electric motor.

The precisely tuned resistance unit eliminates all the noise and vibrations usually associated with

indoor trainers and provides a very smooth and quiet training session anytime.

Instructions Manual

Direct Drive Bicycle Trainer

(Sprocket gear is sold separately)

Compatibility

Kagura-DD is compatible with Shimano and SRAM 8s, 9s, 10s and 11s. Campagnolo is currently

NOT supported. You need to prepare the rear sprocket gear that fits your bike component

separately.

The AC Adapter is capable with worldwide voltage 100V – 240V, but the electric plug design

must fit your country's regulation. If you need to change the plug that came with your trainer, it

is available as an option for purchase.

We strongly recommend visiting the

Minoura website regularly to check for

updates to the Kagura rmware.

For more info, check out ...

http://www.minoura.jp/english/trainer/smartturbo/

lsd9200.html

and click "Firmware Updates" button.

MINOURA North American Tech Center MINOURA Japan Headquraters

(for U.S. residents ONLY)

(for ALL customers)

Hayward, California, U.S.A. 134-1 Shimomiya, God, Anpachi, Gifu 503-2312 Japan

Phone: 1-510-538-8599 (8 am - 5 pm, Mon - Fri, PST) Fax: +81-584-27-7505

Fax: 1-510-538-5899 Email: minoura@minoura.jp

Email: support@minourausa.com Web: www.minoura.jp

Summary of content (12 pages)

PAGE 1
Direct Drive Bicycle Trainer Instructions Manual (ver.1.0 2019/2) We strongly recommend visiting the Minoura website regularly to check for updates to the Kagura firmware. For more info, check out ... http://www.minoura.jp/english/trainer/smartturbo/ lsd9200.html and click "Firmware Updates" button. (Sprocket gear is sold separately) Merit of Direct Drive LSD9200 "Kagura" Direct-Drive works with your current bike frame when you remove your wheel and mount your frame directly to the unit.
PAGE 2
Important Notes Read Carefully Before Use • Compatible only with the rear wheel hub width 130 & 135mm in 9mm Quick Release system, or 142 & 148mm in 12mm Thru Axle system. Any other sizes or systems cannot be used. • Compatible with Shimano and SRAM 8s, 9s, 10s and 11s gears. Some Campagnolo gears are not be compatible. The sprocket gear doesn't come in the kit so you need to prepare it separately.
PAGE 3
LSD9200 Contents Flywheel Drive Belt [LSD9200 Main Body] [Step-Bar] Step-Bar Body Foot Adjuster Carrying Handle Power Cable (shown is A-type plug) [Electric Power Supply] AC Adapter (100V – 240V) Foot Adjuster [Supplied Parts] Spacer Ring for 10s (*1) Quick Release Skewer Knob Bolt (Large) Leftside End Plug for 12mm Thru Axle Round Collar (*2) Knob Bolt (Small) Leftside End Plug for 9mm Q/R Rightside End Plug for 12mm Thru Axle Round Collar (*2) (*1 You will use on 8s and 9s too) (*2 Same siz
PAGE 4
How To Install Step-Bar Required Tool : Nothing Step-Bar (direction is specified) Knob Bolt (Large) + M8 Flat Washer Round Collar Round Collar Knob Bolt (Small) + M6 Flat Washer 1 (Fig. A) Install the Step-Bar to the Body. (Fig. A) Put the Knob Bolt (Large) with the Round Collar into the plain hole on the Step-Bar, and screw it into the thread hole on the Body. ! The direction of the Step-Bar is specified. You cannot install it in the wrong direction.
PAGE 5
3 Turn the Step-Bar 90 degrees, set it on the grooves on the bracket, and tighten the larger Knob Bolt to hold. (Fig. D) The smaller Knob Bolt can be stored in the thread hole on the Step-Bar. Now the Kagura-DD is ready to be stored in the narrow area such as under the bed. (Fig. D) How To Install Sprocket Gear Required Tools (Fig.
PAGE 6
How To Replace To 12mm Thru Axle The original hub on your Kagura-DD is preset for the standard 9mm Q/R. If your bike is equipped with 12mm thru axle system, you must replace the right side hub end with the supplied special plug. (Fig. H) (Fig. H) Hub end for standard 9mm Q/R system 1 Hub end for 12mm Thru Axle Apply the wrench to the original right side end plug, and turn it counter-clockwise to remove while holding the flywheel with your other hand. (Fig. I) (Fig.
PAGE 7
How To Remove Sprocket Gear To remove the sprocket gear, you need a special tool called a Sprocket Remover together with the Lock Ring Tool. Sprocket Remover Set the chain of the Sprocket Remover to the largest gear on the sprocket. It means that turning the Lock Ring counterclockwise will move the sprocket gear together in the same direction, so you need to hold it by this tool. Fully insert the Lock Ring Tool into the Lock Ring, and apply the wrench to the tool.
PAGE 8
How To Mount a Bike on Your Kagura-DD 1 Fully open the Quick Release Skewer lever. 2 In order to make mounting the bike easier, set the rear derailleur to the top. 3 As same as installing the rear wheel onto the bike, hook the chain on the top gear, then set the bike frame on Kagura-DD gently. (Fig. O) 4 Make sure the bike frame has been set stable and vertical, close the skewer lever to hold. Adjust the skewer nut tightening correctly before closing the lever for your safety if necessary. (Fig.
PAGE 9
12mm Thru Axle System About The Direction of The Leftside End Plug Compatible with the rear end width in 142mm and 148mm only. 142mm Change the direction of the Leftside End Plug to the hub as shown in Fig. Q. 148mm 142mm : Face the wider sleeve side inward. 148mm : Face the narrower sleeve side inward. (Fig. Q) How To Install 12mm Thru Axle and How To Mount Your Bike 1 Insert the supplied Leftside End Plug for 12mm Thru Axle into the left side of the hub. (Fig.
PAGE 10
Turning Power On and Checking Status Insert the round shape Power Plug to the connecting port on Kagura-DD, and plug in to the electric outlet, then the power will turn ON automatically. (Fig. S) To turn off the power, simply pull out the plug. ! ! Be careful to keep the cord away from anything it can become snagged or catch on. Undue pressure on the cord can pull the internal circuit board out of position and cause the unit to malfunction. Connect the supplied AC adapter only.
PAGE 11
If Your Unit Doesn't Work http://www.minoura.jp/data/trainer/smartturbo/firmware-update-instructions-2-jp.pdf The first step in trouble shooting your unit is to make sure you are using the most current version of our firmware. Update your firmware by going to the link posted above. To get this service, you must be registered to Minoura as an official user.
PAGE 12
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.