3 Troubleshooting Correcting Errors Occasionally errors (malfunctions), such as film jams, may occur in the imager during print operations. You can easily correct minor problems. If more serious malfunctions occur, you should contact a trained Authorized Service Provider of Kodak products (see “Calling for Support” on page 3-17). Error and Alarm Indications The Imager can detect malfunctions and other conditions that require operator action.
Troubleshooting Error Message Screen The Error Message screen is the main error reporting mechanism for the Imager. When the Imager detects an error, an alarm sounds and the Local Panel displays an Error Message screen that describes the error and gives a corrective action. Touch anywhere on the screen to silence the alarm. 1 6 5 2 4 3 Error Message Screen Error Message Screen Details 3-2 1 Error Code. Identifies the type of error. Refer to this code when calling for service.
Troubleshooting NOTE: If you close an Error Message screen without correcting the current error, you can recall the Error Message from the Current Errors screen. (See “Current Errors Screen” on page 3-4.) Operator Action September 30, 2004 When an error message is displayed: 1. Silence the alarm by touching anywhere on the Error Message screen. 2. Perform the corrective action recommended on the screen. If this does not clear the error, call for service. (See “Calling for Support” on page 3-17.
Troubleshooting Current Errors Screen The Current Errors screen shows a list of uncorrected errors in the Imager. To display this screen: 1. Press the Menu button. 2. On the Main Menu screen, press Current Errors. The Current Errors screen appears: List of Errors Current Errors Screen To see detailed information about any of the errors: 1. Highlight the error using the Up or Down arrow. 2. Touch Select. The Error Message screen displays the error message for the error you selected.
Troubleshooting Current Errors Notice on the When there are one or more uncorrected errors in the Imager, the Home Home Screen screen displays a Current Errors notice that shows the number of uncorrected errors in the Imager. To see a list of the current errors, you can display the Current Errors screen. (See “Current Errors Screen” on page 3-4.
Troubleshooting Calibration Failure Periodically the Imager must be calibrated to ensure that internal settings match the characteristics of the film in the Imager. Calibration is performed by running a calibration print. The Imager runs a calibration print when: • A film cartridge containing film with new sensitometric characteristics (speed, contrast) is loaded. • The Imager has not printed film for 7 days. • The Dpatch (density patch) printed on the film is out of range.
Troubleshooting These two calibration errors indicate a major machine or film fault. The Imager cannot continue to operate with the current film. If you cannot restore normal operation by following the recommended action on the error message screen, call for service. (See “Calling for Support” on page 3-17.
Troubleshooting Film Transport Problems The illustration below shows the path that film travels through the Imager after the operator requests a print.
Troubleshooting Films may occasionally jam at various points along the film path. When a film jam or film feed error occurs, an error message appears. The error message identifies the area where a jam has occurred and recommends a corrective action. The following information supplements the advice given in the error messages for film feed problems. Manually Closing the Film Cartridge When clearing film jams you may have to close the film cartridge manually.
Troubleshooting 3. Clear any films that may be jammed in the film cartridge area. 4. Turn the rollback knob counterclockwise to close the cartridge. Film Pickup Problems in Area 1 Area 1 is the location where film is removed from the film cartridge and positioned to be sent by drive rollers toward the exposure area. If the Imager cannot properly pick up a sheet of film and position it for drive, error 21-116 (Pickup Fail) is declared. Error 21-177 (Cartridge Failed to Close) also relates to Area 1.
Troubleshooting Removing Film Jams from Area 2 Area 2 in the Imager includes the path between the film pickup assembly and the exposure platen. NOTE: When jams occur in Area 2, the film cartridge is left open. When you open the front door, the top sheets of film in the cartridge will be exposed. Before opening the door, make the room as dark as possible to minimize exposure. Rollback Knob Film Pickup Assembly Area 2 Exposure Platen H200_0006da Jam Area 2 1.
Troubleshooting Removing Film Jams from Area 3 Area 3 includes the exposure platen. Jams in this area occur as film is entering the platen before exposure, or as film is leaving the platen after exposure. In rare cases, film may stall in the transport area above the platen. Plastic Thumb Tab 2 Vertical Transport Platen Feed Rollers Platen Door Latch Area 3 Exposure Platen Plastic Thumb Tab 1 H200_0007da Jam Area 3 1. Open the front door. NOTE: When film jams in this area, the cartridge may not close.
Troubleshooting b. Push the optics module toward the rear of the imager slowly and smoothly. Optics Module 10 cm (4 in.) c. Clear the film from inside the platen. If film is caught in the platen feed rollers, pull Plastic Thumb Tab 1 (inside the platen door) to the right. This opens the rollers and frees the film. d. After clearing the jam, close the platen door. 5. If film is stalled in the vertical transport area, pull Plastic Thumb Tab 2 in this area to the right to open the rollers and free the film.
Troubleshooting Removing Film Jams from Area 4 Area 4 includes the film processor. When a jam occurs in this area all films in the Imager must be removed. Processor Drum Area 4 Plastic Thumb Tab H200_0008da Jam Area 4 1. Open the hood. CAUTION: Drum and rollers inside the processor are hot. Exercise caution when removing jammed film from the processor. 2. Release the two clamps at the left of the processor and open the drum cover. (See the following figure).
Troubleshooting Open Drum Cover Open Clamps Plastic Thumb Tab Opening the Drum Cover 3. Clear the jammed film from the processor area (there may be more than one sheet). If film is jammed in the drive rollers, pull the Plastic Thumb Tab to the left to open the rollers and free the film. 4. Close the drum cover and secure it with the two clamps. 5. Remove any films in Area 5. (See page 3-16.) 6. Open the front door. 7. Remove all films in the lower part of the Imager. 8. Close the front door. 9.
Troubleshooting Removing Film jams from Area 5 Area 5 consists of the components between the processor drum and the film exit tray. Jams can occur in this area between the drum and the densitometer, or in the densitometer. See the figure below. When a jam occurs in this area all films in the imager must be removed. Exit Tray Plastic Thumb Tabs Processor Drum Densitometer Area 5 H200_0009da Jam Area 5 1. Open the hood. CAUTION: Drum and rollers inside the processor are hot.
Troubleshooting 3. 4. 5. 6. 7. Remove any films in the processor. (See page 3-14.) Close the hood. Open the front door. Remove all films in the lower part of the Imager. Close the front door. The processor will have to warm to operating temperature before the imager can resume printing. Calling for Support If you cannot correct a malfunction and need help, call for support (see the following table).
Troubleshooting Service Phone Numbers Country Phone Number Czech Republic 420 236 100 307 420 62 335 426 Denmark 45 70206129 Finland 35.88001214 France 01 4001 4705 Germany 49.0180.3000.307 India 1600 118989 Iran 00 98 216 950821 00 98 216 402105 00 98 21 256 9741 00 98 21 256 9097 Ireland 44.01442 845775 Israel 00 972 3 9254040 Italy 39.02.66028000 Japan 0120-45-1881 3-18 Jordan 00 962 6 4545845 00 962 6 4543354 Netherlands 31.347.363900 Norway 47.
Troubleshooting Service Phone Numbers September 30, 2004 Country Phone Number Romania 00 40 1210 3854 Saudi Arabia 00 966 2 682 8219 00 966 1 464 5064 Spain 902 19 03 99 Sweden 46.200.119.494 Switzerland 41.0800.
Blank Page
4 Adding a Modality After the Imager has been placed into service, you can later configure the Imager to print images from additional modalities. The Imager is capable of receiving images from twelve DICOM-compatible modalities concurrently. Adding a modality involves adjusting some of the image quality settings in the Imager to match the new modality. The following procedure explains how to add one new modality. NOTE: You must have the Service Passcode to perform this procedure.
Adding a Modality Modality-Related Parameters The Imager must be configured to print from each connected modality. In the Imager a set of modality-specific parameters must be created for each modality that will print to the Imager. For many modalities, the required parameters can be taken from the "Modality Preferences Database" (MPDB). This internal database, within the Imager, contains tested parameter sets for many commonly used modalities.
Adding a Modality Configuration Procedure The modality setup procedure is performed on the Imager Local Panel. 1. Be sure that the proper film size and type required for the modality is loaded in the Imager. 2. Start from the Home screen. 3. Press Menu. 4. Touch Setup Imager.
Adding a Modality 5. Select Modality (SCU) config. 6. Enter the Service User ID (99) and the Service Passcode on the keypads that appear. Previously Configured Modalities NOTE: If the new modality has previously printed to the Imager but has not been configured, it will appear on the above list but without a footprint symbol. 7. Send an Image from the new modality to the Imager. • If this is the first time the new modality has printed to the Imager, continue with step 8.
Adding a Modality 8. Wait for the following message screen to appear - about 1 minute. (When a modality prints to the Imager for the first time, this message will appear.) NOTE: If this message does not appear, the modality may not be properly set up to print to the Imager. Check the modality setup and re-send the image. IP Address of the modality that has printed to the Imager 9. Touch OK. The modality that sent the image should now appear at the bottom of the list of modalities.
Adding a Modality 10. Wait for the Imager to print the image sent from the modality. • The imager will attempt to find an appropriate set of parameters for the modality in its internal database of modality parameters. • If no parameter set is found for the modality, the Imager uses a universal set of parameters to print the test image. 11. Examine the quality of the print. Determine if it is acceptable. 12. On the Select Modality screen (page 4-4), select the modality that printed the image. 13.
Adding a Modality 14. Touch Yes. 15. Select the name of the modality manufacturer.
Adding a Modality 16. Select the modality type. 17. Select Model. • The Imager searches the parameter database: – If an appropriate set of parameters is found, these parameters will be applied to all images printed from this modality. – If no parameter set is found for the modality, a universal set of image quality parameters is assigned to the modality. You will probably have to modify some of these parameters to achieve satisfactory image quality. • The Modality defaults screen appears.
Adding a Modality 18. 19. 20. 21. Send another clinical image from the modality to the Imager. Wait for the Imager to print. Examine the quality of the print. Is the quality of the test print acceptable? • Yes - Go to “Changing the Modality ID” on page 4-10. • No - You can change image quality by adjusting individual image quality parameters: a. Select Image quality on the Modality defaults screen. b. If the above information screen appears, Touch [X]. The Image Quality screen appears.
Adding a Modality c. Go to Section 5 of this manual to adjust the parameters shown on the Image Quality screen. d. After completing the procedure in Section 5, continue with “Changing the Modality ID”. Changing the Modality ID The Modality ID sent down from the modality is a combination of modality type and IP Address. If you wish, you can change this "name" to a more user- friendly name for use on the Local Panel Screens as follows: 1. With Modality ID highlighted, touch Select.
Adding a Modality Setting the Advanced Parameters NOTE: The Imager automatically sets the Advanced default parameters for a modality when you begin the modality setup process. In most cases these settings are satisfactory. Do not change these parameters unless you are certain that your application of the modality requires different settings. 1. Return to the Modality defaults screen. 2. Select Advanced. A list of "Advanced" parameters with their currently selected default values appears.
Adding a Modality Selecting Film Size The film sizes accepted by the Imager are 14 by 17 in., 11 by 14 in., and 14 by 14 in. If the default size shown on the screen is not the desired size, change it. 1. On the Advanced defaults screen, highlight Film Size. 2. Use the Select button to choose the film size appropriate for this modality. Each time you touch Select, the film size will change. 3. For most installations Override modality should be left at false.
Adding a Modality Selecting Film Type The Film Type choices are DVB (DryView Blue) and DVC (DryView Clear). There is more than one type of Kodak DryView DVB film. The DVB choice applies to all DVB and DVB+ film types. If the default shown is not correct for this modality, change the value as follows 1. On the Advanced defaults screen, highlight Film Type. 2. Touch Select. The Edit DICOM attribute screen appears. 3. Use the Select button to choose the type of film appropriate for this modality. 4.
Adding a Modality Selecting the Type of Image Resizing If the image sent down from the modality is too large for the size of film installed in the Imager, the Imager can resize the image to fit on the film by either of two methods: • Minify - To reduce the image to fit on the selected film size. • Crop - To remove the edges of the image to allow it to fit on the selected page size. For more information on these two methods, refer to “Image Resizing” on page 2-45. 1.
Adding a Modality 4. For most installations Override modality should be left at false. NOTE: If you select True for Override modality, the Image Resizing mode set in step 3 will take precedence over any type of sizing requested by the modality. 5. Touch the Back arrow to return to the Advanced defaults screen. Selecting Print Priority September 30, 2004 The Priority for prints determines the order in which the Imager will process prints if a number of modalities are requesting prints at the same time.
Adding a Modality 3. Use the Select button to choose the desired priority for printing. 4. For most installations Override modality should be left at false. NOTE: If you select True for Override modality, the priority set in step 3 will take precedence over any priority requested by the modality. 5. Touch the Back arrow to return to the Advanced defaults screen.
Adding a Modality Selecting N_Event Reporting "N_Events" are status changes at the Imager, such as changes from "ready" to "busy." The Imager can be configured to report these status changes to the modality as they changes occur. CAUTION: This feature can cause a serious malfunction in the modality if it is not designed or configured to accept N_Event messages. Leave the N_Event reporting attribute set to false unless you are certain the modality can accept N_Event messages. 1.
Adding a Modality Selecting Report Warnings "Warnings" are messages from the Imager indicating a non-fatal problem in the Imager. Like "N_Events," these can be sent to the modality if desired, but they should not be if they can cause problems at the modality. 1. On the Advanced Defaults screen, highlight Report Warnings. 2. Use the Select button to choose Yes or No.
Adding a Modality Selecting Color Negotiation The Imager prints only grayscale images. If a modality has color capability and a request to print a color image is sent to the Imager, the Imager software can print a grayscale version of the color image. 1. Touch the Down arrow to proceed to the second Advanced defaults screen. 2. Use the Select button to choose No. NOTE: If you select No, the Imager will not accept color prints from the modality.
Adding a Modality Setting up the Text (Annotation) Box This parameter allows you to select items to be printed in a "text box" on the bottom of each sheet of film. 1. Select Film Text to display the items you can select. 2. Select Hospital name if you wish to include the name of your hospital in the annotation box. A check will display adjacent to the field. a. Select (Edit Hospital name) and touch OK. b.Use the keypad to enter the name. c. Touch OK. 3. Select any or all of the other items on the screen.
Adding a Modality Saving the Modality (SCU) Parameters 1. Select Save Changes to save the parameter changes you have made. 2. Touch OK. 3. Touch the Back arrow twice to return to the Setup Imager screen.
Adding a Modality Backing up the Configuration The configuration parameters must be backed up (recorded) on a floppy diskette so they can be restored if the Imager software is updated. You will need a blank 3.5-inch floppy diskette, 1.44 mb, IBM format. 1. Start from the Setup Imager screen. 2. Select Backup Configuration. 3. Touch Yes.
Adding a Modality 4. Touch OK. 5. Choose an easy-to-remember file name for the backup file. For example, a:\09_15_04.bin or a:\backup1.bin. The prefix a:\ and suffix .bin are required. 6. Write down the filename. 7. Enter the filename on the keypad and touch OK on the keypad.
Adding a Modality 8. Touch Yes. 9. Wait for the front door to open.
Adding a Modality The Imager first closes the film cartridge and then unlatches the door. This takes about 30 seconds. Front Door Computer Access Door H200_0034DAA 10. Open the computer access door. 11. Insert a blank diskette into the floppy disk drive. The Imager records a backup file of the configuration parameters on the diskette.
Adding a Modality 12. Touch OK. 13. Remove the floppy disk from the computer. 14. On the disk label, write the filename exactly as you entered in step 7. Include the date of the backup. 15. Store the floppy disk in a safe place. It may be required if the Imager is serviced. 16. Close the computer access door and the Imager front door. 17. Log out of the Service Passcode: a. Touch the Back arrow to return to the Main Menu. b.Touch System Functions. c. Touch Log off and then Touch OK.
Adding a Modality 18. Press the Back arrow. The Home screen should appear. Configuration of the new modality is now complete.
Blank Page
5 Optimizing Image Quality Image Quality Parameters If the quality of an image printed by the Imager is not acceptable, you will have to enter new values for the parameters shown on the "Image quality" screen. This section provides basic information that will help you select and enter values for these parameters that are appropriate to the type of modality that sent the image. The Advanced Parameters are "Polarity" and "Smoothing Type.
Optimizing Image Quality • Advanced - Includes two parameters: – Polarity - In general, indicates whether an image is black on a white background or the reverse. In this case, specifies whether the Imager will print images with the same polarity as the images sent from the modality (Positive), or the reverse (Negative). – Smoothing Type - A value (1 - 15) that specifies a level of smoothness/sharpness in transition between density differences.
Optimizing Image Quality 4. Choose the Image Density associated with the Table No. you chose. If there is a range of density values: • Choose the density value indicated in bold if there is one. • If there is no bold value, choose the middle value. For example, if the range is 2.7 to 3.1, choose 2.9. • If there are only 2 density values, choose either one. 5. Choose the Smoothing Type from Table 1. 6.
Optimizing Image Quality Table 1. Selection of Parameters by Modality Type Modality Type TFT Set Kodak and other CR (Computed Radiography) and DR (Digital Radiography) Systems. Also Workstations and imaging devices that output data to a linear-in- density contrast curve. WRKSTN2A.w87 Fuji CR CT (Computed Tomography) or MRI (Magnetic Resonance) 5-4 Table No. (Contrast Setting)* Image Density (Dmax)* Smoothing Type Note 1 2 3 4 3.1 3.0 2.9 2.
Optimizing Image Quality Table 1. Selection of Parameters by Modality Type Modality Type DSA (Digital Subtraction Radiography), including C-Arm and Digital Fluoro Phillips Medical Systems (PMS) EasyVision and other PMS modalities. September 30, 2004 TFT Set Table No. (Contrast Setting)* Image Density (Dmax)* Smoothing Type Note VER713C0.w87 (Alternative 1) 6, 7, 9 2.9 - 3.1 15 VER713C0 provides brighter image background than VER693C0. Lower Table numbers have less mid-tone contrast.
Optimizing Image Quality Table 1. Selection of Parameters by Modality Type Modality Type Nuclear Medicine Siemens Host Control or Workstation 5-6 TFT Set Table No. (Contrast Setting)* Image Density (Dmax)* Smoothing Type Note VER713C0.w87 (Alternative 1) 5 - 7 - 10 2.2, 2.3 12 Table 7 is popular. Table 5 has less mid-tone contrast and shows more isotope takeup. Table 10 has more mid-tone contrast and reduces takeup visibility on film. PMSV3K.w87 (Alternative 2) 10 - 14 2.2, 2.
Optimizing Image Quality Table 1. Selection of Parameters by Modality Type Modality Type Ultrasound TFT Set Table No. (Contrast Setting)* Image Density (Dmax)* Smoothing Type Note VER693C0.w87 (Alternative 1) 5 - 8 - 12 2.4 - 2.8 15 Table number choices vary with manufacturer and radiologist. Lower table numbers have less mid-tone contrast. Higher numbers have more. PMSV3K.w87 (Alternative 2) 7 - 10 - 13 2.4 - 2.8 15 Table number choices vary with manufacturer and radiologist.
Optimizing Image Quality Table 2. GSDF0 Dmax Setting versus Table Number (Contrast Setting) Density (Dmax) Table Number (Contrast) 1.7 1 1.8 2 1.9 3 2.0 4 2.1 5 2.2 6 2.3 7 2.4 8 2.5 9 2.6 10 2.7 11 2.8 12 2.9 13 3.0 14 3.1 15 Density and Table Number must be chosen in the pairs shown. NOTE: Some DICOM GSDF-modalities may direct the use of DICOM Presentation Look Up Tables (PLUTs) for some or all images.
Optimizing Image Quality GSDF-Compliant Modalities September 30, 2004 Use this procedure to select image quality parameters for GSDF-Compliant modalities that do not use PLUTs or use PLUTs for only some images. Write down the parameter values you select. a. Choose TFT Set GSDF0.w87 (used for all GSDF modalities). b. Refer to Table 1 (on page 5-4) and find the Modality Type for which the Imager is being configured. c. Choose Image Density. Choose the recommended density value in the Image Density column.
Optimizing Image Quality Entering the Image Quality Parameters 1. After choosing the parameter values for the modality, enter them from the Image quality screen. • Each choice on this screen calls up an entry screen for one of the parameters. • On some parameter entry screens an Override Modality option appears. The choices are True or False. For most installations you should select False.
Optimizing Image Quality 3. Select Save changes to save the changes you have made, and touch OK. 4. Send another image from the modality and check print quality. NOTE: For DICOM GSDF-compliant modalities, the printed images should approximately match images on DICOM GSDF-compliant displays. 5. Is the quality of the print acceptable? • Yes: Continue with“Setting the Advanced Parameters” on page 4-11. • No: Select Image Quality. 6. If an "Image Quality Help" screen appears, touch X. 7.
Optimizing Image Quality above the one you previously entered. 8. Enter and save the new Table number (steps 1 - 3). 9. Send another image from the modality and check print quality again. NOTE: You may have to try other Table numbers (and Densities) to achieve high quality prints. 10. When print quality is acceptable, return to “Changing the Modality ID” on page 4-10. 11. If you are unable to achieve satisfactory quality, call service for help. Refer to “Calling for Support” on page 3-17.
6 Specifications Dimensions Height: 117 cm (46 in.) - Top cover closed 158 cm (62.3 in.) - Top cover open Width: 63.5 cm (25 in.) Depth: 66 cm (26 in.) - Front door closed 124.5 cm (49 in.) - Front door open Weight: 204 kg (450 lb) Voltage: 100 V ±10%, 50/60 Hz ±3 Hz Electrical 120 V ±10%, 50/60 Hz ±3 Hz 230 V ±10%, 50/60 Hz ±3 Hz Current Draw: 100 V: 12 Amps max. 120 V: 10 Amps max. 230 V: 5.3 Amps max.
Specifications Laser Specifications Wavelength: 805 - 815 nm Power: 50 mW Type Diode Diode Radiation Class: 3B Imager Radiation Class Class 1 product Temperature: 15° to 35° C (59° to 95° F) Humidity: 15% to 85% RH, non condensing Magnetic Field: < 50 Gauss Altitude 3048 - 12,192 m (100 - 40, 000 feet) Temperature: -35° C to 60° C (-31° F to 140° F) Humidity: 10% to 90% RH, non condensing Altitude Up to 3048 m (10,000 feet) Heat Dissipation: 3000 BTU/hour (average) Acoustical Nois
Specifications Film Sizes The 8150 Laser Imager processes the following film sizes: • 28 x 35 cm DryView Film (11 x 14 in. landscape) • 35 x 35 cm DryView Film (14 x 14 in.) • 35 x 43 cm DryView Film (14 x 17 in.
Blank Page
7 Film Technical Information General Description This section describes the characteristics of Kodak DryView Laser Imaging Film, not the operation of the Kodak DryView 8150 Laser Imager. DryView Laser Imaging Film is a high-resolution, infrared-sensitive, photothermographic film designed specifically for the family of Kodak DryView Laser Imagers. DryView Laser Imaging Film is packaged in daylight load packages, available in blue or clear, 7-mil polyester base.
Film Technical Information Sensitometric Characteristics 3.5 3 DENSITY 2.5 2 1.5 1 0.5 0 0 0.5 1 1.5 2 2.5 3 RELATIVE LOG EXPOSURE H188_1072AC Relative Log Exposure (Example) Image Quality DryView Laser Imaging Film delivers diagnostic-quality, continuous-tone images along with sharp alphanumerics and optimum contrast.
Film Technical Information DryView Laser Imaging Film - US Environmental Regulations Comparison Wet Silver Halide Developer DryView Fixer Wash Film Film Product Regulations OSHA MSDS Required Required Not required Not required Provided DOT Hazardous Hazardous No limits No limits No limits Use permits Local Local None None None Disposal* Regulations EPA Hazardous Hazardous No No No DOT Hazardous Hazardous No No No Note: There is no SUPERFUND liability with DryView Laser I
Film Technical Information Handling Developed Film Handling DryView Laser Imaging Film requires reasonable care. Prolonged exposure to intense light or excessive heat (130° F/54.4° C) for more than 3 hours may cause some gradual darkening of images. Leaving films in vehicles in hot climates for extended periods of time is not recommended. Spills, humidity and other forms of water typically have no significant effect on image quality or film integrity.
Film Technical Information environment. To help maintain optimum performance, the filter requires periodic replacement. DryView Laser Imagers require no special venting. Dissipating Heat September 30, 2004 DryView Laser Imagers use controlled heat to develop DryView Laser Imaging Film. The heat has virtually no effect on the air temperature of the work area. The amount of heat dissipated into an area during a day is typically less than the heat generated by four 100-watt light bulbs.
Blank Page
Glossary AIQC CR CT DICOM Dmax Dmin Dpatch DR DVB DVC GSDF Key operator Modality MR N/A K number Platen Shutdown SMPTE test pattern September 30, 2004 Automatic Image Quality Control. Computed Radiography, the process of creating digital radiographic images. Computed Tomography, the process of creating digital tomographic images. Digital Imaging and Communications in Medicine. A TCP/IP-based protocol for transmitting and receiving medical imaging and related data over a network. Maximum density.
Test type TFT Unprintable queue Glossary-2 The type of test film that will be printed. Two film test types are available: a density test film (SMPTE pattern) and a calibration film. Transfer Function Tables. The queue of jobs that cannot be printed because of errors in the print jobs.
Eastman Kodak Company 343 State Street Rochester, NY 14650 Kodak and DryView are trademarks of Eastman Kodak Company.
