Model: THOR IW—SUB10 In-Wall 10” Subwoofer with 10” SLAPS User Manual Earthquake Sound Corp. | (510) 732-1000 | U.S. Toll Free: (800) 576-7944 | www.earthquakesound.
Table of Contents Introduction...............................................................3 Safety Instructions....................................................3 Unpacking System Components..............................4 System Installation Considerations..........................4 Connection Tips........................................................4 THOR Features........................................................4 What Your THOR Comes With.................................
Introduction Simply put, the THOR is the only in-wall subwoofer that sufficiently provides bass to your home theater system. The THOR remains stable and maintains next to zero resonance because the user can bolt the THOR directly to the studs from the front of the unit. This locks the THOR into the structure of the home. Earthquake engineers also added four dog ear fasteners for added sheet rock support. There are two inches peak-to-peak out of a standard 16” stud gap.
Safety Instructions (continued) Connection Tips 12) Use only a compatible rack or cart for the final resting position. • Keep all power cords away from all signal cables to prevent humming from induced noise. 13) Unplug this apparatus during lightning storm or when unused for a long period of time. 14) Refer all servicing to qualified service personnel.
Installation Preparation • Be sure the THOR is installed by an Earthquake authorized installer • Do not attempt to perform the following steps without a professional (Any product installed by an unauthorized installer is not covered by the Limited 5 Year Warranty) • Tools required for installation: 1) Allen wrench (This tool is provided) 2) Drill or power screw driver 3) Rubber Mallet 4) Razor blade or box cutter 5) Stud finder 6) Pencil 7) Sheet rock saw 8) Measuring device Unpacking Your THOR STEP#1 STE
Taking Off THOR’s Grille Connecting Your THOR STEP#1 Your are now ready to prepare the sub for installation. Carefully remove the logo from the grille to expose the fastener hex nut. Earthquake Sound’s XJ-300FR amplifier is recommended for the use of one THOR. The XJ-300FR amplifier is a 300watt amplifier and can be used as a mono block, a 2 channel amplifier, or bridged for a 2.1 channel amplifier. STEP#2 Using the provided allen wrench, remove the fastener nut.
+ - + - RCA + - HI-LEVEL SPEAKER OUTPUT 110-120V CH1 INPUT 12V DC TRIGGER IR INPUT 220-240V 110-120V~/60Hz 110-120V, FUSE T6.3AL/250V 220-240V~/50Hz 220-240V, FUSE T3.15AL/250V Specifications are subject to change without notice.
Installing Your THOR STEP#1 STEP#3 Note: These pieces are sheet rock stabilizers, not brackets. To begin you will need to locate the empty grille frame. Use your stud finder to locate the studs (if you’re not retrofitting). Using the empty frame, trace your cut line with a pencil. Once you are satisfied with your cut line, begin your cut using the sheet rock saw. In the first image furthest to the left you’ll notice the fastener in it’s neutral position– this is how it is packed.
Assembling the Custom Grille STEP#5 STEP#1 Cut your desired cloth two inches bigger than the frame on all sides. We have provided cloth that can be used, but feel free to use different colors or textures. This procedure is extremely important: Tighten the dogears by fastening the screws which are located at the top of the active driver and the bottom of the passive driver. If you forget to do this the sheet rock will not be secured and the fasteners will be loose and will rattle.
Assembling the Custom Grille (continued) STEP#4 STEP#8 Wrap cloth around frame and put into place with provided security ring. This is what the inside of your grille should look like. Pouring a quick drying glue over the ring and in the space around where the cloth is will add more support and provide a hard shell. STEP#5 STEP#9 Once you have the cloth in place with security ring push the ring enough to keep in place, though the groove with cloth underneath.
Specifications Woofer: 10” (254mm) with 2½” excursion patented design 10” SLAPS Passive Radiator Power Rating: 50-800 Watts RMS Power Rating: 400 Watts Frequency Response: 20Hz-160Hz Sensitivity: 89dB Impedance: 4 Dimensions (HxWxD): 28” x 18 5/8” x 3 3/4” (711mm x 473mm x 95mm) Cut out dimension (HxW): 24” x 13 3/4” (610mm x 349mm) Mounting depth: 3 3/4” (95mm) Finish: white/paintable, custom grille options included Specifications are subject to change without notice.
5 Year Limited Warranty Information Earthquake warrants the original purchaser that all Factory Sealed New Audio Products be free from defects in material workmanship, under normal and proper use, for a period of five (5) years from the date of purchase (as shown on the original sales receipt with the serial number affixed/written on it).