User's Manual

1. Once connect power correctly, the Green led on the
bottom of switch will turn on, switch is ready to serve
2. Push on/off button to turn on/off the light
Reset the product:
Press and hold ON/OFF button for 5 seconds then release, Green
power indicator will flash, switch get into setup mode, please
follow setup instruction to complete setup to start smart
function
On/Off
Button
Status LED
Connection & Operation
1.Scan QR code and download the app iOS or Android
version
2. Register and log in
The user needs to register by mobile phone number.
After registration, you can use this username to log in the
APP and proceed to the next step.
*Support some third-party accounts log in directly .
APP Operation
3. Add Devices
”+“ eht kcilc ,nigol resu eht retfA icon in the upper right corner
of the main page to enter the add device interface, select the
“Switch” menu and click the switch device icon
APP Operation
4. Add Devices
To ensure that the new switch power LED is flashing, select
the Wi-Fi and enter the password then click Next.
APP Operation
5. Add Devices
Wait system to search the device, connect and configure the
device will takes up to 3min.
Once the device configure successfully, please also input
preferred name and select location.
Remark:
1. Smart phone and device must connect to same Wi-Fi during setup mode
2. The device must be added to the account before it can be controlled remotely
3. After the device is successfully accessed, other users can obtain control of the
product through the sharing function.
Troubleshooting
1. Can not connect to Wi-Fi router
a) Also make sure you have good Wi-Fi signal strength at the location of the switch
b) Metal box and metal surface - wall board may block Wi-Fi signal
c) Make sure input correct Wi-Fi password
d) The switch only support 802.11 b/g/n 2.4GHz Wi-Fi signal, 5GHz NOT support
APP Operation APP Operation
6. Control switch with APP
7. Add timer mode in the APP
APP Operation
8. All added devices can be viewed in the main menu of the APP
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for
help.
Features
Product Introduction
- Excellent design and high-quality materials to ensure long-
term stable and reliable service to users
- Wi-Fi connection has the most applicability, and has access
to multiple platforms
- Silent mechanical push button design provide the user's best
feedback
WIFI Connection Mechanical ON/OFF Switch
Input Power:
Control:
Communication:
Control Channel:
Max Current:
Standby Power:
Button Life:
Dimension:
100~240V AC 50~60Hz
Relay
1 CH
WiFi 802.11 b/g/n 2.4GHz
15A
≤0.5W
500K times
105*45*42.5mm
Specification
70
105
45 35
Normal
N L L1 N L L1 Tra
3 Way
Installation
1. Disconnect power by circuit breaker
2. Check the Line with voltage tester pen, make sure the power
is off to prevent electric shock
3. Follow the wiring instructions, connect the dimmer wires to
each other leads and check for short circuits
4. Screw the dimmer into the back box
5. Mounting switch cover plate
6. Connect circuit breaker restore power
Black Wire
– Line In
White Wire
– Neutral Line
Green Wire
– Ground
Blue Wire
– Tra (3 Way)
Red Wire
– Load
Black Wire - Line in
Red Wire - Tra (3 Way)
White Wire - Neutral Line
Green Wire - Ground
Red Wire - Load
N
L
L1
Tra
N
L
L1
Tra
Wiring Instruction of 3 Way Wiring Instruction of Normal
User Manual
Smart Switch V1.0
This equipment complies with FCC radiation exposure limits set
environment. This equipment should be
between the radiator and your body.
forth for an uncontrolled
installed and o
perated with minimum distance
20
cm