ZigBee Soc Module E W N - 8 2 5 8 F A T 1 CC Datasheet V1.0 ZigBee Soc Module E-mail：sales@eardatek.com EDK-Q4-YFB-036 A/0 Earda Technologies Co.
Module：EWN-8258FAT1CC Contents 1 General Specifications ------------------------------------------------- - 3 - 2 Features --------------------------------------------------------------- - 3 2.1 ZigBee Features ----------------------------------------------------------- - 3 - 2.
Module：EWN-8258FAT1CC 1 General Specifications EWN-8258FAT1CC is ZigBee SoC solution with internal Flash and audio support, which combines the features and functions needed for all 2.4GHz IoT standards into a single SoC. 2 Features 2.1 ZigBee Features Based on IEEE 802.15.4 Standard, certified Zigbee Pro and ZigBee 3.0 platform, with ZHA/ZLL profile and ZigBee 3.0 device support. Uses multi-hop mesh networking to eliminate single points of failure and expand the re ach of networks.
Module：EWN-8258FAT1CC 3 System Block Diagram Fig 1 EWN-8258FAT1CC System Block Diagram 4 PHY Specification Table 1 EWN-8258FAT1CC ZigBee RF Parameters Protocol ZigBee Interface UART Frequency 2405 MHz ~ 2480MHz Data rate 802.15.4 250Kbps, ±500Khz deviation Waiting for your suggestion at anytime. -4- E-mail：sales@eardatek.
Module：EWN-8258FAT1CC Table 2 RX Performance Item Sym. min typ Max Unit Condition IEEE802.15.4(250Kbps) RF_Rx performance (±500KHz deviation) Sensitivity 250Kbps Frequency Offset -1/+1 Adjacent channel channel rejection -2/+2 channel magnitude dBm -300 Tolerance Error vector -99.5 +300 42/42 dB Wanted signal at -82dBm 42/42 dB Wanted signal at -82dBm EVM Waiting for your suggestion at anytime. KHz 2% -5- Max(10dBm)power output E-mail：sales@eardatek.
Module：EWN-8258FAT1CC Table 3 TX Performance Item Sym. min typ Max Unit Condition IEEE802.15.4(250Kbps) RF_Tx performance Output power, maximum setting Output power, minimum setting Programmable output power range Modulation 20dB bandwidth Waiting for your suggestion at anytime. 10 dBm -45 dBm 55 dB 2.7 MHz -6- E-mail：sales@eardatek.
Module：EWN-8258FAT1CC 5 Other Specifications Table 4 other Specifications Operating Temperature Storage Temperature -40℃~+105℃ Module: -40℃~+105℃ Package: -20℃~+70℃ Operating Humidity RH 95%(Non-Condensing) Storage Humidity RH 95%(Non-Condensing) Humidity level Level 3 6 DC Specifications Table 5 DC Specifications Item Sym. Min. Typ. Max. Unit Condition VDD_3.3V VBAT 1.8 3.3 3.6 V 3.3V Supply Voltage RX current IRX - 5.3 - mA whole chip TX current ITX - 4.
Module：EWN-8258FAT1CC 7 Module configurations Module Size (Unit: mm): 20.0(±0.2) *15.0(±0.3)*2.4（±0.2） Fig 2 EWN-8258FAT1CC Module Size (TOP VIEW) Waiting for your suggestion at anytime. -8- E-mail：sales@eardatek.
Module：EWN-8258FAT1CC 8 Pin Definition Table 6 the hardware Pin definition of the module Table 6 EWN-8258FAT1CC Pin definition PIN Definition Description 1 VBAT Supply power 1.8V-3.
Module：EWN-8258FAT1CC 9 Module Photos FIG 3 TOP View FIG 4 Bottom View 10 Key material list Table 7 EWN-8258FAT1CC Key material list Type Model Footprint QTY. Crystal 24MHz 12pF 20ppm 3225 1PCS Inductance 10uH 0805 1PCS IC TLSR8258F1KAT32 QFN32 1PCS Waiting for your suggestion at anytime. - 10 - E-mail：sales@eardatek.
Module：EWN-8258FAT1CC 11 Package Information Carrier dimension: （Unit : mm） FIG 5 Carrier size Reel dimension： D=38cm 1500PCS Modules Per Reel FIG 6 Reel Waiting for your suggestion at anytime. FIG 7 Reel figure - 11 - E-mail：sales@eardatek.
Module：EWN-8258FAT1CC 12 Reference design 12.1 RF a) Under the antenna and in the two directions indicated by the arrow, avoid covering the ground, routing and placing metal components. It is better to directly hollow out the PCB in this area. Fig 8 Antenna b) It is recommended not to use any components within 30mm of the module antenna area, and the module baseboard should also avoid wiring and covering the ground as much as possible.
Module：EWN-8258FAT1CC 12.2 Power supply requirement The module power supply voltage is DC+3.3V. The power supply design needs to consider the output current and power interference. The power supply current design needs to reserve 50mA. To avoid the +3.3V power supply from interfering with other circuits on the motherboard, it is recommended to supply to the module using the regulator circuit alone. the recommended DC-DC circuit structure shown in the figure below. A 4.
Module：EWN-8258FAT1CC 12.3 Motherboard interference avoidance Motherboard interference comes from: high-speed data interface (HDMI), the Operating frequency of main chip, DDR, DC-DC power supply. The method of avoiding interference according to the characteristics of various signals is also different. The main methods of interference avoidance include: 1. keeping away from the source of interference; 2. Adding shields to avoid interference leakage; 3. Reasonable layout to eliminate interference. 12.3.
Module：EWN-8258FAT1CC Fig 11 HDIM and USB interference 12.3.2 The main chip interferes with DDR Because the main chips operate at about 800MHz or DDR2 operate at 667MHz, 3x frequency of 800MHz and 4x frequency of 667MHz are near 2.4GHz band. It must to place BT modules and antennas far away from the main chip and DDR. It is strongly recommended that the main chip be isolated from the DDR by a shield. As shown in the figure below.
Module：EWN-8258FAT1CC 12.4 Recommended secondary reflux temperature curve T he number of reflux shall not exceed 2 times, and the tin feeding height of the half hole of the module shall be no less than 1/4. The lead-free reflux curve requirements of BT module products are shown in figure 13： Fig 13 Furnace temperature curve Note: 1. The maximum furnace temperature of the module is 260℃, don't exceed this temperature. 2. The gold plating thickness of the module pad is 2u".
Module：EWN-8258FAT1CC 13 Revision History Revision Release Date V1.0 2022-9-7 Summary Revised By First release Yuan FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Module：EWN-8258FAT1CC IC Caution Radio Standards Specification RSS-Gen, issue 5 - English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device.
Module：EWN-8258FAT1CC OEM integration instructions: This device is intended only for OEM integrators under the following conditions: The transmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with the external antenna(s) that has been originally tested and certified with this module. As long as the conditions above are met, further transmitter test will not be required.
Module：EWN-8258FAT1CC Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC/IC rules FCC Part 15 Subpart C 15.247 & 15.207 & 15.209& RSS GEN&RSS 247 2.3 Specific operational use conditions The module is a ZigBee module with 2.4G function. Operation Frequency: 2405-2480MHz Number of Channel: 16 Modulation: OQPSK Type: PCB Antenna Gain: -1.99 dBi Max. The module can be used for mobile or applications with a maximum 0.5dBi antenna.
Module：EWN-8258FAT1CC 2.7 Antennas PCB Antenna Type: OQPSK Gain: -1.99dBi This device is intended only for host manufacturers under the following conditions: The transmitter module may not be co-located with any other transmitter or antenna; The module shall be only used with the internal antenna(s) that has been originally tested and certified with this module. The antenna must be either permanently attached or employ a ‘unique’ antenna coupler.
Module：EWN-8258FAT1CC 2.9 Information on test modes and additional testing requirements Operation Frequency: 2405~2480MHz Number of Channel: 16 Modulation: OQPSK Host manufacturer must perfom test of radiated & conducted emission and spurious emission, etc. according to the actual test modes for a stand-alone modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product.
