User's Manual

ManualsBrandsEarda Technologies ManualsElectrical EquipmentSmart Dimmer Switch

USER MANUAL

SMART DIMMER SWITCH

200MM

520MM

正面

反面

正面

04 Contents Supplied

03 Specification

Dimmer Panel Wire Connectors Screws

LED

—up to 250W

Incandescent/halogen

—up to 300W

Input Power:

Dimming Control:

Communication:

Load：

Standby Power:

Button Life:

100~120V AC 60Hz

Leading Edge

BLE MESH 2.4GHz**

< 300W Incandescent/Halogen

≤1.8W

< 250W LED

500K times

105*45*45 mmDimension:

Single Pole / 3 Way

** BLE MESH model must use with BLE MESH Gateway to access internet

Recommended loads:

V3.0 A

STEP 5

Identify The Old dimmer

3-Way 3-Way

Single Pole Dimmer

3-Way Dimmer

Single Pole

Find the NEUTRAL Wires

Neutral wire is required to install the smart dimmer .Most likely a bundle

of one or more white wires in the wall.

Test NEUTRAL and GROUND Wires

Make sure there is no power on the neutral wires from neighboringcir-

cuit. lf necessary, shut off additional circuits until no voltage is found.

GROUND wires are usually BARE COPPER or GREEN.

STEP 7

STEP 8

Neutral

Ground

Traveler

Line /Hot

Note: If there is no neutral, please try another

location or call an electrician for help.

STEP 6

ldentify Line/Load Wire

Note:The color of your wire may be different from

the color shown on the manual.

Two Dimmer control the same light or the same bundle of lights.

Only one dimmer control one light or a bundle of lights.

3-Way Dimmer

LINE/LOAD wire (usually BLACK, attached with a black screw, and may

be Remarked "common".)

Line /Hot

Traveler

Line /Hot

Load

Traveler

Neutral

STEP 9

Take Pictures of the Wiring

Loosen the screw terminals and remove the old dimmer.

02 Indicator Light Status

Switch Status RemarksLight StatusLight Color

Green

White

OFF

Power ON

Support Self-

deﬁnition on APP

The white light is

enabled only when

the switch status

is on.

Power OFFDefault)

Blink Quickly

(0.5s intercal)

Blink Slowly

(1s interval)

Ready for AP

(Access Point)

conﬁguration mode

Ready for default

conﬁguration mode

01 Product Outline

On/Off

Switch

Touch

Dimming

Panel

Dimming Levels

Status LED

OFF

Not Connected to

the cloud

Connected to router

and connected to

cloud

Tools you’ll need

Flat-head Screwdriver

Phillips-head Screwdriver Pliers

06 Installation

05 Safety Information

Electricity can cause personal injury and property damage if handled

improperly.If you are not sure about any part of these instructions,

please seek professional assistance from a qualiﬁed electrician.

Ensure all wark meets applicable local and national codes.

WARNING: RISK OF ELECTRIC SHOCK

Voltage Tester

1 3 5

This device complies with Industry Canada licence-exempt

RSS standard(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference

that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada

applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible

d'en compromettre le fonctionnement.

This equipment complies with IC radiation exposure limits

set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance

20cm between the radiator & your body.

IC Caution

FCC Caution

This device complies with part 15 of the FCC Rules. Operation

is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

§ 15.21 Information to user.

Any Changes or modiﬁcations not expressly approved by the

party responsible for compliance could void the user's

authority to operate the equipment.

§ 15.105 Information to the user.

Note: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following

measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for

help.

This equipment complies with FCC radiation exposure limits

set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance

20cm between the radiator & your body.

After you assign rooms for the Switch,your Switch

will be listed in the Home Control page

If you set the name as “bedroom light”, the supported voice

commands are as below:

Ok Google, turn on bedroom light.

Ok Google, set bedroom light to 50%.

Control your smart switch through Google Home

Now you can control your smart switch through

Google Home.

STEP 4

STEP 5

Find "Smart Life" in the list

STEP 2

STEP 3

Input your Smart Life account and password you

registered in Part 2, then tap "Link Now".

10 Smart Life Skills (Google)

Find "Home Control" in the hamburger menu on the

Google Home app’s home page > Home Control

> tap "+".

STEP 1

The Account is linked successfully, and then tap

Authorize to Complete.

To add or delete switches, please delete or add them in the Smart Life

App (See Part 2) and then the Alexa will synchronize automatically.

If you cannot see the name of switches in the Devices List in Alexa Page,

You can click “Discover” in Alexa page it will synchronize from the Smart

Life App.

Congratulations! Alexa Devices (Echo) can Control

the Swtich ON/OFF.

STEP 5

STEP 6

The account and password should

be the same that you registered in

the smart life app

Enable the skill

Part 2, then click “Link Now”

STEP 4

STEP 3

09 Smart Life Skills (Alexa)

computer,then tap Home>Skills & Games

STEP 1

STEP 2

Search "Smart Life”and select the right one

according the blue logo (same with App)

08 Reset

Press and hold Switch button for 5s to reset the

Dimmer and get into quick conﬁgure mode

LED Flashing

Locate your circuit breaker panel and turn off the power to each

switch you are replacing.

Remove the switch and pull it away from the wall.

STEP 2

STEP 3

STEP 4

STEP 1

Circuit breaker panel

Turn Off Power

Verify Power is Off

Pull Out Old dimmer

You may need to turn off more than on circuit breaker.

We recommend you to remove the faceplate from the old switch and

use an electrical tester to test all wires connected to the switch to

ensure there is no voltage in the circuit.

Approximately

30 minutes to install

and setup the dimmer

30min

Available for selected model

Connection Diagram

—Single Pole

Connection diagram

—3 Way Wiring Diagram

(Smart Dimmer & Traditional Switch)

*For 3Way model Only

Smart

Dimmer

Traditional

Switch

Not Working Situation

Smart SwitchSmart Dimmer

Smart Dimmer Smart Dimmer

Smart Dimmer Traditional dimmer

switch

STEP 10

Wire the Smart Dimmer Switch

Mount The Dimmer

Use the screws provided.

Attach the adapter to the dimmer using the

screws provided and snap on the wallplate.

Attach The Wallplate

STEP 12

STEP 11

Turn on the power

The light(s) may ﬂash once during smart dimmer

ﬁrst time power up

Cap off the remaining L1 wire (RED) from the Switch with a

wire nut.

Connection diagram

—3 Way Wiring Diagram

(Smart Dimmer & Non-Smart Switch)

*For 3Way model Only

Smart

Dimmer

Traditional

Switch

Replace ONE of your REGULAR

3-WAY SWITCHES with SMART

SWITCH

Add the Switch To APP

Preparation:Ensure the switch has connected with electricity; ensure your

phone has connected to Wiﬁ router and is able to connect to the internet.

After the user login,Tap the “+” icon on the top right conner to add

device;slect the “dimmer”menu and choose the switch device icon.

Note: BLE MESH versions have slightly different to access the

APP. Please make sure that the corresponding gateway is

online, and then select the applicable gateway to add the

switch(es).

STEP 3

My Home

Please scan QR code and download the Smart Life app

iOS or Android version

Download Smart Life APP

Enter the Register/Login interface; tap “Register” to create an account by

entering your phone umber to get veriﬁcation code and “Set password”,

Choose“Log in” if you already have a Smart Life account some third-party

accounts log in directly.

07 Add Devices

STEP 1

STEP 2

）etihW（lartueN

N L

Ground

（Green）

Load(red)

Line/Hot(black)

Neutral

L1 Common

）etihW（lartueN

alb（toH/ eniL

Ground

（Green）

Traveler

Neutral

L1L2 Common

Neutral

L2 Common

)kcalb（toH/ eniL

Ground

（Green）

Common

N L

）etihW（lartueN

Traveler