User's Manual

ManualsBrandsEarda Technologies ManualsElectronicsSmart Switch

USER MANUAL

SMART SWITCH

200MM

520MM

正面

反面

正面

200X520MM 四色印刷

80g哑光纸风琴折

ON/OFF

LED Indicator

Cover Panel

02 Indicator Light Status

Switch Status RemarksLight StatusLight Color

Green

OFF

Power OFF(Default)

Support Self-

deﬁnition on APP

Power ON(Default)

Blink Quickly

(0.5s )

Blink Slowly

(1s )

Ready for AP

(Access Point)

conﬁguration mode

Ready for default

conﬁguration mode

01 Product Outline

Control switch with APP

All added devices can be viewed in the

main menu of the APP

STEP 4

STEP 5

10 Smart Life Skills (Google)

Find "Home Control" in the hamburger menu on the

Google Home app’s home page > Home Control

> tap "+".

STEP 1

Find "Smart Life" in the list

STEP 2

STEP 3

Input your Smart Life account and password you

registered in Part 2, then tap "Link Now".

After you assign rooms for the Switch,your Switch

will be listed in the Home Control page

If you set the name as “bedroom light”, the supported voice

commands are as below:

Ok Google, turn on bedroom light.

Ok Google, set bedroom light to 50%.

Control your smart switch through Google Home

Now you can control your smart switch through

Google Home.

STEP 4

STEP 5

FCC Caution

This device complies with part 15 of the FCC Rules. Operation

is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

§ 15.21 Information to user.

Any Changes or modications not expressly approved by the

party responsible for compliance could void the user's

authority to operate the equipment.

§ 15.105 Information to the user.

Note: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following

measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for

help.

This equipment complies with FCC radiation exposure limits

set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance

20cm between the radiator & your body.

08 Reset

Press and hold Switch button for 8s until indicator

ashing to reset the Switch and get into quick

congure mode

LED Flashing

The Account is linked successfully, and then tap

Authorize to Complete.

To add or delete switches, please delete or add them in the Smart Life

App (See Part 2) and then the Alexa will synchronize automatically.

If you cannot see the name of switches in the Devices List in Alexa Page,

You can click “Discover” in Alexa page it will synchronize from the Smart

Life App.

Congratulations! Alexa Devices (Echo) can Control

the Swtich ON/OFF.

STEP 5

STEP 6

09 Smart Life Skills (Alexa)

computer,then tap Home>Skills & Games

STEP 1

STEP 2

Search "Smart Life”and select the right one

according the blue logo (same with App)

The account and password should

be the same that you registered in

the smart life app

Enable the skill

Part 2, then click “Link Now”

STEP 4

STEP 3

This device complies with Industry Canada licence-exempt

RSS standard(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference

that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada

applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible

d'en compromettre le fonctionnement.

This equipment complies with IC radiation exposure limits

set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance

20cm between the radiator & your body.

IC Caution

04 Contents Supplied

03 Specification

Switch Panel

Recommended loads:

*Zigbee model must use with Zigbee 3.0 Gateway to access internet

** BLE MESH model must use with BLE MESH 2.4GHz** Gateway to access internet

Screws

LED Motor

—up to 350W —up to 0.6 HP

Incandescent/halogen

—up to 1000W

Input Power:

Control:

Communication:

Available for selected model

Max Current:

Standby Power:

Button Life:

100~120V AC 60Hz

Relay

WiFi 802.11 b/g/n 2.4GHz

Zigbee 3.0*

BLE MESH 2.4GHz**

10A

≤0.5W

500K times

105*45*42.5 mmDimension:

Tools you’ll need

Flat-head screwdriver

Phillips-head screwdriver Pliers

06 Installation

05 Safety Information

Electricity can cause personal injury and property damage if handled

improperly.If you are not sure about any part of these instructions,

please seek professional assistance from a qualied electrician.

Ensure all wark meets applicable local and national codes.

WARNING: RISK OF ELECTRIC SHOCK

Voltage tester

Approximately

30 minutes to install

and setup the switch

30min

USER MANUAL

SMART SWITCH

Single Pole / 3 Way

V2.0 A

1 3 5

6 82

2523

2422

Common

Neutral（White）

Line /Hot（black)

Traveler

Traditional

Switch

Smart

Switch

Traditional

Switch

Smart

Switch

Ground

（Green）

Neutral

Common

Line /Hot（black)

Ground

（Green）

Neutral

Common

Traveler

Single Pole Wiring Diagram

( 3-Way Model）

Single Pole Wiring Diagram

Neutral

Common

Neutral（White）

Line /Hot（black)

STEP 10

Ground

（Green）

3-way Smart Switch

9 11 13

1210 14

Wait system to search the device,connect and conﬁgure the

device will takes up to 3min.

Once the device conﬁgure successfully, please also input preferred

name and select location.

Quick Conguration Mode

Remark:

Smart phone and device must connect to same Wi-Fi during setup mode

The device must be added to the account before it can be controlled remotely

After the device is successfully accessed, other users can obtain control

of the product through the sharing function.

Make sure you have good Wi-Fi singal strength at the location of the switch

Metal box and MATEL Surface-wall board may block Wi-Fi signal

Make sure input correct Wi-Fi password

Troubleshooting

STEP 3.1

3-Way Wiring Diagram

Neutral

Common

Neutral

Common

Neutral（White）

Ground

（Green）

Line /Hot（black)

Smart

Switch

Smart

Switch

Ground

（Green）

Traveler

3-Way Wiring Diagram

Locate your circuit breaker panel and turn off the power to each

switch you are replacing.

Remove the switch and pull it away from the wall.

STEP 2

STEP 3

STEP 4

STEP 5

STEP 1

Circuit breaker panel

Turn Off Power

Verify Power is Off

Pull Out Old Switch

Identify The Old Switch

3-Way 3-Way

Single Pole Switch

3-Way Switch

Single Pole

You may need to turn off more than on circuit breaker.

We recommend you to remove the faceplate from the old switch and

use an electrical tester to test all wires connected to the switch to

ensure there is no voltage in the circuit.

Find the NEUTRAL Wires

Neutral wire is required to install the smart light switch.Most likely a

bundle of one or more white wires in the wall.

Test NEUTRAL and GROUND Wires

Make sure there is no power on the neutral wires from neighboringcir-

cuit. lf necessary, shut off additional circuits until no voltage is found.

GROUND wires are usually BARE COPPER or GREEN.

STEP 7

STEP 8

Neutral

Ground

Traveler

Line /Hot

Note: If there is no neutral, please try another

location or call an electrician for help.

STEP 6

ldentify Line/Load Wire

Note:The color of your wire may be different from

the color shown on the manual.

Two switches control the same light or the same bundle of lights.

Only one switch control one light or a bundle of lights.

Wire the Smart Switch

STEP 12

Turn on the power

Add the Switch to APP

The light(s) may ash once during smart switch

rst time power up

Preparation:Ensure the switch has connected with electricity; ensure your

phone has connected to Wi router and is able to connect to the internet.

After the user login,Tap the “+” icon on the top right conner to add

device;slect the “switch”menu and choose the switch device icon.

Note: Zigbee and BLE MESH versions have slightly different to

access the APP. Please make sure that the corresponding

gateway is online, and then select the applicable gateway to

add the switch(es).

STEP 3

Mount the switch

STEP 11

Not Working Situation

Traditonal Dimmer

Smart Dimmer

Smart

Switch

Note: For more detailed content, please watch

the wiring video on product page.

Cap off the remaining L2 wire (RED) from the Switch

with a wire nut.

Neutral

Line

Neutral（White）

Line /Hot（black)

Ground

（Green）

Smart Switch

Replace ONE of your REGULAR

3-WAY SWITCHES with SMART

SWITCH

Replace BOTH of your REGULAR

3-WAY SWITCHES with SMART

SWITCHES

Please scan QR code and download the Smart Life app

iOS or Android version

Download Smart Life APP

Enter the Register/Login interface; tap “Register” to create an account by

entering your phone umber to get verication code and “Set password”,

Choose“Log in” if you already have a Smart Life account some third-party

accounts log in directly.

07 Add Devices

STEP 1

STEP 2

3-Way Switch

LINE/LOAD wire (usually BLACK, attached with a black screw, and may

be Remarked "common".)

Line /Hot

Traveler

Line /Hot

Load

Traveler

Neutral

STEP 9

Take Pictures of the Wiring

Loosen the screw terminals and remove the old switch.

Wire Caps

Press and hold Switch button for 8s to reset the Switch and get into

quick congure mode

Select the Wi-Fi and enter the password then click Next Wait for

completing the connection.