E-TOP GS293d 300+300Mbps Gigabit Server Router User Manual http://www.sapido.com.tw/ 1 User Manual v1.0.
Table of Contents Table of Contents .................................................................................................................................. 2 FCC Caution ..........................................................................................................................................2 Chapter 1 Introduction ................................................................................................................. 6 1.1 Hardware Features............................
4.1.2.2 Enable Universal Repeater Mode ....................................................................... 43 4.2 Wireless Security Setup ...........................................................................................44 4.3 Wireless Access Control ..........................................................................................46 Chapter 5 Router Mode Security Setup....................................................................................48 5.1 NAT ...............
6.4.1 Network Config.................................................................................................79 6.4.2 Event Log ..........................................................................................................80 6.5 Chapter 7 Logout ........................................................................................................................82 Samba Server .........................................................................................................
FCC Statement in User’s Manual (for calss B) FCC Section 15.105 “Federal Communications Commission (FCC) Statement” This equipment has been tested and found to comply with the limits for a lass B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Chapter 1 1.1 Introduction Hardware Features http://www.sapido.com.tw/ 6 User Manual v1.0.
1.2 Product Appearance LED Indicator Status Description: http://www.sapido.com.tw/ 7 User Manual v1.0.
http://www.sapido.com.tw/ 8 User Manual v1.0.
Chapter 2 System and Network Setup The GS293d is an easy to setup and wireless device for various application and environment, especially for large installs such as hotels, offices space, warehouses, hot-spots and more. To begin with GS293d, you must have the following minimum system requirements. If your system can’t correspond to the following requirements, you might get some unknown troubles on your system. λ Internet Account for XDSL/Cable Modem, or 3G.
2.1.2 AP Mode Switch to AP mode, if a router is already set at the house, and you want to make the wireless LAN communication. 2.1.3 Wi-Fi AP Mode Switch to WiFi AP Mode when you connect to the internet wirelessly through PC and wireless device without wireless LAN function equipped. 2.2 Connecting GS293d Prepare the followings before the connection: λ PC or Notebook for setup λ Ethernet cable or 3G modem http://www.sapido.com.tw/ 10 User Manual v1.0.
1. Make sure you are under “Router Mode”. 2. Connect GS293d to xDSL/ Cable modem with the Ethernet cable, WAN to LAN. 3. Turn on your Computer. 2.3 Network setup After the network connection is built, the next step is setup the router with proper network parameters, so it can work properly in your network environment.
Windows Vista/Win7 2.3.1 - please go to section 2.3.3 Windows 2000 Click “Start” button (it should be located at lower-left corner of your computer), then click control panel. Double-click Network and Dial-up Connections icon, double click Local Area Connection, and Local Area Connection Properties window will appear. Select “Internet Protocol (TCP/IP)”, then click “Properties”. 1. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”. http://www.
2.3.2 1. Windows XP Click “Start” button (it should be located at lower-left corner of your computer), then click control panel. Double-click Network and Internet Connections icon, click Network Connections, then double-click Local Area Connection, Local Area Connection Status window will appear, and then click “Properties”. 2. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”, then click “OK”. http://www.sapido.com.tw/ 13 User Manual v1.0.
2.3.3 1. Windows Vista / Windows 7 Click “Start” button (it should be located at lower-left corner of your computer), then click control panel. Click View Network Status and Tasks, and then click Manage Network Connections. Right-click Local Area Network, then select “Properties”. Local Area Connection Properties window will appear, select “Internet Protocol Version 4 (TCP / IPv4)”, and then click “Properties”. 2.
2.4 Router IP Address Lookup After the IP address setup was completed, please clicks “start” → “run” at the bottom-lower corner of your desktop: Input “cmd”, and then click “OK”. http://www.sapido.com.tw/ 15 User Manual v1.0.
Input “ipconfig”, then press “Enter” key. Please check the IP address followed by “Default Gateway” (In this example, the gateway IP address of router is 192.168.1.1) NOTE: If the IP address of Gateway is not displayed, or the address followed by ‘IP Address’ begins with “169.x.x.x”, please recheck network connection between your computer and router, and / or go to the beginning of this chapter, to recheck every step of network setup procedure. 2.4.
http://www.sapido.com.tw/ 17 User Manual v1.0.
http://www.sapido.com.tw/ 18 User Manual v1.0.
Chapter 3 Internet Connection This Chapter describes how to setup GS293d to the internet. The GS293d is delivered with the following factory default parameters. Default IP address: 192.168.1.1 (Router Mode) 192.168.1.254 (AP Mode) 192.168.1.254 (WiFi AP Mode) Default IP subnet mask: 255.255.255.0 Web login user name: admin Web login password: admin 3.1 Plug and Play The GS293d supports four types of Internet connection method: 3G modem card, wire or wireless connection via xDSL/Cable modem.
Step 2. Select “USB Tethering” as connection type. Step 3. Click on “Done”. Step 4. Wait few seconds for pairing. When WAN LED on, the Internet is ready to access. Note: 1. iPhone: (1) Due to difference in 3G service bundled in various carriers, please check your 3G service supports Internet tethering. (2) Enable Internet Tethering on iPhone 3GS / iPhone 4, and set up the screen lock to never to prevent the sharing is interrupted unexpected by the iPhone screen lock feature. 2.
1. Open a Web browser, and enter http://192.168.1.1 (Default Gateway) into the blank. 2. Enter the User name and Password into the blank and then click Login. The default values for User Name and Password are admin (all in lowercase letters). 3.2.1 WAN Interface- Ethernet Port The WAN access type is depended on the service that you contract with the provider. The GS293d provides five selections for the WAN access type, Static IP, DHCP Client, PPPoE, PPTP and L2TP. 3.2.1.
Select WAN under the IP Config menu, and choose Ethernet Port for the WAN Interface. Its associated setting will show up. Item Description WAN Access Type Select “Static IP” IP Address Enter the IP address which is provided by your ISP. Subnet Mask Please enter the Subnet Mask address Default Gateway Input ISP Default Gateway Address, . http://www.sapido.com.tw/ 22 User Manual v1.0.
DNS Input DNS information which is provided by your ISP Backup select Select 3G as a back up solution or none. Clone Mac Address Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MAC Address" Apply Change & Reset Click on Apply Change to save the setting date, or you may click on Reset to clear all the input data. 3.2.1.2 DHCP Client Item http://www.sapido.com.tw/ Description 23 User Manual v1.0.
WAN Access Type Select "DHCP Client" Host Name You can keep the default as the host name, or input a specific name if required by your ISP. DNS Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your ISP in DNS 1 2 3. Backup select Select 3G as a back up solution or none. Clone Mac Address Some ISPs require MAC address registration.
Item Description WAN Access Type Select "PPPoE" User Name Input your user name provided by your ISP. If you don’t know, please check with your ISP. Password Input the password provided by your ISP. Service Name Input the service name provided by your ISP. Connection Type Three types for select: Continues, Connect on Demand, and Manual. DNS Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your ISP in DNS 1 2 3.
3.2.1.4 PPTP Item Description WAN Access Type Select "PPTP" Server IP Address Input your server IP address provided by your ISP. If you don’t know, please check with your ISP. http://www.sapido.com.tw/ 26 User Manual v1.0.
User Name Input PPTP account provided by your ISP. Password Input the password provided by your ISP. DNS Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your ISP in DNS 1 2 3. Backup select Select 3G as a back up solution or none. Clone Mac Address Some ISPs require MAC address registration.
Item Description WAN Access Type Select "PPTP" Server IP Address / Host Name Input your server IP address or Host Name provided by your ISP. If you don’t know, please check with your ISP. User Name Input PPTP account provided by your ISP. Password Input the password provided by your ISP. DNS Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your ISP in DNS 1 2 3. http://www.sapido.com.tw/ 28 User Manual v1.0.
Backup select Select 3G as a back up solution or none. Clone Mac Address Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MAC Address" Apply Change & Reset Click on Apply Change to save the setting date, or you may click on Reset to clear all the input data. 3.2.1.6 Advance function Item Description MTU Maximum Transmission Unit. Usually provide by computer operation systems (OS). Advanced users can set it manually.
Item Description APN (Access Point Name) Enter the access point name. If you do not know the setting information for APN, check with your 3G service provider. User Name Enter the User Name supplied by the provider. Password Enter the password supplied by the provider. Phone Number Enter the subscribing access point's phone number. DNS Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your ISP in DNS 1 2 3.
internet. Enable IGMP Proxy Enable IGMP Proxy to provide the service for IP hosts and adjacent multicast routers to establish multicast group memberships. Enable Ping Access on WAN Enable Ping Access on WAN will make WAN IP address response to any ping request from Internet users. However, it is also a comma way for hacker to ping public WAN IP address, to see is there any WAN IP address available. Enable Web Server Access on WAN This option is to enable Web Server Access function on WAN.
Item Description Refresh You can see a list of available Wireless networks. Select the preferred one. Encryption type Select the Encryption type form the drop-down list. WAN Access Type Select Static IP, DHCP, PPPoE, PPTP or L2TP. DNS Select Attain DNS Automatically. Or select Set DNS Manually, if you want to specify the DNS, and enter the DNS provided by your ISP in DNS 1 2 3. Clone Mac Address Some ISPs require MAC address registration.
Make sure to shift the mode into AP Mode. When this product is used as an access point, the IP address has to be changed. The default IP under AP mode is 192.168.1.254. 1. Open a Web browser, and enter http://192.168.1.254 (Default Gateway) into the blank. 2. Enter the User name and Password in to the blank and then Click Login. The default values for User Name and Password are admin (all in lowercase letters). Select LAN under the IP Config menu http://www.sapido.com.tw/ 33 User Manual v1.0.
Item Description Device Name Input a name for this router. IP Address The default IP address is 192.168.1.254 Subnet Mask Enter the Subnet Mask address Default Gateway Enter the Default Gateway address for LAN interfaces DHCP Select DHCP type: Client, Disable, or Server under different environment. DHCP Client Range When enable DHCP server, you can fill in the start and end IP address; client will be assigned an IP address from the range. 802.1d Spanning Tree Disable or Enable the 802.
The default gateway is http://192.168.1.254 and for User Name and Password are admin (all in lowercase letters). Click Login to enter. http://www.sapido.com.tw/ 35 User Manual v1.0.
Item Description Device Name Input a name for this router. IP Address The default IP address is 192.168.1.254 Subnet Mask Enter the Subnet Mask address Default Gateway Enter the Default Gateway address for LAN interfaces DHCP Select DHCP type: Client, Disable, or Server under different environment. DHCP Client Range When enable DHCP server, you can fill in the start and end IP address; client will be assigned an IP address from the range. 802.1d Spanning Tree Disable or Enable the 802.
Chapter 4 4.1 Wireless Setup Wireless Setup There are two ways to setup wireless LAN with GS293d. You can use either way to setup Wireless LAN. 4.1.1 Setup Wireless LAN by WPS button You can setup wireless LAN easily by using the WPS button if both WLAN router and the WLAN adapter (client) are WPS supported. Before starting the setup, please check the things below: λ Get ready for Internet connection with GS293d λ The WLAN adapter is finished installation and plug in your computer/ laptop.
(7) Back to the WLAN adapter utility and click its “PBC” (C) button. The utility will start searching the destination connection. (8) Confirm the information form the Utility http://www.sapido.com.tw/ 38 User Manual v1.0.
(9) After completes the WPS setup. Please confirm that it can be connected to the Internet. Note: The setup image might be some differences when using other branded Adapter. 4.1.2 Wireless Basic Setup from Web GUI The Wireless Basic Settings include Band, Mode, SSID, Channel Number and other wireless settings. http://www.sapido.com.tw/ 39 User Manual v1.0.
http://www.sapido.com.tw/ 40 User Manual v1.0.
Item Description Disable Wireless LAN Interface Turn off the wireless service. 2.4G Band Select the frequency. It has 6 options: 2.4 GHz (B/G/N/B+G/G+N/B+G+N). 5G Band Select the frequency. It has 3 options: 5 GHz (A / N / A+N). Mode Select the mode. It has 3 modes to select: (AP, Client,). Multiple AP * In Wi-Fi AP mode only support Client mode. SSID Service Set identifier, users can define to any or keep as default.
Enable MAC Clone (Single Ethernet Client) Clone the MAC address for ISP to identify. Enable Universal Repeater Mode (Acting as AP and Client simultaneously) Allow to equip with the wireless way conjunction upper level, provide the bottom layer user link in wireless and wired way in the meantime. (The IP that bottom layer obtains is from upper level.) Please also check Section 4.1.2.
Active Client List Display the properties of the client which is connecting successfully. Apply Change & Reset Click on Apply Change to save the setting date, or you may click on Reset to clear all the input data. 4.1.2.2 Enable Universal Repeater Mode The router can act as Station and AP at the same time. It can use Station function to connect to a Root AP and use AP function to service all wireless stations within its coverage.
4.2 Wireless Security Setup Here users define the security type and level of the wireless network. Selecting different methods provides different levels of security. Please note that using any encryption may cause a significant degradation of data throughput on the wireless link. There are five Encryption types supported: “None”, “WEP”, “WPA (TKIP)”, ”WPA2(AES)”, and “WPA2 Mixed”. Enabling WEP can protect your data from eavesdroppers.
different shared key formats (ASCII and Hex) for wireless network. (2) 802.1x Authentication It is a safety system by using authentication to protect your wireless network. 2. Encryption- WPA (WPA, WPA2, and WPA2 Mixed), WPA Authentication Mode (1) Enterprise (RADIUS): Please fill in the RADIUS server Port, IP Address, and Password (2) Personal (Pre-Shared Key): Pre-Shared Key type is ASCII Code; the length is between 8 to 63 characters. If the key type is Hex, the key length is 64 characters.
(3) Apply Change & Reset: Click on ‘Apply Changes’ to save setting data. Or click ‘Reset’ to reset all the input data. 4.3 Wireless Access Control Access Control allows user to block or allow wireless clients to access this router. Users can select the access control mode, then add a new MAC address with a simple comment and click on “Apply Change” to save the new addition. To delete a MAC address, select its corresponding checkbox under the Select column and click on “Delete Selected” button.
(2) The MAC address what you set will be displayed on the Current Access Control List. (3) The wireless client will be denied by the wireless router. http://www.sapido.com.tw/ 47 User Manual v1.0.
Chapter 5 Router Mode Security Setup This section contains configurations for the GS293d’s advanced functions such as: virtual server, DMZ, and Firewall to provide your network under a security environment. 5.1 NAT 5.1.1 Virtual Server The Virtual Server feature allows users to create Virtual Servers by re-directing a particular range of service port numbers (from the WAN port) to a particular LAN IP address. Item Description Enable Port Forwarding Select to enable Port Forwarding service or not.
5.1.2 Virtual DMZ The DMZ feature allows one local user to be exposed to the Internet for special-purpose applications like Internet gaming or videoconferencing. When enabled, this feature opens all ports to a single station and hence renders that system exposed to intrusion from outside. The port forwarding feature is more secure because it only opens the ports required by that application. Item Description Enable DMZ It will enable the DMZ service if you select it.
5.2.1 Port Filtering When enabled packets are denied access to Internet/filtered based on their port address. Item Description Enable Port Filtering Select Enable Port Filtering to filter ports. Port Range Enter the port number that needs to be filtered. Protocol Please select the protocol type of the port. http://www.sapido.com.tw/ 50 User Manual v1.0.
